MuxLab 100507 User manual

© MuxLab Inc. 2020 94-000933-A SE-000933-A
2321 Cohen St, Saint-Laurent, QC Canada H4R 2N7
Tel: [phone] Fax: [phone]
Toll Free (North America): [phone]
E-mail: [email protected] URL: www.muxlab.com
Specifications
Environment
HDMI 2.0a
Devices
Ultra HD Blu-Ray,projectors, monitors, TV, PC, laptops.
Transmission
Transparent to the user.
Video Bandwidth
18 Gbps
Frequency Range
25 to 600 MHz
Signals
HDMI 2.0a protocol.
HDCP
Revision 1.4 & 2.2 compliant.
Connectors
HDMI receptacle.
Rotary Switch
Forsetting theEDID tobe sent to the source
LEDs
Power: Blue
Input & Output Link: Blue
Resolution
480i to 1080p @ 50/60 FPS
1080p @ 24/50/60 FPS
3840 X2160 @ 24/25/30/60 FPS
Color
8, 10 & 12 bit
Audio
LPCM 7.1CH, Dolby TrueHD, Dolby Atmos, DTS-HDMaster
Audio and DTS:X
Cable
HDMI cable of appropriate length for video resolution selected.
Power Supply
One (1) 110-240V/5VDC , 1A power supply
Temperature
Operating: 0° to 40°C Storage: -20° to 60°C
Humidity:up to 90% non-condensing
Enclosure
Metal enclosure
Dimensions
10.62” x 3.93” x 0.94” (270 mm x 100 mm x 24 mm)
Weight
2.4 lbs (1.09 Kg)
Compliance
Regulatory: FCC, CE, RoHS
Warranty
1 year
Order Information
100507 1X8 HDMI Splitter, 4K/60
1X8 HDMI Splitter, 4K/60 (100507)
Quick Installation Guide
Overview
The HDMI 1x8 Splitter (100507) allows one (1) HDMI source to be distributed to
up to eight (8) HDMI displays. The splitter supports up to 4K (3840 X 2160) video
and HD audio. The splitter is HDCP 1.4 & 2.2 compliant, supports EDID
management and features LED diagnostics. Additionally, all connectors are on the
rear panel for neater cabling. Applications include; commercial and residential AV
systems, classroom projector systems, digital signage, boardroom systems,
collaborative PC systems, medical information systems.
Pre-Installation Check
Identify the connectors as indicated on the product diagram above. LEDs are
located on the front and the connectors and mode switch on the rear.
Installation
In order to install the 1X8 HDMI Splitter, please follow the steps below:
1. Connect the HDMI video source to the input HDMI connector of the splitter
with an appropriate HDMI cable.

© MuxLab Inc. 2020
2. Connect the HDMI display equipment to the output HDMI connectors of the
splitter with appropriate HDMI cables.
3. Use the Rotary switch to select the EDID that will be sent to the HDMI source
device as indicated on the Rotary switch table.
4. Connect the 5 VDC power supply to the splitter first, and then plug the power
supply into an AC power outlet.
5. Power on the HDMI equipment and verify the image quality.
6. The following diagram shows the final configuration.
Mode Switch Selection
Use the Rotary switch to select the EDID that will be sent to the HDMI source device.
Position
Function
0
Auto (Mix EDID)
1
EDID Ultra-HD (3840X2160@60Hz) –7.1 Audio
2
EDID Ultra-HD (3840X2160@60Hz) –2.0 Audio
3
EDID Ultra-HD (3840X2160@30Hz) –7.1 Audio
4
EDID Ultra-HD (3840x2160@30Hz) –2.0 Audio
5
EDID Full-HD (1080p, 3D, 12bit) –7.1 Audio
6
EDID Full-HD (1080p, 8bit) –2.0 Audio
7
EDID 1080i –7.1 Audio
8
EDID 1080i –2.0 Audio
9
Learn EDID of the device connected to Output 1 and send it intact to
the input port
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions
in regard to the installation of the 1X8 HDMI Splitter.
Picture/
Sound
Probable Cause
Possible Solution
No Image
Wiring
Check continuity
Check correct wiring
No Image
Synchronization
Power off the source and displays, then power them back on.
Flickering Image
Synchronization
Check HDMI cable length against industry standards.
Choppy Sound
Synchronization
Check HDMI cable length against industry standards.
Noise in image
Weak signal
Check HDMI cable length against industry standards.
Green or pink
hue
HDMI cables
Check HDMI cables and replace as needed.
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or ([phone] (International).