MULTIQUIP Mikasa Series Guide

SAFETY AND OPERATIONS INSTRUCTIONS FROM:
PLEASE READ THIS INFORMATION CARFULLY PRIOR TO
OPERATING EQUIPMENT

PAGE 2 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
PROPOSITION 65 WARNING

PAGE 6 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
SAFETY INFORMATION

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 7
GENERAL SAFETY
CAUTION
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
NEVER operate this equipment under the influence of
drugs or alcohol.
ALWAYS check the equipment for loosened threads or
bolts before starting.
DO NOT use the equipment for any purpose other than
its intended purposes or applications.
NOTICE
This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
ALWAYS know the location of the nearest
fire extinguisher.
ALWAYS know the location of the nearest
first aid kit.
ALWAYS know the location of the nearest phone or keep a
phone on the job site. Also, know the phone numbers of
the nearest ambulance, doctor and fire department. This
information will be invaluable in the case of an emergency.
RAMMER SAFETY
DANGER
NEVER operate the equipment in an explosive
atmosphere or near combustible materials.An
explosion or fire could result causing severe
bodily harm or even death.
WARNING
NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety
.
Disconnection of these devices can cause severe injury,
bodily harm or even death. Disconnection of any of these
devices will void all warranties.
DO NOT use this machine on ground that is harder than
the machine can handle, or for driving pilings or tamping
rock beds. Furthermore, use of the machine on sloping
ground, such as the side of an embankment, may make
the machine unstable and can cause an accident. It can
also result in premature machine wear due to uneven
loads on the machine.
Use the machine with confidence for tamping earth and
sand, soil, gravel, and asphalt. DO NOT use the machine
for other types of jobs.
CAUTION
NEVER lubricate components or attempt service on a
running machine.
NOTICE
ALWAYS keep the machine in proper running condition.
Fix damage to machine and replace any broken parts
immediately.
ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
SAFETY INFORMATION

PAGE 8 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
ENGINE SAFETY
DANGER
The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
cause death if inhaled.
The engine of this equipment
requires an adequate free flow
of cooling air. NEVER operate
this equipment in any enclosed
or narrow area where free flow
of the air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
WARNING
DO NOT place hands or fingers inside engine
compartment when engine is running.
NEVER operate the engine with heat shields or
guards removed.
DO NOT remove the engine oil drain plug
while the engine is hot. Hot oil will gush
out of the oil tank and severely scald any
persons in the general area of the rammer.
CAUTION
NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to cool
before servicing equipment.
NOTICE
NEVER run engine without an air filter or with a dirty air
filter. Severe engine damage may occur. Service air filter
frequently to prevent engine malfunction.
NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
FUEL SAFETY
DANGER
DO NOT add fuel to equipment if it is placed inside truc
k
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
DO NOT start the engine near spilled fuel or combustible
fluids. Fuel is extremely flammable and its vapors can
cause an explosion if ignited.
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
ALWAYS use extreme caution when working with
flammable liquids.
DO NOT fill the fuel tank while the engine is running
or hot.
DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
NEVER use fuel as a cleaning agent.
DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
SAFETY INFORMATION

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 9
TRANSPORTING SAFETY
CAUTION
NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
Always make sure crane or lifting device has been
properly secured to the lifting bail (hook) of the
equipment.
ALWAYS shutdown engine before transporting.
NEVER lift the equipment while the engine is running.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
Use adequate lifting cable (wire or rope) of sufficient
strength.
Use one point suspension hook and lift straight
upwards.
DO NOT lift machine to unnecessary heights.
ALWAYS tie down equipment during transport by
securing the equipment with rope.
Never allow any person or animal to stand underneath the
equipment while lifting.
ENVIRONMENTAL SAFETY
NOTICE
Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
SAFETY INFORMATION

PAGE 10 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
Definition of Tamping Rammer
The Mikasa MTX80/MTX90 tamping rammer is a powerful
compacting tool capable of applying a tremendous force in
consecutive impacts to a soil surface. Its applications include
soil compacting for road, embankments and reservoirs as
well as backfilling for gas pipelines, water pipelines and cable
installation work.
The impact force of the MTX80/MTX90 levels and uniformly
compacts voids between soil particles to increase dry density.
Circular motion is converted to create impact force. The
MTX80/MTX90 tamping rammer develops a powerful
compacting force at the foot of the rammer. To maintain
optimum performance, proper operation and service are
essential.
Construction of Tamping Rammer
The Mikasa MTX80/MTX90 is equipped with an air cooled,
four- cycle gasoline engine. Transmission of the power takes
place by increasing the engine speed to engage the
centrifugal clutch.
Rammer Gearbox and Spring Cylinder
The Mikasa MTX80/MTX90 uses an oil bath lubrication
system. Always check the oil level through the oil level sight
glass at the rear of the tamper foot.
Controls
Before starting the MTX80/MTX90 Tamping Rammer identify
and understand the function of the controls.
GENERAL INFORMATION
Before starting operation check the lifting
handle to:
1. Make sure that there is no damage on the bolts.
2. Make sure that there is no crack or breakage on handle.
3. Make sure that there is no fissure on the surface. If there
is any abnormality or damage, replace with new one.
For operation:
This handle is to be used to lift up the shoe part of the machine
with the body laid down on the ground or truck bed.
1. Use proper lifting techniques to avoid back injury. This
handle is for manual lifting only.
2. Do not use this handle as a rammer lift point. Use the
lifting point on the top of the machine.
3. Do not move the rammer with the lifting handle and the
front rollers more than 16 feet (5 meters).
CAUTION
Handle Operation

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 11
Table 1. MTX80/MTX90 Rammer Specifications
Model MTX-80 MTX-90
Overall Height 39.37 in. (1000 mm) 39.37 in. (1000 mm)
Overall Width 14.37 in (365 mm) 14.37 in (365 mm)
Over Length 31.02 in (788 mm) 31.02 in (788 mm)
Shoe Size 13.4 x 11.2 in (340 x 285 mm) 13.4 x 11.2 in (340 x 285 mm)
Fuel Tank Capacity 3.2 qt. (3 liters) 3.2 qt. (3 liters)
Lubrication Oil Capacity 0.8 quart (0.75 liter) 0.8 quart (0.75 liter)
No. of Impacts Per Second 10.6 - 11.3 11.0 - 11.6
Impact Force 3,080 lb (13.7 kN) 3,530 lb (15.7 kN)
Impact Plate Stroke 2 - 3.15 in (50 - 80 mm) 2 - 3.15 in (50 - 80 mm)
Operating Weight 183 lbs. (83 kg) 196 lbs. (89 kg)
Speed Setting 3400-3600 rpm 3500-3700 rpm
Measured Sound Power Level 105 dB 105 dB
Guaranteed Sound Power
Level 107 dB 107 dB
Max. Sound Pressure Level 95 dB 97 dB
snoitacificepSenignE.2elbaT
ledoMenignE03564D221HEniboR
epyT ,VHO,ekortS4delooC-riA
enigneenilosagrednilycelgnis
tnemecalpsiDnotsiP)cc1
21(.ni.uc4.7
tuptuO.xaM)WK6.2(mpr006,3/ph5.3
metsySgnilooCdelooC-riA
yticapaCliOenignE)retil4.0(.tq24.0
leuFe
nilosagdedaelnU
enignEroftnacirbuL rehgihroESssalC;liOelibomotuA
metsySgnitratSretratSlioceR
epyTgulPkrapSS
E6RBKGN
SPECIFICATIONS

PAGE 12 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
Figure 1 shows the location of the controls and components
for the MTX80/MTX90 Tamping Rammer. The functions of
each control is described below:
1. Combination (Throttle) Lever – Used to adjust engine
speed (rpm). Move lever forward (SLOW) to reduce
engine speed, move lever back toward operator (FAST )
to increase speed. Always operate the rammer at full speed
(rpm).
2. Handle – To operate rammer, GRIP handle assembly
firmly on both sides.
3. Fuel Tank Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Figure 1. MTX80/MTX90 Rammer
4. Hook – Used to lift rammer for transporting.
5. Air Cleaner Cover – Protects the air cleaner which
prevents dirt and other debris from entering the engine.
6. Roller – Used for loading the rammer in back end of a
truck. Rammer is brought to tail gate roller side toward
the truck bed and driver lifts roller with handle at base and
rolls the unit into truck bed.
7. Bellows – Reservoir for oil bath.
8. Foot – Laminated wood with tempered steel plate for
superior shock absorption.
9. Fuel Tank – Holds the fuel for the unit (up to 3.2 quarts)
10. Muffler – reduces the noise of the engine when running.
11. Engine – this unit uses a Robin EH122D46530 gasoline
engine.
12. Oil Gauge (Sight Glass) – Indicates the level of oil in the
oil bath reservoir.
13. Drain Valve – Open this valve to remove oil from the
bellows.
2
1
9
3
4
5
6
7
10
11
12
13
8
COMPONENTS
WARNING
Add fuel to the tank only when the engine is
stopped and has cooled down. In the event
of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been
completely wiped up and the area
surrounding the engine is dry.

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 13
Figure 2. Engine Controls and Components
(Robin EH-12-2D)
The engine (Figure 2) must be checked for proper lubrication
and filled with fuel prior to operation. Refer to the manufacturer's
Engine manual for instructions & details of operation and
servicing.
1. Secondary Air Cleaner – Prevents dirt and other debris
from entering the fuel system. Remove wing-nut on top
of air filter cannister to gain access to filter element.
2. Choke Lever – Used when starting the engine. Normally
used in cold weather conditions. In cold weather turn
the choke lever to the fully closed position, in warm
weather set choke lever half way or completely open.
3. Spark Plug – Provides spark to the ignition system.
Set spark plug gap to 0.024 - 0.028 inch (0.6 - 0.7 mm).
Clean spark plug once a week.
4. Muffler – Used to reduce noise and emissions.
5. Recoil Starter (pull rope) – Manual-starting method.
Pull the starter grip until resistance is felt, then pull
briskly and smoothly.
6. Engine ON/OFF Switch – Controls the starting and
stopping of the engine. Switch must be in the "ON"
position when starting the engine.
BASIC ENGINE
Operating the engine without an air filter, with a damaged air
filter, or a filter in need of replacement will allow dirt to enter
the engine, causing rapid engine wear.
NOTICE
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operating. NEVER operate
the engine with the muffler removed.
WARNING

PAGE 14 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
Rammer Crankcase and Spring Cylinder Oil Bath
This unit uses an oil bath lubrication system.Perform the following:
1. Check the oil level through the oil level sight glass (Figure 3)
at the rear of the tamper foot.
This section is intended to assist the operator with the initial
start-up of the MTX80/MTX90 Tamping Rammer. It extremely
important that this section be read carefully before attempting
to operate the rammer.
DO NOT use your rammer until this section is thoroughly
understood.
2. Check the engine oil level and if the engine oil level is low,
it should be refilled. Low levels of oil may result in engine
seizure. Use the proper motor oil as suggested in the Table
3 below.
Figure 5. Engine Oil Dipstick
Figure 3. Foot Housing Sight Glass
2. If oil is not visible, add 10W-30 SE, SF or higher grade motor
oil into the oil fill plug opening (Figure 3).The bath contains
approximately 1.7 pints (800 cc.)
Figure 4. Fuel Tank
Engine
1. Fill the fuel tank (Figure 4) with unleaded gasoline. At the
same time, check the engine oil and make it a habit to
replenish it often (Figure 5).
edarGliOrotoM3elbaT
erutarepmeTronosaeS liorotomfoedarG
)ssalcSMnahtrehgih(
nmutuAroremmuS,gnirpS
F°51+otF°021+ 03EAS
retniW
F°5
1+otF°04+ 03EAS
F°51+woleB03-W01EAS
SIGHT GLASS
OIL DRAIN PLUG
OIL FILL PLUG
FUEL
TANK
OIL LEVEL
DIPSTICK
OPERATION
Failure to understand the operation of the MTX80/MTX90
Tamping Rammer could result in severe damage to the
unit or personal injury.
CAUTION
The oil level should be kept at the half way point of the sight
glass.
NOTICE

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 15
Inspection
1 . Check all nuts, bolts fasteners for tightness. Retighten as
necessary.
2. Clean any dirt from the recoil starter and foot pedestal. Wipe
the entire unit clean before operating.
3. Replace any missing or damaged Safety Operation decals.
4. Adjust height of handle. Adjust handle by loosening nuts and
moving handle to suit operation. Retighten nuts.
Initial Start-up
When starting the MTX80/MTX90 Tamping Rammer perform
the following:
1. Slide the throttle lever from the stop to the idle position ( )
(Figure 6).This opens the fuel cock and the engine electrical
circuit is turned on automatically.
Figure 6-A. Throttle Lever (Idle {Position)
THROTTLE LEVER
(IDLE POSITION)
3. Place the choke lever to the closed position (Figure 7).When
the weather is cold, close the choke all the way.When it is hot,
or if the engine is hot, open the choke a little or leave it fully
open.
Figure 7. Choke Lever
CHOKE LEVER
(CLOSED POSITION)
5. If engine fails to start, move the choke lever to the half open
position to avoid flooding.
6. Repeat steps 1 thru 5.
7. If the engine does not start after repeated attempts,
check the spark plug for excess fuel.Clean and replace
the spark plug as needed.
4. Grip the starter rope handle (Figure 8) and pull it until you
feel a slight resistance.Then pull sharply and quickly.Return
the handle to the starter case before releasing.
Figure 8. Recoil Starter
STARTER
ROPE
Figure 6-B. Primer Pump
2. Units with Carburetor Primer System: Push the
primer pump bulb four (4) times to deliver fuel to the
carburetor (Figure 5-B).
OPERATION
DO NOT press the primer pump bulb more than four
(4) times, as this will cause fuel to flood the carburetor.
NOTICE

PAGE 16 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
Operation
1. To start the rammer tamping action, move the throttle lever
(Figure 9)
quickly from IDLE to the START ( )position.
DO NOT move the throttle lever slowly as this may cause
damage to the clutch or spring.
Stopping The Engine
Normal Shutdown
1. Move throttle lever quickly from the START to IDLE position
(Figure 10) and run the engine for three minutes at low speed.
After the engine
cools , move the throttle lever to the STOP
position (Figure 11).The engine will stop and the fuel cock
is automatically closed.
2. The MTX80/MTX90 tamping rammer is designed to run at
3,600/3700 rpm. At optimum rpm the foot hits at the rate
between 590 ~ 695 impacts per minute. Increasing throttle
speed past factory set rpm does not increase impacts and
may damage unit. The MTX80/MTX90 is designed to ad-
vance while tamping. For faster advance, pull back slightly
on the handle so that rear of foot contacts soil first.
3. To stop the tamping action, move throttle lever quickly from
START to IDLE position (Figure 10).
Figure 9. Throttle Lever (Start Position)
2. If the engine does not stop due to a problem with the switch
or the like, move the machine to a safe location and hold the
throttle lever in the stop position. Let the machine run on idle
and the machine will stop after a few minutes.
THROTTLE LEVER
(START POSITION)
Figure 10. Throttle Lever (Idle Position)
THROTTLE LEVER
(IDLE POSITION)
Figure 11. Throttle Lever (Stop Position)
THROTTLE LEVER
(STOP POSITION)
OPERATION
Make sure that the throttle lever is moved to the FULL START
position. Operating the rammer at less than full speeds can
result in damage to the clutch springs or foot.
CAUTION

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 17
Maintenance
Perform the scheduled maintenance procedures as indicated:
DAILY
■ Thoroughly remove dirt and oil from the engine and control
area.
■ Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary.
■ Check the spring box and bellows for oil leaks. Repair or
replace as needed.
EVERY 50 HOURS
■ Remove the fuel filter cap and clean the inside of the fuel
tank (Figure 12).
■ Remove and clean the spark plug, then adjust the spark gap
to 0.024~0.028 inch (0.6~0.7 mm).
EVERY 80 to 100 HOURS
■ Remove the air cleaner cover. Loosen and remove the 2
screws that hold the cover to the air cleaner assembly. If the
primary element (Figure 13) is dirty, wash it with gasoline or
kerosene. Then dip it in engine oil (SAE10W-30) and wring
the element so that 25 to 30 cc of engine oil remains on the
element.
Figure 13. Air Cleaner Primary Element
EVERY 200 HOURS
■ Remove the oil drain plug on foot housing (Figure 14) and
drain the oil. Refill with approximately 1.7 pt. (800 cc.) of
10W-30 SE, SF or higher grade motor oil. Oil should be
midway in sight glass. Break in oil should be changed after
first 50 hours.
Figure 12. Fuel Filter
FUEL FILTER
PRIMARY
ELEMENT
SIGHT GLASS
OIL DRAIN PLUG
OIL FILL PLUG
Figure 14. Oil Drain Plug
EVERY 2YEARS
■ Replace the fuel line every 250 hours or every 2 years even
if there is no visible damage.
Long Term Storage
■ Slide the throttle lever to the STOP position.
■ Drain any fuel including in the fuel hose.
■ Replace lubrication oil and apply grease to lubrication
points.
■ Cover the air intake on the air cleaner and the exhaust outlet
on the muffler.
■ Store unit indoors covered with plastic sheet in moisture
free and dust free location out of direct sunlight.
MAINTENANCE

PAGE 18 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)
GNITOOHSELBUORTENIGNE.4ELBAT
MOTPMYS MELBORPELBISSOP NOITULOS
tratsottluciffiD
gulpkrapstubelbaliavasileuF
elbaliavarewoP(.etingitonlliw
.)elbacnoisnethgihta
?egdirbgniebgulpnoitingI .metsysnoitingikcehC
?noitingitatisopednobraC .noitingiecalperronaelC
evitcefedoteudtiucrictrohS
?srotalusni
.srotalusniecalpeR
?pagkrapsreporpmI .pagtcerrocehtotpaggulpkrapsteS
gulpkrapstubelbaliavasileuF
rewoP(.etingitonlliw TON
.)elbacnoisnethgihtaelbaliava
?hctiwspotstatiucrictrohS .evitcefedfihctiwspotsecalpeR.tiucrichctiwspotskcehC
?evitcefedliocnoitingI .liocnoitingiecalpeR
gulpkrapsdnaelbaliavasileuF
noisserpmoc(setingi )lamron .
nobrachtiwdeggolcrelffuM
?stisoped
.relffumecalperronaelC
,retaw(etauqedaniesunileuF
?)tsud
.leufhserfhtiwecalperdnametysleufhsulF
?deggolcrenaelCriA .renaelcriaecalperronaelC
gulpkrapsdnaelbaliavasileuF
noisserpmoc(setingi wol .)
?teksagdaehrednilycevitcefeD .teksagdaehecalperrostlobdaehrednilycnethgiT
?nrowrednilyC .rednilycecalpeR
?esoolgulpkrapS .gulpkrapsnehgiT
.noisserpmocwoL ?tnemtsujdaevlavtcerrocnI .sevlavtsujdadnakcehC
yrotcafsitastonnoitarepO
elbaliavarewophguonetoN
-ssimon,lamronnoisserpmoc(
.)gnirif
?deggolcrenaelcriA .renaelcriaecalperronaelC
?enilleufniriA .enilleufmorf)riaevomer(deelB
?rednilycnistisopednobraC rednilycecalperronaelC
elbaliavarewophguonetoN
-ssim,lamronnoisserpmoc(
.)gnirif
?evitcefedliocnoitingI .leufhserfhtiwecalperdnametysleufhsulF
?strohsnetfogulpnoitingI .noitinginaelc,seriwnoitingiecalpeR
,retaw(etauqedaniesunileuF
?)tsud
.leufhserfhtiwecalperdnametysleufhsulF
.staehrevoenignE
ninoitsopednobracevissecxE
?rebmahcnoitsubmoc
.esacknarcecalperronaelC
htiwdeggolcrelffumrotsuahxE
.nobrac
.relffumecalperronaelC
?tcerrocnieulavtaehgulpkrapS .gulpkrapsepyttcerrochtiwgulpkrapsecalpeR
.tcerrocnideepshgihenignE ?MPRenignetcerrocnI .MPR0063-0043otMPRenignetsujdadnakcehC
TROUBLESHOOTING

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 19
ENGINEENGINE
ENGINEENGINE
ENGINE
deunitnoc(GNITOOHSELBUORTENIGNE.4ELBAT )
MOTPMYS MELBORPELBISSOP NOITULOS
yrotcafsitastonnoitarepO
.setautculfdeepslanoitatoR
?reporpmitnemtsujdaronrevoG .reveltcerrocotronrevogtsujdA
?evitcefedgnirpsronrevoG .noitingiecalperronaelC
?citarrewolfleuF .enilleufkcehC
noitcushguorhtninekatriA
?enil
.enilnoitcuskcehC
gnikrowtonretratslioceR
.ylreporp
?trapgnitatornitsuD .ylbmessaretratsliocernaelC
?eruliafgnirpsgnirpS .gnirpslairpsecalpeR
GNITOOHSELBUORTREMMAR.5ELBAT
MOTPMYS MELBORPELBISSOP NOITULOS
spmujremmartubsnurenignE
..llatatonroyllacitarre
revelelttorhtfodeepsgnitarepO
?tesyltcerrocnisi
.noitisoptcerrocotrevelelttorhtteS
?ssecxeniliO .leveltcerrocotgnirB.liossecxeniarD
?spilshctulC .hctulctsujdaroecalpeR
?eruliaFgnirpS .gnirpslairpsecalpeR
?reporpmienignefodeepS .gnittesMPRgnitarepotcerrocotdeepsenignetsujdA
?detcapmoc-revolioS .liostsetdnaenihcamnwod-tuhS
TROUBLESHOOTING