MyBinding SealerSales W-300DAT User manual

SealerSales W-300DAT
12" Table-Top Direct Heat Sealer
w/ PTFE Coated Meshed Seal
Instruction Manual

Table-Top Direct Heat Sealers
Models: W-300DAT, W-300DATS
Distributed By:
Version 1.0_2014

General Information
Thank you for purchasing our W-Series Direct Heat Sealers.
This owner’s manual contains information relating to your sealer. The manual will provide you
with basic information concerning both operation and maintenance of your new machine. Please
read it carefully as failure to do so may result in bodily injury and/or damage to the equipment.
Please fill in the information below. You will find the information on the machine identification
plate. You will need this information when ordering replacement parts or making technical
inquiries.
No part of this manual may be duplicated, reproduced, stored in a retrieval system, translated,
transcribed, or transmitted in any form without the express prior written permission of Sealer Sales.
W H D H E Q U I P M E N T I N F O R M A T I O N
Model #
Serial #
Purchase Date:
Reference # (found on packing slip)
Owner:

W H D H I N S T R U C T I O N M A N
Safety Instructions
understood prior to setting up or operating your equipment. Read and fully understand all instructions and
warnings prior to using this unit. Your safety is most important! Failure to compl
result in serious injury or property damage. Remember:
Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to
follow these safety rules
and take necessary precautions can result in serious injury as well as damage to
equipment.
Never operate or service your sealer until you have read this manual completely and understand it
fully.
Plug the sealer into a standard 120 Volt, 60Hz wall outlet
Do not use the sealer if the power cord, plug or any other parts are damaged. Be sure not to allow
the power cord to drape into your work area. Check that all parts are operating properly and
perform the intended functions.
other conditions that may affect the operation.
Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before
connecting
to the power source.
Always disconnect
sealer from power source before servicing, changing accessories or cleaning the
unit.
To provide protection against the risk of electrical shock, the power connection must be properly
grounded at all times.
Do not leave the sealer unattended when in use.
before leaving the work area.
Sealer
is used solely for sealing thermoplastic materials. Using the machine for any other purpose
can cause damage to the machine and operator.
While operating machinery, wear cl
external items from getting caught in the machine. Do not wear jewelry when operating the sealer.
W H D H I N S T R U C T I O N M A N
U A L
2
Safety Instructions
Below are general safety precautions and warnings that should be
understood prior to setting up or operating your equipment. Read and fully understand all instructions and
warnings prior to using this unit. Your safety is most important! Failure to compl
y with procedures may
result in serious injury or property damage. Remember:
Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to
and take necessary precautions can result in serious injury as well as damage to
Never operate or service your sealer until you have read this manual completely and understand it
Plug the sealer into a standard 120 Volt, 60Hz wall outlet
or surge protector.
Do not use the sealer if the power cord, plug or any other parts are damaged. Be sure not to allow
the power cord to drape into your work area. Check that all parts are operating properly and
perform the intended functions.
Check fo
r any worn parts before starting operation.
other conditions that may affect the operation.
Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before
to the power source.
sealer from power source before servicing, changing accessories or cleaning the
To provide protection against the risk of electrical shock, the power connection must be properly
Do not leave the sealer unattended when in use.
Disconnect the sealer from the power source
before leaving the work area.
is used solely for sealing thermoplastic materials. Using the machine for any other purpose
can cause damage to the machine and operator.
While operating machinery, wear cl
ose-
fitting clothing and tie back long hair to prevent any
external items from getting caught in the machine. Do not wear jewelry when operating the sealer.
Below are general safety precautions and warnings that should be
understood prior to setting up or operating your equipment. Read and fully understand all instructions and
y with procedures may
Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to
and take necessary precautions can result in serious injury as well as damage to
Never operate or service your sealer until you have read this manual completely and understand it
or surge protector.
Do not use the sealer if the power cord, plug or any other parts are damaged. Be sure not to allow
the power cord to drape into your work area. Check that all parts are operating properly and
r any worn parts before starting operation.
Check for all
Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before
sealer from power source before servicing, changing accessories or cleaning the
To provide protection against the risk of electrical shock, the power connection must be properly
Disconnect the sealer from the power source
is used solely for sealing thermoplastic materials. Using the machine for any other purpose
fitting clothing and tie back long hair to prevent any
external items from getting caught in the machine. Do not wear jewelry when operating the sealer.

W H D H I N S T R U C T I O N M A N U A L
3
Never touch the sealing bars with your bare hands while the sealer is plugged into a power source,
in operation or just finished operation. Touching heated areas may cause fire and/or severe burns.
While machine is in operation, do not place fingers, tools, or other foreign objects on or into the
machine. Do not place hands or fingers near pinch points. Do not touch machine while it is in
operation. Perform all procedures carefully and watch where hands and fingers are at all times.
The sealer is not water resistant or water proof. Spraying down the machine will damage machine
or cause electrical shock. Do not submerge the sealer into water or liquid.
Do not operate sealer in a corrosive or humid environment.
Always keep the machine clean, lubricated and in good working condition. Follow any
maintenance and lubrication procedures outlined in this manual. Make sure unit is disconnected
from power source before cleaning.
NEVER use any accessories or parts from other manufacturers. Machine should not be altered or
modified using parts that are not genuine authorized parts. Doing so will VOID YOUR
WARRANTY.
Never leave the sealer unattended. Be safe, disconnect the sealer from power source before
leaving work area.
Always keep out of reach of children and pets.
Close supervision is necessary when any appliance is near persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge . This sealer is NOT to be used by
children or by persons with reduced physical, sensory or mental capabilities or lack of experience
and knowledge.
DO NOT use the sealer outdoors.
DO NOT use the sealer while under the influence of drugs, medications or alcohol.
SAVE THESE INSTRUCTIONS - REFER TO THEM OFTEN AND USE THEM
TO INSTRUCT OTHERS.

4
Introduction
W-Series Direct Heat Sealers are designed for sealing many different types of thermoplastic materials
including: coated aluminum foil, Kraft paper, cellophane, polypropylene, poly-nylon, and other thicker
materials up to 20mil in total thickness. Please note that our direct heat sealers would not be appropriate
for sealing polyethylene and/or polyvinyl chloride.
Features of the W-Series Direct Heat Sealers
Your Direct Heat sealer is equipped with a wide range of standard features and capabilities.
Direct heat sealing / constant heat sealing system
Heavy duty all metal construction
Table top design supported with anti-slip rubber feet
Simple to use - minimal operator training
German manufactured temperature controller that maintains the seal bars at a proper temperature
providing consistent seal quality
Electronic timer (0-6 seconds) to adjust sealing time providing for consistent seal quality
Equipped with protector bars around the sealing bars to prevent injury
Hands free sealing activated by footswitch
Sealing width: 1/2" (15mm)
Sealing length: 12" (300mm)
Adjustable work table
Options: meshed (W-300DAT) or serrated (W-300DATS) sealing bars
Figure 1. Meshed seal line Figure 2. Serrated seal line

5
How Do W-Series Direct Heat Work?
Our W-Series direct heat sealers maintain constant heat in both sealing jaws.
Direct heat sealers consume power as long as the sealers remain on thus providing
better heat penetration than impulse sealers. The temperature and length of the
seal time will depend on the characteristics of the bag being sealed. The sealing
process is simple: The operator places material on lower sealing bar of sealer and
activates foot switch to bring the upper sealing bar down. Upper sealing bar will release automatically
based on timer settings.
Specifications
W
-
300DAT W
-
300DATS
Power 110V/60Hz 110V/60Hz
Watts 350W 350W
Seal Width 15mm 15mm
Sealing Length 12" 12"
Seal Type Meshed Serrated
Temperature Range
Dimensions 13" x 14" x 7" 13" x 14" x 7"
Shipping Dimensions 17" x 15" x 16" 17" x 15" x 16"
Net Weight 33lbs 33lbs
Gross Weight 38lbs 38lbs
Basic
Principles
Place material on lower
sealing bar. Activate
foot switch to bring
upper seal bar down.

6
Getting to Know your Direct Heat Sealer
Figure 3. W-Series Table Top Direct Heat Sealer Overview
Temperature Controller
Adjust temperature
depending on material Power Switch
Turn on when you are
ready to use your sealer
Sealing Timer
Adjust sealing time
based on material to be
sealed (0-6 secs)
Foot Switch
Press foot switch to
activate sealing process
Protector Bars
Bars protect operator
from the sealing bars
Lower Sealing Bar
Place material to be
sealed on lower sealing
bar
Working Plate / Table
Remove screws to install
the wo rki ng plate and
table

7
Electrical Circuit Diagram
Figure 4. Electrical Circuit Diagram for W-Series Direct Heat Sealers

Operating your
Assembly Instructions
1.
Connect the footswitch to the sealer unit.
2. To install the
optional working plate and table
install the working plate. Adjust working table heigh
Figure 5. Working Plate and
Operation
1.
Before operating,
are clean and without residue.
2.
Insert the power cord into the correct receptacle (110V).
3. Turn the power switch on.
4.
Set the sealing temperature on the temperature controller depending on the material to be sealed.
(Note:
Temperature on the dial is Celsius, not
temperature setting and gradually increase the temperature as needed.
the sealer to reach the
set temperature.
when the unit has reached the set temperature.
5.
Set the timer setting for the length of the sealing t
material to be sealed and temperature set on the temperature controller.
6. Place material to be
sealed on the lower sealing jaw and press the footswitch to activate the
sealing process. The upper sealing bar will release once seal time is achieved.
8
Operating your
Sealer
Assembly Instructions
Connect the footswitch to the sealer unit.
optional working plate and table
, remove screws located
at the front of the unit and
install the working plate. Adjust working table heigh
t to your bag specifications.
Table Installation
Before operating,
check for any worn parts of the
sealer. Make sure the sealing bars
are clean and without residue.
Insert the power cord into the correct receptacle (110V).
Set the sealing temperature on the temperature controller depending on the material to be sealed.
Temperature on the dial is Celsius, not
Fahrenheit
.) Always start with a lower
temperature setting and gradually increase the temperature as needed.
Allow 5
set temperature.
The light above the temperature contr
when the unit has reached the set temperature.
Set the timer setting for the length of the sealing t
ime. Adjust seal time
material to be sealed and temperature set on the temperature controller.
sealed on the lower sealing jaw and press the footswitch to activate the
sealing process. The upper sealing bar will release once seal time is achieved.
at the front of the unit and
t to your bag specifications.
sealer. Make sure the sealing bars
Set the sealing temperature on the temperature controller depending on the material to be sealed.
.) Always start with a lower
Allow 5
-10 minutes for
The light above the temperature contr
oller will turn off
as needed based on
sealed on the lower sealing jaw and press the footswitch to activate the
sealing process. The upper sealing bar will release once seal time is achieved.

7.
When sealer is not in use, turn off the power switch
Please note: Sealing bars will be extremely hot. Do not touch the
sealing bars as this could cause severe burns.
Tips for Successful Sealing
1.
If the seal is broken or dam
2. If the seal is not fully we
lded, i
3.
If the sealing material sticks to the
4.
Always keep the sealer clean. Remove any residue found on the
used.
5. Be sure to turn
off the power or unplug the unit before replacing any parts.
9
When sealer is not in use, turn off the power switch
.
Please note: Sealing bars will be extremely hot. Do not touch the
sealing bars as this could cause severe burns.
Tips for Successful Sealing
If the seal is broken or dam
aged, decrease the sealing time / temperature.
lded, i
ncrease the sealing time / temperature.
If the sealing material sticks to the
sealing bars, decrease the sealing time / temperature.
Always keep the sealer clean. Remove any residue found on the
sealing bars. Silicone spray may be
off the power or unplug the unit before replacing any parts.
sealing bars, decrease the sealing time / temperature.
sealing bars. Silicone spray may be
off the power or unplug the unit before replacing any parts.

Maintenance
The following maintenance procedures should be followed to ensure the longevity of your
Direct Heat Sealer.
Inspection and Cleaning
1.
Inspect your machine daily.
2. Make
sure the unit is not left on when not in use. Never leave unit on overnight. This will
shorten the life of the parts.
3.
Find the lowest temperature that will still seal the bag.
4.
Use a clean cloth to remove any plasti
using
silicone spray to clean. Spray the silicone spray onto a shop cloth or toothbrush. Wipe
down the sealer when the sealer is turned off and coo
directly on the unit.
Replacement Parts
Before changing any parts, turn off and unplug sealer.
Please make sure parts purchased are from an authorized distributor of W
10
The following maintenance procedures should be followed to ensure the longevity of your
Inspection and Cleaning
Inspect your machine daily.
sure the unit is not left on when not in use. Never leave unit on overnight. This will
shorten the life of the parts.
Find the lowest temperature that will still seal the bag.
Use a clean cloth to remove any plasti
c residue remaining on
the sealing bars.
silicone spray to clean. Spray the silicone spray onto a shop cloth or toothbrush. Wipe
down the sealer when the sealer is turned off and coo
l to touch
. Never spray the silicone spray
Before changing any parts, turn off and unplug sealer.
Please make sure parts purchased are from an authorized distributor of W
-
Series sealing equipment.
The following maintenance procedures should be followed to ensure the longevity of your
W-Series
sure the unit is not left on when not in use. Never leave unit on overnight. This will
the sealing bars.
We recommend
silicone spray to clean. Spray the silicone spray onto a shop cloth or toothbrush. Wipe
. Never spray the silicone spray
Series sealing equipment.

11
Replacing Heater (s)
Our W-Series Direct Heat Sealers will require new heaters from time to time. There are two heaters found
on the unit, one in the upper sealing jaw and one in the lower sealing jaw.
Remove the old heater on either the top and/or bottom sealing jaw. Unscrew the heater loose from the
sealing jaw and base of sealer. Remove the thermostat plate to access the other end of the heater. We
suggest marking down the exact locations of the connections in order to accurately replace the new heater.
Note: In order to the fully remove and install the heater one may also need to separate the head of the sealer
from the base.
Figure 6. Loosen screws found on sealing jaw. Figure 7. Remove thermostat plate.
To install new heater, remove the old heater and crimp on the new heater. Following your marked
connections, install the new heater back on the sealing bar and screw to tighten back into place.
Replacing Thermostat
1. To remove the thermostat, remove the thermostat cap and four screws from the thermostat
control plate. Then, remove the two screws attaching the thermostat plate to the control panel.
Figure 8. Remove thermostat cap. Figure 9. Remove two screws attaching thermostat plate to the control panel.
2. Unplug the two connections from the thermostat base.

12
3. Unscrew the heaters from the bottom sealing jaw in order to remove the thermostat sensor from
the sealing jaw. Note: In order to fully remove and install the thermostat, one may also need to
separate the head of the sealer from the base.
Figure 10. Unplug two connections from thermostat base found
inside sealer head
Figure 11. Unscrew heaters from bottom sealing jaw
Replacing Timer
1. Unscrew the two screws found on the timer. Remove the timer from the base of the sealer.
2. Unplug the timer and replace with new timer.
Figure 12. Remove the old timer Figure 13. Replace with new timer.

13
Parts Diagram
Figure 14. Spare Parts Diagram Overview

14
Item Part # Description Comments
1 WHDH-1 Control Set Bracket
1a WHDH-1a Bolt/Washer to attach control unit to body M6x25
2 WHDH-2 Upper Bracket/Jaw (same as W-300T, but with holes)
2a WHDH-2a Bolt and Washer for attaching the Upper Jaw/ Lower Jaw to the Seal Bar M6 x 30
2b WHDH-2b Bolts (Washer and Nuts) to attach Upper Jaw to Control Unit
WHDH-1/2 Control Set Bracket (#1) and Upper Jaw (#2) and accompanying screws
3 Upper PTFE Coated Seal Bar
sold as pair only - WHDH-3A / 3B
4 Lower PTFE Coated Seal Bar
sold as pair only - WHDH-3A / 3B
3A WHDH-3A PTFE Coated Sealing Bar, Pair, Meshed
3B WHDH-3B PTFE Coated Sealing Bar, Pair Coated, Serrated
5 WHDH-5 Rubber Foot
6 WHDF-6 Pressing Spring, Small W-00403
7 W-300T-12 Pressing Spring, Large (W-300T and W-300DAT)
8 TMC-WHDH Thermostats (E.G.O) E-010
9 WHLH-7 Power Switch, 3P, 15A/125V (W-Series)
10 WHI-11a Circuit Breaker, 7A, W-350I and W-300DAT(S)
11 WHDH-11 Heater Element, 1 piece E-92302
Heater/Element, 2piece Set
11b WHDH-11B Screw for Attaching the Heater to the Seal Bar
12 T-W300DAT/S Timer Set SH2-Y(6S) E-009A
13 FS-WH Foot Switch, 6.5 feet E-011
13a MSWF-WH Microswitch for Foot Switch
14 WHDF-20 Working Table - 13 1/2" x 7" (W x L)
WHDF-19 Working Adjusting Plate - 6 1/4" x 9 1/2" (W x L)
15 PWC-WH Power Cord
16 WHA-33 Lamp (R), LED for E.G.O. E-00302 for (W-Series)
17 WHDH-17 Fiber Plate
18 WHA-38 Solenoid (Electromagnet) TF-281 (2 for AA models)
19 WHDH-19 Rectifier DCBR68
20 WHDH-20 Protector Bar / Isolated Plate / Top of Upper Seal Bar (old #22) - 12 1/4" x 2"
20a WHDH-20a Support for Protector Bar
20b WHDH-20b Screw for Upside Protector Bar
21 WHDH-21 Silicone Washer (big)
22 WHDH-22 Shaft of Pole
23 WHDH-23 Protector Bar / Isolated Plate / Upper Sealing Bar (old #22B) - 12" x 1" (holes - 1/2")
23a WHDH-23a Screw for Bracket for Protector Bar/Isolated Plate Lower Bar & Upper Bar 4/set
24 WHDH-24 Fixed Plate (upside) / Protector Bar Bracket
25 WHDH-25 Control Panel
26 WHDH-26 Silicone Washer (small)
27 WHDH-27 Protector Bar / Isolated Plate / Lower Sealing Bar (old #22A) - 12" x 1" (holes - 1/8")
28 WHDH-28 Fixed Plate (downside) / Protector Bar Bracket
29 WHDH-29 Bushing (Upper Bracket)
30 WHDH-30 Connected Plate / Shaft Plate
31 WHDH-31 Rubber Foot w/ Screw and Nut
32 WHDH-32 Fixed Bracket (spring)
33 WHDH-33 Upper Bracket (Tension Spring)
34 WHDH-34 Sucking Plate
35 WHDH-35 Tension Spring
36 WHDH-36 Bottom Bracket (Tension Spring)
30-36 WHDH-30-36 Tension Shaft Unit (Parts #30-#36)
37 WHDH-37 Base
38 WHDH-38 Joint (Foot Switch)
39 Screw-M4x8 M4*8 Screw
Figure 15. Spare Parts Diagram List

15
Troubleshooting
Problem Possible Causes Solution
Upper and/or lower sealing bars
not heating 1. Heater(s) are worn out. 1. Replace heaters(s) on the unit.
Unit does not heat up (both jaws are
not heating up)
1. Heater(s) are worn out.
2. Temperature controller is worn out.
1. Replace heaters(s) on the unit.
2. Replace temperature controller
Temperature controller will not
stay at set temperature (i.e.
temperature set at 150 but
temperature keeps going up)
1. Temperature controller is worn out.
2. Thermocouple is worn out (rare
occasion).
1. Replace temperature controller.
2. Replace thermocouple.
Sealing jaw not activating
1. No power to the unit.
2. Timer is worn out.
3. Solenoid needs replacement.
4. Footswitch needs replacement.
1. Check power source.
2. Replace timer.
3. Replace solenoid.
4. Replace footswitch.