Mytee Spyder HP60 User manual

1
Instructions for
HP60 Spyder™
13655 Stowe Dr., Poway, CA 92064
Model #
Serial #
Form # ADP-HP60
9-16
Please read before use.
Register your product
at http://www.mytee.
com/support/register
General Information p. 2
Features p. 5
Operation p. 6
Parts & Pricing p. 8
Wiring Diagram p. 10

2
Dear Customer:
Congratulations on the purchase of your new HP60 Spyder™. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
Keep in mind that the HP60 Spyder™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the HP60 will give quality performance for many years to come.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is properly installed in accordance with all
local code and ordinances. Do not remove ground pin; if missing, replace plug before
use.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualied electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not t the outlet, have a proper outlet installed by a qualied
electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le a
freight damage claim.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or death.
Is used to call attention to a situation that could cause severe personal injury.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of re, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where ammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when cleaning on stairs.
16. To reduce the risk of re or electric shock, do not use this machine with a solid-
state speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alka-
lines, or other dangerous liquids.
19. Do not leave operating unattended.
Filling the Solution Tank
1. Fill the solution tank with the approved cleaning solution.
2. Do not ll up the solution tank completely: 1” should be left free at the top.
3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.
4. Always follow the dilution instructions on the chemical container label.
5. The temperature of the cleaning solution must not exceed 70oC/160oF.
Use only non-ammable liquid in this machine.
Figure 1
Grounding Pin
Grounded Outlet
Grounded Outlet Box
Adapter
Tab for Grounding
Screw
Metal
Screw
Figure 2 Figure 3
GENERAL INFORMATION

3
Setup
1. Open lid of solution tank. Fill solution with water or approved cleaning agent. For
best results, ll with warm water (140°).
Flammable materials can cause an explosion or re. Do not use ammable solutions
or materials in tank(s).
FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.
ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
2. Attach solution hose (located front of machine). NOTE: Make sure the quick
disconnect snap together rmly. As you do this, always inspect hoses for cracks or
fraying. Do not use if hoses are damaged.
3. Attach other end of solution hose to wand.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate
machine unless cord is properly grounded. FOR SAFETY: Do not operate machine
with the use of an extension cord.
6. Turn on pump. Key tool until you have a steady ow.
7. Release tool trigger. Turn on heater.
8. Wait 8–10 minutes for unit to pre-heat.
9. Re-key upholstery tool until hot water begins owing.
10. Once hot water is owing, release trigger and pre-heat an additional 4–5 minutes.
11. Turn on vacuum motor.
12. Begin cleaning. Make two dry passes to every wet pass.
13. For oor cleaning, unplug tool and attach oor wand.
14. Work away from cords to avoid damage.
15. Use a defoamer in your recovery tank.
16. To clean heavily soiled areas, repeat cleaning from different directions.
17. When oat shuts off vacuum, empty tanks.
18. When work is complete, unplug cords and hoses.
19. Wrap and clean hoses. Clean all tanks.
Pre-Operation
1. Vacuum carpet and upholstery and remove other debris.
2. Perform machine setup procedures.
3. Inspect power cord for damage.
Operation
1. Turn the pump switch on.
2. Squeeze the trigger on the tool to release air in the line. Hold until a steady ow of
water comes out of the tool.
3. Once the pump is primed and there is pressure in the solution line, turn on the
heater switch and wait a few minutes for water to heat up.
4. Once water is heated, turn on vacuum and begin cleaning.
Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.
1. Work away from outlet and power cord to prevent cord damage.
2. Use a recommended foam control solution in the recovery tank to prevent vacuum
motor damage. Periodically check for excessive foam buildup in solution tank, and
recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from different direction.
4. When ball oat shuts off vacuum, it is time to empty the dirty water from the
recovery tank, and rell solution tank.
5. After cleaning, relieve water pressure from tool before disconnecting hose.
Squeeze trigger for ve seconds after turning main power switch off.
After Use
1. Unplug.
2. Empty solution tank and rinse it with clean water.
3. Inspect hoses and replace if damaged.
4. Inspect solution lter. Clean or replace if damaged.
5. Store the machine in a clean, dry place.
6. Open recovery tank cover to promote air circulation.
Maintenance Schedule
Maintenance item Daily Once a week
Clean and inspect tanks
Clean and inspect hoses
Check lters
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee System Maintainer
Remove and clean oat shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs
x
x
x
x
x
x
x
x
x
Troubleshooting
There is no power.
• Plug the machine into proper outlets.
• Check the circuit breaker. Other devices should not run on the same circuit as the
extractor. Use a 20 amp outlet.
Pump does not work properly.
• Make sure solution line quick disconnects are properly connected.
• Check Solution tank. May be empty.
• Jets may be clogged. Remove jet and ush clean.
• Filters clogged. Remove lters, clean and ush with water.
• Heater may be partially blocked. Flush system with System Maintainer.
• Inspect the heater check valve. Replace if necessary.
• Check pump wire(s). Reconnect or replace when necessary.
• Check panel actuation switch. Replace if faulty.
• Worn pump motor brushes (if equipped). Replace pump motor.
• Refer to relevant in-depth troubleshooting information in “Technical Support” section
of Mytee website for specic pump type. http://www.mytee.com/support/.
Heater does not function.
• Check manual sensor on heater (reset by pressing button on sensor). Replace if
non-functional.
• Check automatic sensor. Check for continuity when cool. Replace if found faulty.
• Heating element may have failed. Replace. Check using ammeter when heater is
engaged independently.
• Reconnect heater wire, if disconnected.
• Refer to relevant in-depth troubleshooting information in “Technical Support” section
of Mytee website. http://www.mytee.com/support/.
Vacuum motor does not function properly.
• Check that all vacuum hoses are tightly connected.
• Close recovery tank drain valve completely.
• Hose/tool blockage or leakage. Repair or unblock the tool or hose.
• Secure the vacuum tank lid tightly.
• Grinding noise from blower indicates impeller failure from debris, dry vacuuming,
and over lling/foaming. Replace vacuum motor.
• Worn motor brushes. Replace vacuum motor.
THE FOLLOWING APPLIES TO BRAND NEW MACHINES:
Pump system will not ow water.
• The system could be vapor locked, which results from activating the heater before
the pump. Release pent-up pressure by removing extractor outlet disconnect, or by
depressing the disconnect inner poppet valve using a dull plastic object (such as a
pen). Resume operation, using proper technique outlined beginning on page 6.
• Check outlet disconnect. Remove to test. Replace if necessary.
• Hanging heater check valve. Remove hose to heater check valve, and manually
manipulate the internal valve poppet ball with straightened paper clip. Replace hose
to test. Replace faulty check valve (B108).
Unit is tripping circuit breaker(s).
• Ensure that only a 20 amp circuit is being used.
• Use only a cord approved for the machine.
• Do not add any extension cords to those cords supplied for use with extractor.
• Faulty component may be drawing excessive amperage. Check each component
separately.
Faulty circuit breaker at site. Use another outlet.
Accessories (optional)
2200 Airmover
3601 System Maintainer
2700 Mytee-Dry
8700 Crevice Tool
GENERAL INFORMATION

4
Machine Specications
Solution Tank 5 gallons (approx.)
Recovery Tank 5 gallons
Vacuum Single 3-stage low amp
CFM 100
Water Lift 130”
Pump PSI 120
Pump GPM 1.3
Heater 1,200W - 210° max.
Power
Consumption 20 amps @ 115V 60Hz
Machine Weight 69 lbs.
Machine
Dimensions 25” x 15.5” x 29.5”
Power Cord 25’ 12/3
230V Conguration Information
Model Number HP60-230
Power
Consumption 10 amps @ 230V 60Hz/50Hz
FAQs
Q: What comes standard with the HP60?
A: The HP60 comes with a hose hanger ( H375 ), a 25’ 12/3 Cord, 15’ 1-1/4”
Vacuum/Solution Hose ( 8501 ), Cuff-Lynx™ 1-1/4” reducer ( H122 ) and a
3” Stainless Steel Upholstery Tool ( 8400 ).
Q: Does Mytee recommend a tool for the machine?
A: A variety of tools can be used with the unit, including our 8390 wand, 8700 crevice
tool, and 8400 upholstery tool.
Q: Where do I plug the machine in?
A: The HP60 requires a 20A grounded circuit. Please note: GFI outlets may trip
before the breaker setting.
Q: Are the pumps re-buildable for the HP60?
A: Yes, both the seals and the pistons have repair kits available.
Please see the pump manual that shipped with your machine for the
maintenance schedule.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run a System Maintainer through
the system to keep the hoses, pump, and heater clean and free of debris.
GENERAL INFORMATION

5
BACK
ACCESSORIES
FRONT
1. Waist high controls
2. 2” Male Cuff-Lynx™
3. Female quick disconnect
4. Solution tank
5. Solution tank lid
6. Easy open lid
7. Motor base housing
8. Locking casters
9. Vent guard
10. Single 25’ power cord
11. Bucket-high drain valve
4
3
1
2
7
8
HP60 SPYDER™ FEATURES
5
6
9
11
10
H141 Cuff-Lynx™
1.5” Reducer
8501 15’ x 1.25”
Hose-n-Hose™
Vac / Sol Hose Combo
H375 Hose Hanger
& 2 Screws
8400 4” Stainless Steel
Upholstery Tool
H122 Cuff-Lynx™
1.25” Reducer

6
PUMP
After the machine has been plugged into a 20 amp grounded out-
let, turn on pump. Squeeze the trigger on the tool until it releases
a steady ow.
ATTACH HOSES
Attach one end of a solution hose to a wand or other tool, the
other end to the Spyder’s™ front quick disconnect. Attach one
end of a vacuum hose to the tool, the other end to the Spyder’s™
Cuff-Lynx™ vacuum hose port.
HEATER
Release tool trigger. Turn on heater. Wait 8 – 10 minutes for unit
to pre-heat. Once heated, re-key upholstery tool until hot water
begins owing. Once hot water is owing, release trigger and
pre-heat an additional 4 – 5 minutes.
VACUUM PUMP HEATER
HP60 SPYDER™ OPERATION
VACUUM PUMP HEATER
FILL SOLUTION TANK
Lift lid to ll. For best results, ll with warm water (140° F).

7
RECOVERY TANK
Add a defoamer in the recovery tank to reduce foam, prolonging
the life of the Spyder™ vacuum motor .
ENGLISH
45 DEGREE SPOUT DRAIN
When the oat shuts off vacuum, empty tank. Pull lever located at
the back of the machine to release water.
MYTEE® SYSTEM MAINTAINER
Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
HP60 SPYDER™ OPERATION
VACUUM MOTOR
Turn on vacuum motor and begin cleaning. For best results
make two dry passes to every wet pass.
VACUUM PUMP HEATER

8
HP60 SPYDER™ PARTS & PRICING
Part prices are subject to change.
ITEMS NOT SHOWN:
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
H273
nut, kep, #10-32 zinc
6
$0.99 ea
2
H256
screw, 10-32 x 3/4" phil pan head, zinc
2
$0.99 ea
3
H528
bracket, heater mounting, dual
1
$29.99 ea
4
E571
heating rod, 600W, 115V
2
$49.99 ea
5
H274
screw, 6 x 3/16, phil pan head, self-tapping
10
$0.99 ea
6
E574
Thermostat, 310°F ± 10°F, Manual, 1/4"
2
$17.99 ea
7
E573
Thermostat, 200°, Auto, 1/4"
2
$16.49 ea
8
H903A
heater, aluminum cast, single
2
$78.99 ea
9
B103
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
6
$4.49 ea
10
AH108S
sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi
1
$26.49 ea
11
AH156
hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray
1
$23.99 ea
12
B207
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt 1
$5.99 ea
13
B108
valve, brass, 1/4" check
1
$13.99 ea
14
AH184
hose, 3/8" x 14-1/2" (OAL), f surge
1
$27.99 ea
15
B652
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
1
$8.49 ea
16
C305
pump, 120 psi, 115V
1
$151.99 ea
17
H210
washer, 1/4" flat, s/s
24
$0.99 ea
18
H186
screw, 10-32 x 3/4, phil flat full thread
4
$0.99 ea
19
B172
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
1
$9.49 ea
20
B173
ferrule, 1/2", brass
2
$0.99 ea
21
PH615-20
sol hose, 1/2" kuri 100psi
1
$8.99/ft
22
B160
adapter, brass, 1/2" barb x 3/8" fsw, ball end
1
$3.49 ea
23
E531
power cord, end, 25', 12/3 black
1
$52.99 ea
24
H220
fitting, strain relief, cord
1
$3.19 ea
25
H221
nut, lock, 1/2" steel
1
$1.99 ea
26
P791
base, spyder
1
$106.99 ea
27
H304
screw, 8 x 5/8", phil oval, s/s
15
$0.99 ea
28
H296
guard, cooling fan, wire
2
$2.99 ea
29
H135
Cuff-Lynx, 2" m cuff x 2" mpt
1
$3.99 ea
30
H216
nut, lock, 1/4-20, nylon insert, s/s
18
$0.99 ea
31
H342
bolt, 1/4-20 x 1" hex head, s/s 16
$0.99 ea
32
H667
caster, 3", Black Hub, Gray Tread
4
$14.99 ea
33
P792
sol tank, spyder
1
$103.99 ea
34
H215
nut, hex, 1/4-20 s/s
1
$0.99 ea
35
H213
washer, 1/4" lock, s/s
3
$0.99 ea
36
H211 washer, 1/4"id x 1"od, flat, s/s
2
$0.99 ea
37
G052
washer, buna 1-1/8" od x 3/16" id
2
$1.99 ea
38
H203
bolt, 1/4-20 x 1-1/4" hex head, s/s
1
$0.99 ea
39
P965
cover, sol tank, spyder
1
$12.00 ea
40
H316
bolt, 1/4-20 x 1-1/2" hex head, s/s
2
$0.99 ea
41
H379
bracket, front, small
1
$3.99 ea
42
H201
bolt, 1/4-20 x 1/2" hex head, zinc
2
$0.99 ea
43
B119
filter, strainer, 1/4"
1
$3.99 ea
44
H212
flat washer, 9/16"ID x 1 1/16"OD, AN960-C916
6
$0.99 ea
45
B107 nipple, brass, 1/4"m, hex
3
$3.19 ea
46
B105
bushing, brass, 3/8"mpt x 1/4"
1
$3.19 ea
47
B102
qd, brass, 1/4" f x 1/4" fpt
1
$17.99 ea
48
B111
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
1
$3.49 ea
49
AH157
hose, 3/8" x 9" (OAL), f x f, surge, 1600psi
1
$25.99 ea
50
H770
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
8
$0.99 ea
51
H307
washer, star, 1/4" steel zinc
2
$0.99 ea
52
H912
bracket, rear, fb/spy
1
$9.99 ea
53
P793
vac tank, spyder
1
$117.99 ea
54
H314
nut, lock, 1-1/2", steel
1
$1.99 ea
55
P520
adapter, pvc, 1-1/2" mpt x 1-1/2" fms
1
$2.99 ea
56
PH633-6
PIPE, PVC, 1-1/2" x 7-1/2" LG.
1
$4.99/ft
57
H297
screw, 8 x 1/2", hex head, zinc
3
$0.99 ea
58
P755
elbow, U, 180, 1-1/2", float
1
$8.99 ea
59
H490
float, 2"/ 1.5" ball style 1
$19.99 ea
60
G090 lid, vac tank, clear, 7"
1
$36.99 ea
61
G091
gasket, 7", vac lid
1
$11.99 ea
62
A926
elbow, inlet assembly 2"
1
$15.99 ea
63
H225
valve, drain, 1-1/2" 1
$20.99 ea
64
H226
spout, drain, 45 degree
1
$3.19 ea
65
H390A
bracket, "L"
2
$6.99 ea
66
G059
exhaust boot, plastisol
1
$4.99 ea
67
H217
clamp, hose, 2-1/4 dia
1
$1.49 ea
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
68
C302LA
vac motor, 3 stage, low amp
1
$139.99 ea
69
H096
bolt, hex, 1/4-20 x 4", zinc Finish
3
$0.99 ea
70
H503
vac support, 3 stage, 3.25", no thrds
3
$3.99 ea
71
G004
gasket, vacuum motor
1
$8.99 ea
72
H636
plate, 3 switch
1
$6.99 ea
73
H246
screw, 8-32 x 3/8" SHCS, alloy, Black
4
$0.99 ea
74
E515
switch, rocker, 2 position
3
$13.99 ea
PART NO.
DESCRIPTION
QTY.
MSRP
ADM-HP60
manual, spyder
1
A998
harness, electrical
1
$73.99 ea
G008
piglet filter
1
$6.29 pak
H375
hanger, wire formed, hose
1
$10.99 ea
G079 hose wrap, heat guard
1
$2.99 ea
H230
screw, 10-32 x 1/2" phil pan head, s/s 2
$0.99 ea
A935
sol hose, pigtail, 1/8 x 7 1/2
1
$14.99 ea
B101
quick disconnect, male, 1/4" male x 1/4" fpt
2
$8.49 ea
H282
tool, uph, s/s w/valve
1
$98.99 ea
H701
hose, vac, 15' x 1-1/4" w/ 1 1/2 black cuffs
1
$44.99 ea
AH136
sol hose, 1/5" x 15', 1/8 mpt x 1/4 mpt
1
$44.99 ea
B102
quick disconnect, 1/4" female x 1/4" fpt
1
$17.99 ea
B104
bushing, hex, 1/4" mpt x 1/8" fpt
1
$1.99 ea
H133
Cuff-Lynx, 1-1/4" hose x male & female
2
$9.99 ea
H122
Cuff-Lynx, 1.25" hose cuff x 2" female cuff
1
$3.99 ea
P590
cuties, 1/4" qd, standard pack of 2
1
$2.99 ea
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
HP60
SHEET 1 OF 3
SCALE: 1:3
REV
DWG. NO.
D
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
mytee
PRODUCTS, INC.
858-679-1191
M.LaBarbera
1/2014
F
DO NOT SCALE DRAWING
Spyder

9
HP60 SPYDER™ PARTS & PRICING
1
2
3
4
6
79
8
10
9
9
11
12
13
14
15
19
21
22
23
24
25
26
27
28
32
40
17
41
17
42
35
47
48
44
45
44 9
49
45
44
44
9
33 34
35 36
37
37
38 38
50
52
55
56
58
59
27 60
61
29
62
63 64
65
50
53
To female q.d.
thru B103
#
9
To sol tank
thru B105
#
46
To pump "IN"
thru B160
#
22
To heater "OUT"
thru AH108S
#
10
18
19
1
16
46
43
45
30
9
44
44
5
39
57
72
73
74
31
50
51
68
69
70
71
54
17
30
20
20
67 66
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
HP60
SHEET 2 OF 3
Spyder
SCALE: 1:5
REV
DWG. NO.
D
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
mytee
PRODUCTS, INC.
858-679-1191
M.LaBarbera
1/2014
F
DO NOT SCALE DRAWING

10
HP60 SPYDER™ WIRING DIAGRAM
HP-60
115 Volt System
L1 L2
G
Primary Cord
VAC
L2L1
G
C-302LA
Pump
L2L1
G
C-313A
600 Watt Heat
600 Watt Heat
G G
E-515
E-515
E-516
To Metal
Plate
1/15/2014

11
Mytee Products Inc.
13655 Stowe Dr.
Poway, CA 92064
www.mytee.com
© 2016 Mytee Products Inc.
Printed in the U.S.A.
NOTES