Mytee Speedster LTD3 Firmware update

1
Instructions for
Speedster® LTD3, LTD5 & LTD12
Please read before use.
Model #
Serial #
Form # ADM-SLTD
3-12
LTD3 p.2
LTD5 p.9
LTD12 p.16
General & Maintenance information p.23
13655 Stowe Dr., Poway, Ca. 92064
Register your product
at www.mytee.com/help

2
SPEEDSTER® LTD3 BACKSPEEDSTER® LTD3 FRONT
SPEEDSTER® LTD3 CORD
SPEEDSTER® LTD3 ITEMS INCLUDED
H375-Hose Hanger H226 Drain Elbow
(4) screws
H110 Cuff-Lynx™ H141 Cuff-Lynx™
2” x 2” Hose Adapter 2” x 1.5” Hose Reducer
FILTERS
G008 - Pack of Piglet™
lters
7. Front Fan
8. Side Vents
9. Solution Lid
10. PSI Gauge
11. Recovery Lid
12. Push Handle
1. Switch Plate
2. 2” Male Cuff-Lynx™ Inlet
3. Prime Value
4. Female Quick Disconnect (QD)
5. Front Handle
6. Pressure Regulator
13. Recovery Tank
14. Solution Tank
15. 4” Locking Casters
16. 10” foam lled
semi-pneumatic wheels
17. Hour Meter
18. Power Cords
19. Auto Fill/Pump Out
Hose Connections
20. Solution Tank Drain
21. Service Latches
22. Rear Vacuum Exhaust
Optional Mufer Port
23. Recovery Tank Drain Valve
3
1
10
5
4
2
6
9
12
14
11
13
15
16
18
19
20
21
(Primary) Right Cord: Plug in yellow-tagged power cable
for Power To Vac 1, Pump, & 600W Heater.
(Secondary) Left Cord: Plug in power cable for Vac 2,
Pump-Out & 1,000W Heater.
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates and the audible tone sounds,
the machine is on separate circuits (not necessarily 20A circuits).
You can identify the primary cord by the yellow tag.
Yellow tag
indicates primary
cord.
SPEEDSTER® LTD3
7
8
22
17
23

3
SPEEDSTER® LTD3 PRIME VALVE &
PRESSURE REGULATOR
SPEEDSTER® LTD3 VAC/SOL
HOSE CONNECTIONS
Attach female end of a solution hose to a wand or tool and the
male end to the LTD’s QD. Then connect a vacuum hose to a
wand and the 2” male Cuff-Lynx™ hose port. (If using the optional
de-foamer, install the kit onto the vacuum port according to the
instructions that come with the de-foamer kit.)
SPEEDSTER® LTD3 SWITCHES
To use vacuum, turn on Vac 1 and Vac 2. To use pump, turn on
Pump. To use pump-out, turn on Pump-Out switch. To use Heater,
turn on Heater.
Vac 1 Vac 2 Pump Pump
out
SPEEDSTER® LTD3 FILL SOLUTION TANK
You can lift the lid to manually ll the tank or follow the “Operating
Instructions” for auto-ll use.
Heater
SPEEDSTER® LTD3
Prime the pump by having the Prime Valve parallel with its pipe
and turn it clock-wise to run the pump. Turning the Pressure Regu-
lator to its left will decrease water pressure and turning to the right
will increase water pressure.
*Please refer to the Pressure Gauge to monitor your water pressure.

4
SPEEDSTER® LTD3 AUTO-FILL CONECTIONS
Using one end of a ½” garden hose, attach it to the mounted
connection behind the LTD unit, then attach the other end to the
desired faucet connection. Turn on the faucet water and let the
auto-ll begin to ll. It will shut off when the water level reaches
the LTD’s electronic oat switch.
SPEEDSTER® LTD3 RECOVERY DRAIN VALVE
Make sure the Auto-Fill is turned off and then locate and lift the
bucket high drain valve on the rear of the LTD unit to empty
the tank.
SPEEDSTER® LTD3 PUMP-OUT CONNETIONS
Using a separate ½” garden hose, attach one end to the LTD’s
mounted pump-out connection and lay the other end of the hose
in a drainable location. With the pump-out switch activated and
the valve parallel with its pipe, the unit will automatically drain
water from the ll tank while the auto-ll maintains water levels.
Make sure ball valve is open!
SPEEDSTER® LTD3
The LTD is equipped with an electronic oat switch inside the
recovery and solution tank. The recovery oat switch is activated
by rising water to prevent suction into the vacuum stacks damag-
ing the motors. The solution oat switch shuts off the auto-ll once
water lever reaches switch.
Electronic shut-off
switches prevents
water from getting
into the vacuum stack
& monitors water level
in solution tank.
VAC STACK
SPEEDSTER® LTD3
FLOAT SWITCHES

5
MYTEE® SYSTEM MAINTAINER
Weekly ushing of the solution system with Mytee System Main-
tainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance, and pressure.
SPEEDSTER® LTD3 SOLUTION TANK DRAIN VALVE
To remove any remaining water in the solution tank, located
on the back of the unit is a cap, twist and remove cap to
empty tank.
TIGHTEN
LOOSEN
SPEEDSTER® LTD3
SPEEDSTER® LTD3
FILTER MAINTENANCE
The LTD’s ve internal lters must be cleaned regularly and are
located in the locations listed in the following diagram. Twist the
lters to remove them then clean and replace in original locations.
If a lter is torn or damaged, replace with a new one.
INTAKE
FILTER
REGULATOR
BY PASS FILTER
PUMP OUT
FILTER
VACUUM
STACK
FILTERS
(2)
SPEEDSTER® LTD3 TANK LATCHES
& PUMP HOUR METER
The rear latches can be unlatched from the lower half of the
unit to open it for internal repairs and cleaning. To unlatch, ip
and twist latches. The hour meter activates when the pump
is turned on. This helps monitor usage and when to make oil
changes. Refer to p. 24 for oil maintenance instructions.