Mytee Contractor's Special 2002CS User manual

1
Instructions for
2002CS Contractor’s Special™
13655 Stowe Dr., Poway, CA 92064
Model #
Serial #
Form # ADM-2002CS
11-16
Please read before use.
Register your product
at www.mytee.com/
support/register
General Information p. 2
Features p. 5
Operation p. 6
Parts & Pricing p. 8
Wiring Diagram p. 10
Notes p. 11

2
Dear Customer:
Congratulations on the purchase of your new Contractor’s Special™. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
Keep in mind that the Contractor’s Special™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the Contractor’s Special™ will give quality performance for many
years to come.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com.
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed in accordance
with all local code and ordinances. Do not remove ground pin; if missing, replace
plug before use.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualied electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not t the outlet, have a proper outlet installed by a qualied
electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le a
freight damage claim.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or death.
Is used to call attention to a situation that could cause severe personal injury.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of re, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where ammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when cleaning on stairs.
16. To reduce the risk of re or electric shock, do not use this machine with a solid-
state speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alka-
lines, or other dangerous liquids.
19. Do not leave operating unattended.
Filling the Solution Tank
1. Fill the solution tank with the approved cleaning solution.
2. Do not ll up the solution tank completely: 1” should be left free at the top.
3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.
4. Always follow the dilution instructions on the chemical container label.
5. The temperature of the cleaning solution must not exceed 70oC/160oF.
Use only non-ammable liquid in this machine.
Figure 1
Grounding Pin
Grounded Outlet
Grounded Outlet Box
Adapter
Tab for Grounding
Screw
Metal
Screw
Figure 2 Figure 3
GENERAL INFORMATION

3
Setup
1. Open lid of solution tank. Fill solution with water or approved cleaning agent. For
best results, ll with warm water (140o).
Flammable materials can cause an explosion or re. Do not use ammable solutions
or materials in tank(s).
FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.
ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
2. Attach solution hose (located front of machine). NOTE: Make sure the quick
disconnect snap together rmly. As you do this, always inspect hoses for cracks or
fraying. Do not use if hoses are damaged.
3. Attach other end of solution hose to wand.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate
machine unless cord is properly grounded. FOR SAFETY: Do not operate machine
with the use of an extension cord.
6. Turn on pump. Key tool until you have a steady ow.
7. Release tool trigger. Turn on heater.
8. Wait 8–10 minutes for unit to pre-heat.
9. Re-key upholstery tool until hot water begins owing.
10. Once hot water is owing, release trigger and pre-heat an additional 4–5 minutes.
11. Turn on vacuum motor.
12. Begin cleaning. Make two dry passes to every wet pass.
13. For oor cleaning, unplug tool and attach oor wand.
14. Work away from cords to avoid damage.
15. Use a defoamer in your recovery tank.
16. To clean heavily soiled areas, repeat cleaning from different directions.
17. When oat shuts off vacuum, empty tanks.
18. When work is complete, unplug cords and hoses.
19. Wrap and clean hoses. Clean all tanks.
Pre-Operation
1. Vacuum carpet and upholstery and remove other debris.
2. Perform machine setup procedures.
3. Inspect power cord for damage.
Operation
1. Turn pump switch on.
2. Pull up on tool lever to release air in the line. Hold lever until a steady ow of water
comes out of the wand.
3. Once pump is primed and there is pressure in the solution line, turn on heater switch
(if model is equipped with heater) and wait a few minutes for water to heat up.
4. Once water is heated, turn on vacuum and begin cleaning.
Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.
1. Work away from outlet and power cord to prevent cord damage.
2. Use a recommended foam control solution in the recovery tank to prevent vacuum
motor damage. Periodically check for excessive foam buildup in solution tank, and
recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from different direction.
4. When ball oat shuts off vacuum, it is time to empty the dirty water from the
recovery tank, and rell solution tank.
5. After cleaning, relieve water pressure from tool before disconnecting hose.
Squeeze trigger for ve seconds after turning main power switch off.
After Use
1. Unplug.
2. Empty solution tank and rinse it with clean water.
3. Inspect hoses and replace if damaged.
4. Inspect solution lter. Clean or replace if damaged.
5. Store the machine in a clean, dry place.
6. Open recovery tank cover to promote air circulation.
Maintenance Schedule
Maintenance item Daily Once a week
Clean and inspect Tanks
Clean and inspect Hoses
Check lters
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee system maintainer
Remove and clean oat shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs
x
x
x
x
x
x
x
x
x
Troubleshooting
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker; reset circuit breaker, other items should not run on the
same circuit as machine. Outlet must be a 20-amp circuit.
Pump does not work properly.
1. Snap quick disconnects rmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and ush clean.
4. Filters clogged, remove lters and rinse clean with water.
5. Heater is blocked; ush out with Mytee’s system maintainer.
6. If brass check valve is stuck replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate switch may need to be replaced.
9. If pump motor brushes are worn, replace pump.
Heater does not work properly.
1. If sensor mounted on the heater has popped, reset sensor by pushing in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly.
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
4. If ball oat is shut off, empty vacuum tank of all wastewater.
5. Make sure ball oat is rmly installed on the elbow.
6. If water is coming out of vacuum motor, use a low foaming detergent.
7. Clean upholstery tool or oor wand jets.
Accessories (optional)
3601 System Maintainer
8400DX Mytee Dry™ upholstery tool
8390 Wand
8700 Crevice Tool
Machine Specications
Solution Tank 10 gallons
Recovery Tank 9 gallons
Vacuum Single 3-stage low amp
CFM 100
Water Lift 130”
Pump PSI 120
Pump GPM 1.3
Heater 1,200W - 210° max.
Power
Consumption 20 amps @ 115V 60Hz
Machine Weight 120 lbs.
Machine
Dimensions 28” x 18.5” x 39”
Power Cord 25’ 12/3
230V Conguration Information
Model Number 2002CS-230
Power
Consumption 10 amps @ 230V 60Hz/50Hz
GENERAL INFORMATION

4
GENERAL INFORMATION
FAQs
Q: What comes standard with the Contractor’s Special™?
A: The Contractor’s Special™ comes with 15’ 1-1/2” Vacuum/Solution Hose and a
12” wand and Cuff-Lynx™ reducer.
Q: Where do I plug the machine in?
A: The Contractor’s Special™ requires a 20A grounded circuit. Please note: GFI
outlets may trip before the breaker setting.
Q: Are the pumps re-buildable for the Contractor’s Special™?
A: Yes, both the seals and the pistons have repair kits available.
Please see the pump manual that shipped with your machine for the
maintenance schedule.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run a System Maintainer through
the system to keep the hoses, pump, and heater clean and free of debris.

5
CONTRACTOR’S SPECIAL™ 2002CS FEATURES
2002CS FRONT 2002CS BACK
2002CS ACCESSORIES
1. Waist high controls
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female QD
5. Solution tank
6. Front vent
7. Clear recovery tank lid
8. Push handle
9. Recovery tank
10. Recovery tank drain valve
11. Vacuum exhaust
12. Rear vent
13. 25’ lighted power cord
14. 12” rear wheels
15. 5” locking casters
8300-EZ-C - 12” Wand
5
2
615
H226 - Drain Elbow
8501-15’ 1-1/2” Vac/Sol Hose
H141 - 1 1/2” Cuff-Lynx™
1
4
3
8
7
14
11
REPLACING HOSE CUFFS WITH CUFF-LYNX™
Once you receive your Contractor’s Special™, you will need to
replace the cuffs on your vacuum hose. To remove old cuffs, twist
clock-wise. To attach reducer Cuff-Lynx™ to vacuum hose twist
counter clock-wise.
Twist clock-wise to remove standard cuffs.
Twist counter clock-wise to attach Cuff-Lynx™ to vac. hose.
9
13
12
10

6
CONTRACTOR’S SPECIAL™ 2002CS OPERATION
2002CS ATTACH HOSES
Firmly attach the hose and quick disconnect. Make sure the quick
disconnects snap together rmly. Once attached to the unit,
connect the quick disconnect to the upholstery tool. Always
inspect hoses for cracks or fraying.
2002CS VACUUM, PUMP & HEATER
To start the Contractor’s Special™, switch on the pump rst.
Pull the trigger on your cleaning tool until water sprays out, then
switch on the heater. Allow the heating element to heat up, then
switch on the vacuum and begin cleaning.
2002CS FILL SOLUTION TANK
Lift the lid to ll. For best results, ll with warm water (140° F).
ATTACH VAC & SOLUTION HOSE TO WAND
Attach the hose cuff to the end of the wand tube. Attach the
female quick disconnect to the male quick disconnect located near
the wand trigger.

7
CONTRACTOR’S SPECIAL™ 2002CS OPERATION
2002CS SYSTEM MAINTAINER2002CS ADDING DEFOAMER
Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance, and pressure.
Add a defoamer in the recovery tank to reduce foam, prolonging
the life of the Contractor’s Special™ vacuum motor.
2002CS RECOVERY TANK DRAIN
When the oat shuts off vacuum, empty tank. Pull lever located at
the back of the machine to release water.
2002CS LOCKING CASTERS
Locking casters help keep the machine remain stationary during
use.

8
CONTRACTOR’S SPECIAL™ 2002CS PARTS & PRICING
Part prices are subject to change.
ITEMS NOT SHOWN
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
H296
guard, cooling fan, wire
2
$2.99 ea
2
H304
screw, #8 x 5/8 phil oval, s/s
14
$0.99 ea
3
H216
nut, lock, 1/4-20, nylon insert, s/s
10
$0.99 ea
4
H210
washer, 1/4" flat, s/s
19
$0.99 ea
5
H342
bolt, 1/4-20 x 1" hex head, s/s 8
$0.99 ea
6
H666
caster, 5", Black hub & gray tread
2
$23.19 ea
7
H254
washer, axle, cut 1/2" id
4
$0.99 ea
8
H251
wheel, 12"
2
$41.99 ea
9
H042
c-clip, 12mm, external
2
$0.99 ea
10
H371
axle, 18.03" x .50" dia
1
$9.99 ea
11
AH184
sol hose, pulse, 3/8" x 14.5" fsw x 1/4 fsw x 1/4 fpt
1
$27.99 ea
12
AH156
hose, 3/8", (OAL), f x fs, 5400 gray
1
$23.99 ea
13
B103
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
2
$4.49 ea
14
H273
nut, kep, #10-32 zinc
6
$0.99 ea
15
H528
bracket, heater mounting, dual
1
$29.99 ea
16
H256
screw, 10-32 x 3/4" phil pan head, zinc
6
$0.99 ea
17
E571
heating rod, 600W, 115V
2
$49.99 ea
18
B142A
coupling, brass, 1/4" fpt x 1/4" fpt
1
$4.49 ea
19
B108
valve, brass, 1/4" check
1
$13.99 ea
20
H274
screw, 6 x 3/16, phil pan head, self-tapping
10
$0.99 ea
21
H903A
heater, aluminum cast, single
2
$78.99 ea
22
E573
Thermostat, 200°, Auto, 1/4"
2
$16.49 ea
23
E574
Thermostat, 310°F ± 10°F, Manual, 1/4"
2
$17.99 ea
24
AH120
sol hose, 28" x 1/4", 1/4 fpt
2
$35.49 ea
25
H221
nut, lock, 1/2" steel
1
$1.99 ea
26
H220
fitting, strain relief, cord
1
$3.19 ea
27
E531
power cord, end, 25', 12/3 black
1
$52.99 ea
28
P731
base
1 $141.99 ea
29
PH615-34
sol hose, 1/2" kuri 100psi
1
$8.99/ft
30
B160
adapter, brass, 1/2" barb x 3/8" fsw, ball end
1
$3.49 ea
31
B186
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
1
$8.99 ea
32
B652
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
1
$8.49 ea
33
H299
washer, 11/16"id x 1-1/2"od x .075, s/s
4
$0.99 ea
34
H222
screw, 10-32 x 1-1/4" phil pan head, s/s 4
$0.99 ea
35
C305
pump, 120 psi, 115V 1 $151.99 ea
36
B172
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
1
$9.49 ea
37
B173
ferrule, 1/2", brass
2
$0.99 ea
38
H912
bracket, rear, fb/spy
1
$9.99 ea
39
H770
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
8
$0.99 ea
40
H307
washer, star, 1/4" steel zinc
2
$0.99 ea
41
H217
clamp, hose, 2-1/4 dia
2
$1.49 ea
42
PH628-24
vac hose, 2", wire reinforced
1
$8.99/ft
43
H124
Cuff-Lynx, 2" mpt x 2" female cuff
2
$3.99 ea
44
H194
coupler, 2" dia x 2.5" length, s/s
1
$10.00 ea
45
H203
bolt, 1/4-20 x 1-1/4"
2
$0.99 ea
46
H211
washer, 1/4"id x 1"od, flat, s/s
4
$0.99 ea
47
G052
washer, buna 1-1/8" od x 3/16" id
4
$1.99 ea
48
H213
washer, 1/4" lock, s/s
7
$0.99 ea
49
H215
nut, hex, 1/4-20 s/s
2
$0.99 ea
50
G018
cover, sol tank (sp)
1
$12.99 ea
51
P732
sol tank
1 $141.99 ea
52
B107
nipple, brass, 1/4"m, hex
2
$3.19 ea
53
H484
plate, mounting, QD
1
$4.99 ea
54
B111
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
1
$3.49 ea
55
B102
qd, brass, 1/4" f x 1/4" fpt
1
$17.99 ea
56
H201
bolt, 1/4-20 x 1/2", hex head, zinc
2
$0.99 ea
57
H378
bracket, front hinge, sp/fb
1
$8.99 ea
58
H316
bolt, 1/4x1-1/2", hex head zinc
2
$0.99 ea
59
B119A
filter, strainer, 1/2"
1
$6.49 ea
60
B210
bushing, brass, 1/2"mpt x 3/8" fpt, hex
1
$2.49 ea
61
B216
nipple, brass, 3/8" x close
1
$1.99 ea
62
H226
spout, drain, 45 degree
1
$3.19 ea
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
63
H225
valve, drain, 1-1/2"
1
$20.99 ea
64
P733
vac tank
1 $190.99 ea
65
A926
elbow, inlet assembly 2"
1
$15.99 ea
66
PH633-3
pipe, pvc, 1-1/2"
1
$4.99/ft
67
P503
adapter, 1.5" pvc, 45 deg, fslip x fslip
2
$3.29 ea
68
PH633-4
pipe, pvc, 1-1/2"
1
$4.99/ft
69
PH633-06
pipe, pvc, 1-1/2"
1
$4.99 ft
70
H343
screw, 10 x 5/8" hex head, zinc
3
$0.99 ea
71
P755
elbow, U, 180, 1-1/2", float
1
$8.99 ea
72
G091
gasket, 7", vac lid
1
$11.99 ea
73
G090 lid, vac tank, clear, 7"
1
$36.99 ea
74
H490
float, 2"/ 1.5" ball style 1
$19.99 ea
75
P520
adapter, pvc, 1-1/2" mpt x 1-1/2" fms
1
$2.99 ea
76
H314
nut, lock, 1-1/2", steel
1
$1.99 ea
77
H135
Cuff-Lynx, 2" m cuff x 2" mpt
1
$3.99 ea
78
E515
switch, rocker, 2 position
3
$13.99 ea
79
H389
screw, 10-32 x 1/2" SHCS, alloy 2
$0.99 ea
80
H612
Washer, #8, flat regular
2
$0.99 ea
81
H338
plate, switch, sp, 3 hole
1
$6.99 ea
82
G004
gasket, vacuum motor
1
$8.99 ea
83
H503
vac support, 3 stage, 3.25", no thrds
3
$3.99 ea
84
H390A
bracket, "L"
2
$6.99 ea
85
H096
bolt, hex, 1/4-20 x 4", zinc Finish
3
$0.99 ea
86
C302LA
vac motor, 3 stage, low amp
1 $139.99 ea
PART NO.
DESCRIPTION
QTY.
MSRP
ADM-CS
manual, grandprix
1
N/A
8300-EZ-C
EZ glider wand, 12", dual jet, 2 piece
1 $199.99 ea
H141
Cuff-Lynx, 2" to 1.5" reducer
1
$3.99 ea
8500 hose assem, vac\sol, 15' x 1.5" 1 $118.99 ea
H375
hose hanger
1
$10.99 ea
H230
screw, 10-32 x 1/2" phil pan head, s/s 2
$0.99 ea
G102
gasket, cork, 3/4" X 3", 1/8“ thick
3
$1.99 ea
A999
harness, electrical, 2002CS
1
$73.99 ea
G008
black piglet filters, pack of 25
1
$9.99 ea
P590
cuties, 1/4" qd, standard pacl of 2
1
$2.99 ea
G079
hose wrap, heat guard
3
$2.99 ea
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
2002CS
SHEET 1 OF 3
firebird
2/2016
OD
SCALE: 1:48
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
M.LaBarbera
Contractor’s
Special

9
CONTRACTOR’S SPECIAL™ 2002CS PARTS & PRICING
1
2
3
4
5
6
7
7
8
9
10
11
12
13
14
15
16
17
20
23
20
22
21
18
19
13
24
25
26
27 28
29 30
31
32
33
33
34 4
35
36
37
14
41
42
44
43
45 46 47
47 46
48
49
50
51
24
52 53 16
54
55
52
4
48
56
57
3
4
58
59
60
33 33
61
38
39
40
39
62
63
64
65
72
73
2
66
75 76
77
78
79
80
81
82
84
39
85
48
4
86 83
67
67
69
68
71
74
70
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
2002CS
SHEET 2 OF 3
firebird
2/2016
OD
SCALE: 1:48
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
M.LaBarbera
Contractor’s
Special

10
CONTRACTOR’S SPECIAL™ 2002CS WIRING DIAGRAM
2002CS
115 Volt System
L1 L2
G
Primary Cord
VAC
L2L1
G
C-302LA
Pump
L2L1
G
C-305
600 Watt Heat
600 Watt Heat
G G
E-515
E-515 E-515
To Metal
Plate
1/16/2014

NOTES