My Green Mattress My Green Platform Bed User manual

Assembly Instructions
My Green Platform Bed
Panhead screw (24)
Barrel nut (24)
Hex-key allen wrench (1)
Hardware Included
Hardware Not Included
Phillips-head screwdriver
Align one end board, one right leg, and one left leg
so that pockets are all facing the same direction.
Fit the dowel pins on the end board into the pre-
drilled holes on the legs.
Insert one wood screw into each of the four pocket
holes on the end board.
Use a Phillips-head screwdriver to tighten each
wood screw.
Repeat above steps using the opposite end board,
right leg and left leg.
Step 1.Attach legs to end boards
Wood screw
Twin X-long/Full/Full X-long (8)
Queen/King (12)
Dowel pins
Pocket holes for wood screws
Locate an outside rail marked with a green circle.
Position the rail such that the notches are on top and facing
in toward the middle of the bed frame.
Insert one end of the rail into the notch on one of the legs.
Insert a barrel nut into each of the two pre-drilled holes on
the rail.
Insert a panhead screw into each of the two predrilled holes
on the leg. Be sure screws go through the barrel nuts in the
rail. Tighten the panhead screws by hand for now.
Insert the opposite end of the rail into the notch on the
opposite leg.
Insert a barrel nut into each of the two pre-drilled holes on
the rail.
Insert a panhead screw into each of the two predrilled holes
on the leg. Be sure screws go through the barrel nuts in the
rail. Tighten the panhead screws by hand for now.
Repeat all steps above to attach the second outside rail
marked with a green circle. Ensure that the notches in the
second outside rail are on top and facing toward the middle
of the bed frame.
Step 2. Attach two outside rails
Left leg (2) Right leg (2)
Outside rail (2)
Center rail (2)
Slat with pre-drilled holes (4) Slat without holes
Full (26), Twin X-long/Full X-long/Queen/King (28)
Parts Included
End board (2)
Dowel pins
(pre-installed)
Center support leg (2)
Included with
Queen and King
C
Watch our instructional video on our website:
mygreenmattress.com/product/my-green-platform-bed/

Locate a center rail marked with a blue circle.
Position the rail such that the notches are on top and facing
toward the outer edge of the bed frame.
Insert the rail into one set of notches in the middle of the end
boards.
On one end of the rail, insert a barrel nut into each of the two pre-
drilled holes. Do the same on the other end of the rail.
On one of the end boards, insert a panhead screw into each of the
two pre-drilled holes. Be sure screws go through the barrel nuts in
the rail. Tighten the panhead screws by hand for now. Repeat this
step on the other end board.
Repeat all steps above to attach the second center rail marked
with a blue circle. Ensure that the notches in the second center
rail are on top and facing toward the outer edge of the bed frame.
Locate a slat that has predrilled holes.
Locate a set of notches on the rails that have predrilled holes.
Lay the slat into the notches.
On one end of the slat, insert a barrel nut into the pre-drilled
hole. Do the same on the other end of the slat.
On the outside rail, insert a panhead screw into the pre-drilled
hole. Be sure the screw goes through the barrel nut in the slat.
Tighten the panhead screw by hand for now. Repeat this step
on the center rail.
Repeat all steps above to attach the remaining slats that have
pre-drilled holes.
Step 5.Attach the slats with pre-drilled holes
Attach the remaining slats by inserting them into the
remaining notches on the rails.
No hardware needed.
Step 6.Attach the remaining slats
After all parts of the platform bed are assembled, use the included
hex-key allen wrench to tighten all of the panhead screws.
Re-tighten the panhead screws every six weeks to ensure the bed
remains sturdy.
Step 7. Tighten all panhead screws
Step 4. Attach two center support legs*
*Included with Queen and King sizes only.
Don’t have a Queen or King? SKIP to STEP 5 NOW.
Position one of the center support legs at approximately the
middle of one of the center rails.
Fit the leg and the rail together so that the rail is resting on the
cut-out in the leg.
Insert one wood screw into each of the two pre-drilled holes in
the center support leg.
Use a Phillips-head screwdriver to tighten each screw.
Repeat this step to attach the second center support leg to the
other center rail.
Step 3. Attach two center rails
Center rails
Included with Full,
Full X-long, Queen,
and King sizes only
Center support legs
Included with Queen and
King sizes only