MXN MXN46R-TVI User manual

60.00
3.50
175.78
41.80
±30°Adjustment Range of Camera
Spacer to be selected (1 out of 3), subject to vehicle’s shape
and best alignment of this camera.
60.00
Max 10
91.72
◈MXN46R-TVI Corner Camera
◈Features ◈Technical Specifications
* Design And Specifications Are Subject To Change Without Notice.
Bracket
(top & bottom) Manual
Camera Screw kit
◈Contents
Instruction Manual
Fixation Holder Spacers
(3 types)
HD-TVI 4.0, 1080P/30fps
Video Output
DC 12V, 100mA
Power Consumption 0.5 Lux (50IRE)
Minimum Illumination
Horizontal correction onlyLens Distortion Correction More than 48dB (at minimumAGC gain)
S/N Ratio
Progressive
Scanning System 1080 TV lines
Resolution 2.07 Mega pixels, 1920(H) x 1080(V)
Effective Pixels 1/2.8” Sony CMOS Sensor (STARVIS)
Image Sensor
High Sensitive C-Microphone
Audio Input
-40˚C to +80˚C
Operating Temperature DC 9V ~ DC 48V
Power Range
200˚ (Diagonal), 175˚ (Horizontal), 97˚ (Vertical)
Lens
91.7(W) x 170.5(D) x 42(H) incl. Bracket
Dimensions Approx. 107g (total weight incl. bracket : 290g)
Weight
•2.07 Mega pixels Full HD SONY CMOS Color camera
• 1/2.8” Color CMOS high resolution image sensor (STARVIS)
•HD-TVI 1080P/30fps
•IP69K Waterproof Rating
• Diagonal 200˚ Viewing angle
•Normal/Mirror Image adjustable
•Ultra low light performance
•Automatic Electronic Iris
•Built-in Microphone (for one-wayAudio)
•Temperature Range -40˚C to +80˚C
•Vibration resistant (10G)
•Waterproof screw type connector, 4-pin mini-DIN
•Various spacer type for optimal alignment (0 degree, 8 degree, 15 degree)
•ECE R10.05 approved (EMC)
•ECE R46 Class V and Class VI approved (together with MXN10Q-TVI monitor)
◈Dimensions
Model: MXN46R-TVI
0°Spacer 8°Downward Spacer 15°Downward Spacer
E11
10R-06 11379
E9
04.16273 E9*46R04/08*16273*00
V / VI

Instruction Manual
◈Camera installation and connection (please also check the additional installation instructions)
◈Camera bracket assembling (please also check the additional installation instructions)
MXN10Q-TVI Monitor
or
MXN10-TVI Monitor
(Optional)
MXN46R-TVI
Select 1 of the 3 spacers (to achieve the optimal horizontal alignment out of the
vehicle’s front) and insert the camera into the bottom bracket. Fix the camera with the
fixation holder. The cable and the rubber grommet must be inserted through the camera’s
fixation holder, bulkhead and spacer. The supplied 2 pcs M6 bolts must be inserted
backwards via the bottom bracket through the bulkhead, the spacer and the vehicle’s front.
Before final fixations of the camera, please test & adjust the viewing direction of the
camera to achieve both ECE-R46 Class V field of view and ECE-R46 class VI field of view at
the same moment. Then fasten the fixation holder with the 2 pcs screw firmly.
Run & fix the camera’s cable at the bottom bracket according the drawing details below:
Close the bottom bracket with top bracket.
Insert the supplied screws and fasten the top and bottom bracket each other firmly.
1. Before making the connection, disconnect the ground terminal from the battery
to avoid short circuits.
2. The plugs should be fully inserted into the connectors or jacks.
A loose connection may cause malfunctioning of the unit.
3. A damaged cable may affect the operation of the camera and may even cause
a malfunction of the camera or monitor: Avoid a damaged cable!
4. Protect the cable by using a guide tube, pipe or run the cable inside the vehicle
as much as possible. Caution! Run the cable in natural shapes in order to
prevent cable breaks.
5. Preferably use an acid free grease in between the waterproof screw type
connectors and tighten them firmly each other.
Caution !!
Securing cable connection
Note!
Warranty will not be valid if the problem is related to moist / corrosion in the connector.
1. Match the arrow marks and
press the connectors together. 2. Screw the camera connector up clockwise.
3. Tighten cable connection firmly
in order to prevent water ingress.
* Green loop wire un-cut: MIRROR image
* Green loop wire cut: NORMAL image
The Normal / Mirror image can be changed via the GREEN loop wire:
Normal / Mirror Image adjustment
* Design And Specifications Are Subject To Change Without Notice.
Wiring to Monitor
Run the cable from the camera to the
monitor.
Extension cable
(Optional)
N/C Audio out
Video out Power (9~48V DC)
GROUND
Camera pin configuration
MODEL : MXN46R-TVI
Bolt M6x50L
Nut M6
M6 Plane
Washer
Rubber Ring
Fixation Holder
M3x10L Allen Screw with Washer
M3x10L Allen Screw with washer