Muzak ENCOMPASS XD User manual

ENCOMPASS XD – QUICK START GUIDE
(LARGE DISPLAY)
The ENCOMPASS XD™is a digital audio playback device that plays audio content directly from a CD-ROM or DVD-ROM.
The system is designed to be virtually “plug and play”. Note that only discs formatted for the ENCOMPASS XD will play.
Consumer audio CDs, CDi and other non-Encompass formatted media will not play in the ENCOMPASS XD.
Your box should include: 1.) ENCOMPASS XD 2.) Power Module 3.) This one-page installation guide
The ENCOMPASS XD includes a back-lit front-panel LCD and five front-panel buttons: POWER, S(UP), T(DOWN), BACK
and ENTER. Should assistance with installation or use of the front panel interface be required, please contact Muzak Network
Operations at 800 327.6549.
ENCOMPASS XD Connections & Settings – Reference diagram on reverse
1 Power
Using the enclosed power module (only), connect the appropriate end to the ENCOMPASS XD rear panel
port labeled 12 VDC IN. Connect the other end into an appropriate 105-130 VAC, 60 Hz, three-prong
power outlet.
2 Audio Output
Using a standard RCA-type audio cable, connect one end to the appropriate ENCOMPASS XD rear panel
RCA-type connector. Connect the other end to an audio amplifier. The Encompass XD supports two
audio zones. The primary zone utilizes the Aoutputs (numbered 1and 3). The secondary zone utilizes
the B outputs (number 2and 4).
3 Time & Date
Press the ENTER button on the faceplate to access the control/diagnostic menu. Press the ▼button once,
then press ENTER to access the Date menu. Press the ▲or ▼button to modify the month. When correct,
press ENTER to move to the next field. The BACK button may be pressed to return to the previous field.
Next, use the ▲& ▼arrows to modify the time zone. Press ENTER to store the time zone. Finally, use the
▲& ▼arrows to confirm the Daylight Saving Time settings. In most cases, this will be YES. If you are in
an area which does not participate in Daylight Saving Time, select NO.
What to Expect
Upon pressing the POWER button, the LCD on the faceplate of the ENCOMPASS XD will illuminate green
and display the Muzak logo with the message Now initializing drive, then the message Now looking for
media. The latter will transition to Please Insert Media. Press the eject button to open the disc tray. Place the
disc on the tray, with the label facing upward. Press the eject button to close the disc tray. After
approximately eight seconds, the unit will begin playing audio. At that time LCD will display the artist name
and song title.

Environmental Operating Conditions & Physical Specifications
Use Indoor
Audio Unbalanced, 10K
Altitude -975’ to 9,900’
Temperature Range 5 o C to 55 o C
Relative Humidity 8 to 90% non-condensing
Weight (without power supply) 5.5 pounds
Dimensions (H x W x D) 4.5" x 6.8" x 8.25"
Power (Supply Voltage) Input: 90-230 VAC, 50/60 Hz Output: +5V/3.5A
Power Consumption 5 watts typical, 25 watts peak (drive spin-up)
Device Approval FCC Class A
Power Supply Approvals FCC, UL, CSA, VDE
Troubleshooting
Under normal operating circumstances, the faceplate LCD will display the artist and song title.The LCD will display Please
Insert Media or Media Removed when no disc is present. Should you insert a disc not properly formatted, it will be ejected
and the display will read Please Insert Media. If any other message is displayed, technical help may be obtained by calling
Muzak NOC at 800 327.6549.
Display Brightness and Contrast
The faceplate LCD may be adjusted for better viewing. To do so, press the ENTER button on the faceplate to access the
control/diagnostic menu. Press the ENTER button a second time to access the Display menu. Press the ▼button to scroll to
LCD Settings. Use the ▲or ▼buttons to modify the Resistance Ratio (brightness). Once the desired level is reached, press
ENTER to adjust the Reference Voltage (contrast). Again, use the ▲or ▼buttons to adjust to the desired level. When correct,
press ENTER to save the new settings.
System Reset
Powering down the player via the front panel POWER button causes the player to go into a “sleep” mode. To perform an
actual hard reset of the player, either disconnect power, or press the rear panel RESET button, followed by pressing the front
panel POWER button.
Program Selection
Some Encompass XD discs may allow the user to select from a list of Program, Schedule or Calendar playback options. To do
so, press the ENTER button on the faceplate to access the control/diagnostic menu. Press the ▼button to scroll to Pgm. Press
the ENTER button to access a listing of available selections. Use the ▲or ▼buttons to scroll to the desired selection. Press
the ENTER button to make your selection.
Note Regarding Date & Time
The time, date and time zone are set by the manufacturer prior to shipping. These should be confirmed upon installation. In
order to provide dayparting or special event programming, some discs require that the date and time be set. Should the
Daylight Savings time setting be set to Yes, the system clock with automatically adjust on the proper date.
Last Updated: 14 October 2005, Version 5.00 / Based on Firmware 5.06