MyGate PTP45 Series User manual

PTP45
PTP45 20 - PTP45 30 - PTP45 50
PTP45 50M
Automation for blinds and awnings
Installation manual
rev01_21

01
......................................................................................................................................... p.
2.1
1.
Index
2. DESCRIPTION AND INTENDED USE
Technical data
2.3 Kit content
3. INSTALLATION
Limit switch in closing
Limit switch in opening
2.4 Dimensions
3.3
3.2.1
3.2.2
SAFETY INSTRUCTIONS
3.1
3.2
Wiring
Limit switch setting
4. WARRANTY
5. MAINTENANCE
6. DISPOSAL
2.2 Selection guide
7. ERROR MESSAGES
8. COMPLIANCE DECLARATION
Awnings
.................................................................................................................... p. 02
.................................................................................................................... p. 02
.................................................................................................................... p. 02
.................................................................................................................... p. 03
.................................................................................................................... p. 03
.................................................................................................................... p. 04
.................................................................................................................... p. 06
.................................................................................................................... p. 06
.................................................................................................................... p. 06
.................................................................................................................... p. 07
.................................................................................................................... p. 07
.................................................................................................................... p. 08
.................................................................................................................... p. 08
.................................................................................................................... p. 08
.................................................................................................................... p. 08
.................................................................................................................... p. 08
rev01_21

1
WARNING
This manual contains important information concerning personal safety: children aged 8 or
more and/or people with reduced physical, sensory or psychic abilities are allowed to use the
automation if under supervision or duly instructed on possible risks and danger.
Children are forbidden to play with the automation.
Maintenance and cleaning may be performed by children only under supervision. Frequently
check possible sign of waste and damage (wires and supports).
Do not use the automation if repairing is needed or if maintenance is in progress
(ex: windows cleaning).
Important safety instructions for people, READ CAREFULLY when you see this symbol:
Use and installation of the product must comply with Machinery Directive 2006/42/CE.
Installation must be carried out by expert qualified personnel who knows the potential hazards
associated and in full compliance with current regulations. Use of the product must be restricted
to its intended use. Any other use is to be considered dangerous and therefore forbidden.
Keep any remote control device (i.e. transmitters) away from children,
to prevent the automation from being accidentally activated.
Keep the automation regularly maintained. Use only Proteco's original spares. Users are
strictly forbidden to carry out any changes on the system. Proteco Cancelli Automatici Srl is
not liable for any damage resulting from improper, wrongful or unreasonable use.
1.1. SAFETY INSTRUCTIONS
Installation has to be powered through an all-pole disconnection switch
Switch the power OFF before any operation.
Before proceeding to installation, remove any useless wires and/or
components. The characteristics of the area to be automated have to match
the automation capacity in terms of load and working time.
Make sure the main power line is equipped with state of the art safety ground
system. If the power line wire is wasted inform the Manufacturer or contact an
authorized service center for replacement.
rev01_21

PTP45 30 30
PTP45 50
50
PTP45 20 20 32 Kg
52 Kg
90 Kg
PTP45 50M
2.5 3.5 4 5.25 7 8 9.5 15
PTP45 30 PTP45 50 N.A.
6Kg/m²
9,5Kg/m²
PTP45 20 PTP45 30 PTP45 50
PTP 45 20
MAX m²
PTP45 30 PTP45 50 N.A.
12,5Kg/m² PTP45 20
The PTP45 range is designed to automate blinds and awnings.
2.1 TECHNICAL FEATURES
1 2
2. DESCRIPTION AND INTENDED USE
PTP4520
Thrust
Motor Speed
Motor Power
Current
Weight
Length
PTP4530 PTP4550 PTP4550M
2.2 SELECTION GUIDE
Surface calculation:
height x width =
select the model according to
the table below
m2

V

MATERIAL
del N
Ø70 mm tubolar motors
Intersect the value of the extension
with the number of arms of the awning
EXTENSION OF ARMS
N° ARMS
Noise level
50
13
244
1,06
3,30
620
50
13
244
1,06
2,40
480
30
17
226
0,95
2,35
480
20
17
155
0,68
2,30
440
Nm
rpm
W
A
Kg
mm
LpA ≤ 70 dB(A)
rev01_21

PTP45 20 – PTP45 30 – PTP45 50
PTP45 50M
1
2
3
4
1
2
3
4
5
2.4 DIMENSIONS
3
2.3 KIT CONTENT
PTP 45 (without emergency release)
1
2
3
4
5
6
7
PTP 45 M (with emergency release)
01
02
03
04
n°1
n°1
n°1
n°1
Tubular motor
Limit switch adjuster wrench
Split pin
Wall fixing support
01
02
03
04
05
n°1
n°1
n°1
n°1
n°1
Tubular motor
Limit switch adjuster wrench
Wall fixing support
Split pin
Release key
rev01_21

Before installing make sure the power supply is OFF. If you need to replace ang system, remove all devices for
manual opon.
In case of an it is possible to keep the same octagonal adapter 60mm.
1- Low down the roller blind and disconnect it from the octagonal tubular (Picture A).
2- Remove the octagnal tubular (Picture B).
RECOMMENDED TOOLS:
3 4
3. INSTALLATION
Make sure the command keys are posioned where the system can be visible during operaon and at a
minimum ground height of 1,5m.
Make sure manual operation devices are posioned at least at a minimum ground height of 1,8 m.
Picture A
Picture B
rev01_21


.
3 - Measure the distance between the two supports (L). Fit
the 60 mm octagonal tubular in for the whole length 
covering the locking ring of the limit switch (Picture C).
4- The length of the octagonal tubular must be such to get the total length (L) as shown in the below picture,
keeping a clearance of 2-3 mm. In order to check the correct  and to simulate the final inon, lay
temporarily the support to the wall as shown in the picture.
5- 
alignment between the two fixing supports and check that the
octagonal tubular is on level. Mark the holes of the fixing support
in a way to get easy access to both fixing screws.
Proceed to fix the support to wall.
5
Picture D
Picture B Picture C
6- Complete the assembling locking the system with the
provided split pin.
rev01_21

CLOSE
on! During manual opon we recommend to keep the limit switch screws
in downwardon.
3.1 WIRING
Wire the system according to the below diagram:
To be up to safety standards we recommend to fit a power cut device, keeping a
minimum distance of 3 mm between the contacts. Every motor has to have its own device.
WIRES KEY:
1
2BROWN
3B)
4

If you wish to install the motor at your right, just switch the black wire with the brown.
It’s always wise to double check the wiring: if thon should not proper, just switch the poon between
the black and the brown wires.
3.2 LIMIT SWITCH SETTING
3.2.1 LIMIT SWITCH IN CLOSING
g the store/awning make sure the motor is properly mounted inside the octagonal tubular as
well as the limit switch trolley. Now let the motor run downing the expected end stop pon
activated by the limit switch. Then fit the store to the octogonal tubular.
5 6
Wiring diagram for motor installed at your left
OPEN/CLOSE
OPEN
rev01_21

3.2.2 LIMIT SWITCH IN OPENING
Give an opening command. Chon and make the according adjustments if necessary.
To set the limit switch, plug the provided key into the according fixing points. If you wish to increase the run of
the store/awning, turn to “+”, while if you wish to decrease it turn to “-“.
The below diagrams show how to adjust the available systems, opening
(possible adjustments for RH and LH motor):
3.3AWNINGS
Ø 70 adapters are available for awnings. Item code PTPR01W.
So far the assembd the awning manufacturer’s instruons.
So far the wiring and limit switch adjustmentrefer to the store inon manual.









PROTECO Srl Via Neive 77, 12050 Castagnito (CN) Italia
The warranty doesn’t respond when:
7
4. WARRANTY







PTP45 20/30/50
PTP45 50M
CLOSING LSCLOSING LS
OPENING LSOPENING LS
CLOSING LS
OPENING LS
CLOSING LS
OPENING LS
rev01_21

5. MAINTENANCE


6. DISPOSAL
DO NOT DISPOSE OF IN NATURE!


7 8
7.ERROR MESSAGES
THE MOTOR
DOESN'T WORKTHE
MOTOR
EFAULTROR CHSOLUTIONECK:
•Double check the motor's wiringg
•Double check the motor doesn't overheat
THE MOTOR STOPS
BEFORE THAN
EXPECTEDEM STOPS
TOO SOON
•Double check the limit switch operation during motor's running
•Double check the limit switches work properly
THE MOTOR
DOESN'T STOPOP
•Double check the limit switch crown has been correctly inserted into
the motor5)
rev01_21