MyBinding SealerSales W-2510H User manual

SealerSales W-2510HT
10" Hand Press Double
Impulse Sealer
Instruction Manual

HAND PRESS DOUBLE
IMPULSE SEALER
OPERATING INSTRUCTIONS
MODEL: W-
2510HT
TROUBLESHOOTING
MALFUNCTIONS REASONS SUGGESTIONS
No sealing
Power lamp is off Disconnected plug Power cord is broken
Transformer is broken
Check or change the plug
Replace or repair the cord
Replace the transformer
No sealing
Power lamp is on
Sealing lamp is on
Heater (heating element) is
broken
Spring hook our mounting
spring is loose or in poor
contact
Terminals of the heating
element are in poor
contact
Replace the heater
Clean or tighten spring
hook connection
Clean the terminals and
adjust if needed
No sealing
Power lamp is on
Sealing lamp is off
Microswitch is activated
Defective microswitch Adjust the microswitch
lever
Adjust the microswitch
position
Replace the microswitch
Teflon cloth burn Timer malfunction
Prolonged heating time Replace timer or relay Decrease the timer
setting
Heating wire breaks Worn Teflon adhesive Replace the Teflon
adhesive
Seal is wrinkled Heating timer is set too
high
Cooling time is not enough
Lower the timer setting
Continue pressing the
upper lever for 1-2
seconds after the light
goes off
Imperfect seal Worn Teflon cloth
Worn silicone rubber Replace Teflon cloth Replace silicone rubber
Broken seal Prolonged sealing time Decrease timer setting
Non-full-weld seal Sealing time is too short Increase sealing time
Seal sticking Dirty Teflon cloth
Dirty sealing bar Clean the Teflon cover Clean the silicone rubber
sealing bar

OPERATING INSTRUCTIONS
Beforeoperating, check the heating element, Teflon cover,
Teflon adhesive and sealing pad (silicone rubber).
MAINTENANCETIPS
1. Set the Power Switch to the ON position.
2. Choose either “Single-Wire”or “Double-Wire”sealing.
Single wire will utilize only one element to seal and
double wire will utilize both top and bottom elements to
seal your material.
3. Adjust the timer setting according to the thickness of the
sealing material. Note: Always start with the lowest
setting and gradually increase to the correct setting.
4. Place the object to be sealed.
5. Pull the handle down and seal.
6. Wait2-3 seconds to allow the seal to set and lift the
handle.
Always keep the sealing platformclean and remove any
residue found on the upper barrier (Teflon Cover) and
Pressing Pad (Silicone Rubber).
A good rule of thumb is to replace the bottom barrier tape
(TeflonAdhesive) when replacing the Heating Element.
The Teflon serves as a barrier between the metal seal
arm and the heating element. Never allow the element to
come in contact with the sealer arm as this will damage
the timer.
Be sure to turn OFF the power or unplug before replacing
any parts.
Clean the sealing platform with a dry cloth. Do not use
water or solvents. Use silicone spray.
IMPORTANT POINTS TO REMEMBER
Read all instructions before use. Save these instructions for later
use.
Followall warnings and instructions marked on the product.
Unplug this product from the power source beforecleaning and/or
changingany parts
Do not rest anything on the power cord. Do not place the machine
where the power cord may be stepped on or pulled.
Always keep out of reach of children and pets.
This sealer should only be in use with an operator in attendance.
Never insert clothing, hands, fingers between the sealing jaws of
sealers.
Never touch the heating elements with bare hands while the
sealer is pluggedinto a power source, or in operation, or just
finishedoperation. It will be HOT.
Be sure to check for worn parts before starting operation.
Do not operate with a damaged power cord or plug.
Always keep the unit clean. Do not use water. Siliconespray may
be used to clean the unit. Be sure the unit is unplugged from the
power source before cleaning.
Whenchanging blade (for sealers with cutters), be careful of the
sharp edge.
Whenchanging the teflonadhesive, be sure the entire surface
under the heating element is coveredwith a teflonadhesive.
Bend down the excess teflonadhesive on both ends. This
preventsthe heating element from breaking and the machinefrom
grounding.
Whenreplacing the fuse, be sure the exact voltageand ampere is
used.
Be sure to keep a record of your model number. Specifythis
number when ordering parts.
Whenreplacing any parts, be sure to mark down the exact
locationsof the connections.