MySound BH-03 User manual



1

User’s manual
BH-03
Bluetooth stereo Headset







SPECIFICATIONS
Model no BH-03 Ver. Bluetooth V2.1+EDR
Bluetooth Profiles HSP,HFP,A2DP,AVRCP Effective Range 10Meters
Music Time 10 Hours Talk Time 11Hours
Standby Time Up to 250 Hours Iuput DC : 5V/160mAh
Charge Time 4~4.5 Hours Dimensions 14.5*10*6CM




2

About BH-03
BH-03 is a stereo headset with Bluetooth technology. It supports the following Bluetooth
profiles:
HSP —— Headset Profile
HFP —— Hands-free Profile
A2DP—— Advanced Audio Distribution Profile
AVRCP——Audio/Video Remote Control Profile
Overview

1 + key: Volume Up
3 > key :next song 2 Multifunction Buttom answer, end and
reject call, pause and play
4 –key: volume down 5 Charging port
6 Built-in microphone 7 LED Indicator
8 <key :last song 9 Folding
10 Bettery Indicator LED 11 Bettery Check
Charging the battery with USB cable
•Step1: Insert USB charging cable into USB port of PC.
•Step2: Connect charging cable with the charging port of headset.
•When the red light is on, the headset is charging.
•When the blue light is on, the headset is charged fully.



3

•It takes about 3 hours to charge the headset fully.
Warning:
•The battery is rechargeable.
•First time charging : Before you use this Bluetooth headset, please charge the battery
of headset fully
How to use
A Switching on / off headset
Function Operation LED indicator Indication tone
Switch on Press and hold the
MFB for 3 seconds Blue LED is on for 1 second “Do Do Do” tone
Switch off Press and hold the
MFB for 6 seconds Red LED is on for 1 second “Do Do DO” tone
B Pairing the headset with Bluetooth devices
A) How to enter pairing mode
Be sure BH-03 in power off status first. Press and hold the MFB for 6 seconds, till Red
and blue Led blink alternately, or you hear the indication “Do Do” twice come out. And then
release the MFB. The unit will become pairing mode.
B) Pairing the headset with Bluetooth mobile phone
Please make sure your mobile phone has Bluetooth function that can be used.
Specific pairing procedures were not the same with different mobile phone. Please refer to
your mobile phone manual for further information. Steps as follows:
a) Please keep the headset and mobile phone in the range of 1 meter when pairing.
b) Start the Bluetooth function of mobile phone and search the Bluetooth devices.
c) Make the headset enter into pairing mode (Please refer to “how to enter into pairing
mode”).
After searched, select “BH-03”in the Bluetooth device list.
a) According to indication, enter password or PIN No:”0000”, and press the key of” Yes”
or “confirmed”.



4

b) After successful pairing, select “BH-03” in the Bluetooth device list, and press
“connect”.
c) After successful connecting, the blue LED of the headset quickly blinks twice or three
times every 4 seconds.
Wearing the headset
The string of this headset is retractable, please adjust according to the actual use. Logo “L” of
headset represents left ear, Logo “R” of headset represents right ear. Please wear the headset
according to the indication of the Logo.

Making calls with the headset
Function Status of headset Operation
Voice dial Standby mode Press and hold MFB for 2s, release it till hearing
indication sound
Redial last
number Standby mode Short press MFB twice quickly
Volume up Conversation
mode Short press or long press + key. When the volume is adjusted to max, you will hear an indication tone.
Volume
down Conversation mode Short press or long press – key. When the volume is adjusted to min, you will hear an indication tone.
Answer
calling Ringing Short press MFB
Reject calling Ringing Press and hold MFB for 1s, and release it till hearing
indication sound
Warning: Excessive pressure from headphones can cause hearing loss.



5

Notes:
•For some mobile phones, when you press the key of accepting on the phone, the
conversation will be sent to the mobile phone. At this time, you can switch the call to
headset by using the conversation switch button or through operating on the mobile
phone. Please refer to the instruction of your mobile phone for further information
Playing music
When the headset connects with the mobile phone or Bluetooth transmitter which supports
A2DP, you can enjoy music through headset wirelessly.
Function Status of headset Operation
Pause Playing music Short press MFB
Play Pausing Short press MFB
Last song Playing music Short press < key
Next song Playing music Short press> key
Volume up Playing music Short or long press + key. When the volume is
adjusted to max, you will hear an indication tone.
Volume down Playing music Short or long press – key. When the volume is
adjusted to min, you will hear an indication tone.
Notes: .
•Remote control the function of last song/next song/pause, it needs your mobile phone
or Bluetooth transmitter supports AVRCP. Please refer to the instruction of your
mobile phone or Bluetooth transmitter. for further information.



6

LED indicator
A) Charging
LED indicator Status of the headset
Red LED is on Charging
Blue LED is on Finish charging
B) In use.
LED Indicator Status of the headset
Red and blue LEDs blink alternately Pairing mode
Blue LED quickly blinks once every 2 seconds. Not connected to a device
Blue LED gradually turns on and off Conversation mode
Red LED blinks twice every 20 seconds Low power
C）Bettery Indicator
Press Bettery Check, Led will on about 3 second.
Four Leds was On. It mean bettery is full, it can be use about 8~10 hours
Three Leds was On. It mean bettery is approaching 75%, it can be use about 5~7 hours
Two Leds was On. It means bettery is approaching 50%, it can be use about 3~5 hours
One Led was On. It means bettery is running out, please charge it.
Re-connecting to a Bluetooth device
A) Automatic connecting
Every time the headset is switched on, it will connect to the nearest, and the last
connected device automatically.



7

B) Manual connecting to last connected device
When the headset is in standby mode and doesn’t connect to any devices, short press
MFB button once, it will connect to last connected device automatically.
15.19Labellingrequirements.

Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwo
conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptany
interferencereceived,includinginterferencethatmaycauseundesiredoperation.


15.21Informationtouser.

Theusersmanualorinstructionmanualforanintentionalorunintentionalradiatorshallcautionthe
userthatchangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliance
couldvoidtheuser'sauthoritytooperatetheequipment.

15.105Informationtotheuser.
(b)ForaClassBdigitaldeviceorperipheral,theinstructionsfurnishedtheusershallincludethe
followingorsimilarstatement,placedinaprominentlocationinthetextofthemanual:

Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,
pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
againstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcan
radiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,may
causeharmfulinterferencetoradiocommunications.However,thereisnoguaranteethat
interferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmful
interferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoff
andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowing
measures:

—Reorientorrelocatethereceivingantenna.

—Increasetheseparationbetweentheequipmentandreceiver.

—Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris
connected.

—Consultthedealeroranexperiencedradio/TVtechnicianforhelp.



8

WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
