Mytee MYT-S-300 User manual

1
Instructions for
S-300 Tempo™
General Information p. 2
Set Up & Operation p. 4
Parts & Pricing p. 7
Notes p. 10
13655 Stowe Dr., Poway, CA 92064
Model #
Serial #
Form # ADM-Tempo
10-17
Please read before use.
Register your product
at http://www.mytee.
com/support/register

2
Dear Customer:
Congratulations on the purchase of your new Tempo™ spotter. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
Keep in mind that the S-300 Tempo™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the S-300 will give quality performance for many years to come.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed in ac-
cordance with all local code and ordinances. Do not remove ground pin; if missing,
replace plug before use.
Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualied electrician or service person if you are
in doubt as to whether the outlet is properly grounded. Do not modify the plug
provided with the machine. If it will not t the outlet, have a proper outlet installed
by a qualied electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accesso-
ries. Call your local service center for repair parts or service. Please specify the
Model and Serial Number when discussing your machine.
Name Plate
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le
a freight damage claim.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or
death.
Is used to call attention to a situation that could cause severe personal injury.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, ba-
sic precautions should always be followed, including the following: Read all instruc-
tions before using this machine. This product is intended for commercial use only.
To reduce the risk of re, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjust-
ments or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around
sharp edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where ammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other
parts of this machine for this purpose.
14. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when cleaning on stairs.
16. To reduce the risk of re or electric shock, do not use this machine with a solid-
state speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may
apply to the safe disposal of liquids which may contain: chemicals, grease, oil,
acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Filling the Solution Tank
1. Fill the solution tank with the approved cleaning solution.
2. Do not ll up the solution tank completely: 1” should be left free at the top.
3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.
4. Always follow the dilution instructions on the chemical container label.
5. The temperature of the cleaning solution must not exceed 70°C/160°F.
Use only non-ammable liquid in this machine.
GENERAL INFORMATION
Figure 1
Grounding Pin
Grounded Outlet
Grounded Outlet Box
Adapter
Tab for Grounding
Screw
Metal
Screw
Figure 2 Figure 3

3
Pre-Operation
1. Vacuum carpet and upholstery and remove other debris.
2. Prespray if desired.
Setup
1. Fill solution tank with water or approved cleaning agent. For best results, ll
with warm water (140°). Replace vacuum tank.
Flammable materials can cause an explosion or re. Do not use ammable
solutions or materials in tank(s).
FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.
ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
2. Attach solution hose to quick disconnect (located front of machine). NOTE:
Make sure the quick disconnect snaps together rmly. As you do this, always
inspect hoses for cracks or fraying. Do not use if hoses are damaged.
3. Attach vacuum hose to recovery tank.
4. Plug machine’s extension cord into the power cord pigtail and a grounded
wall outlet. FOR SAFETY: Do not operate machine unless cord is properly
grounded.
Operation
1. Turn pump switch on.
2. Prime the pump by pulling up on the tool’s lever to release air in the line. Hold
lever until a steady ow of solution comes out of the wand.
3. Once pump is primed and there is pressure in the solution line, turn on heater
switch and wait 5-7 minutes for water to heat up. Spray solution until heated
solution is coming out.
4. Turn on vacuum and begin cleaning. Do two dry passes for every wet pass.
NOTE: When cleaning upholstery, always check manufacturer’s cleaning
instructions.
5. Work away from outlet and power cord to prevent cord damage.
6. Use a recommended foam control solution in the recovery tank to prevent
vacuum motor damage. Periodically check for excessive foam buildup in
solution tank, and recovery tank.
7. To clean heavily soiled areas, repeat cleaning path from different direction.
8. When vacuum tank is full, it is time to empty the dirty water from the recovery
tank, and rell solution tank.
9. After cleaning, relieve water pressure from tool before disconnecting hose
Squeeze trigger for ve seconds after turning main power switch off.
After Use
1. Unplug.
2. Empty solution tank and rinse it with clean water.
3. Inspect hoses and replace if damaged.
4. Empty the recovery tank.
5. Inspect solution lter. Clean or replace if damaged.
6. Store the machine in a clean, dry place.
7. Open recovery tank cover to promote air circulation.
8. Do not expose to rain. Store indoors.
9. Use Mytee System Maintainer to clean pump, heater, and solution lines and
remove build-up.
Maintenance Schedule
Maintenance item Daily Once a week
Clean and inspect Tanks
Clean and inspect Hoses
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee system maintainer
Remove and clean oat shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs
Inspect machine for water leaks and loose hardware
x
x
x
x
x
x
x
x
x
Troubleshooting
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker; reset circuit breaker.
Pump does not work properly.
1. Snap quick disconnects rmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and ush clean.
4. Filters clogged, remove lters and rinse clean with water.
5. If brass check valve is stuck replace valve.
6. Check pump wire. May need to reconnect wire.
7. Pump switch may need to be replaced.
8. If pump motor brushes are worn, replace pump.
Vacuum motor does not work properly.
1. Check that hose is tightly connected.
2. Make sure drain cap is tightened.
3. Check and clean foam lter located in recovery tank.
4. If water is coming out of vacuum motor, use a low foaming detergent.
5. Clean upholstery tool.
Machine Specications
Solution Tank 1 gallon (approx.)
Recovery Tank 1 gallon (approx.)
Vacuum Single 2-stage
CFM 97
Water Lift 85”
Pump PSI 55
Pump GPM 0.37
Power
Consumption 7 amps @ 115V 60Hz
Machine Weight 20 lbs.
Machine
Dimensions 20” x 9” x 20.75”
Power Cord 25’ 16/3
230V Conguration Information
Model Number S300-230
Power
Consumption 3 amps @ 230V 60Hz/50Hz
FAQs
Q: What comes standard with the S-300?
A: The S-300 comes with an 8’ Hose-n-Hose™ vacuum & internal solution hose
and the 8400P Air Lite™ Upholstery Tool attached.
Q: Where do I plug the machine in?
A: The S-300 requires a grounded circuit. Please note: GFI outlets may trip before
the breaker setting.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacuums to dry off. You should also run Mytee’s 3601 System
Maintainer through the system weekly to keep the hoses, pump, and heater clean
and free of debris.
GENERAL INFORMATION

4
FRONT BACK
INCLUDED ITEMS
1. 8400P Air Lite™ 4” Upholstery Tool
2. 8’ x 1.25” vacuum hose with internal solution hose
2
2
4
7
3
5
1
1
6
8
9
S-300 TEMPO™ SET UP & OPERATION
1. Vacuum hose
connection
2. Solution tank
3. Power switches
4. Power cord pigtail
5. Quick disconnect
6. Recovery tank lid
7. Carrying handle
8. Recovery tank
drain cap
9. 2” casters
FILL SOLUTION TANK
Fill the solution tank with water or solution of your
choosing. Be sure to follow the chemical manufacturer’s
instructions for mixing. For best results, ll with warm
water (140° F).
1

5
PUMP SWITCH VACUUM SWITCH
Plug the machine into a grounded wall outlet with the
included extension cord. Switch on the PUMP.
Switch on the VACUUM and begin cleaning.
S-300 TEMPO™ SET UP & OPERATION
CONNECT VACUUM & SOLUTION HOSES
Attach the male end of the solution hose to the Tempo’s™ quick disconnect, then connect the vacuum hose to the
Tempo’s™ hose port, both of which are located on the front of the machine.
2
34

6
FILTER
DEFOAMER SYSTEM MAINTAINER
Add defoamer in the recovery tank to reduce foam and
prolong the life of the Tempo’s™ vacuum motor .
Weekly ushing of the solution system with Mytee’s 3601
System Maintainer helps keep lines clean and prevents
chemical build-up, improving pump life, performance and
pressure.
To get the best performance out of the Tempo™, after
each job, twist off the recovery tank lid and clean off the
lter located on the vacuum stack.
S-300 TEMPO™ AFTER USE
EMPTY RECOVERY TANK
To empty the recovery tank, twist off the recovery tank
drain cap on the back of the machine to release recov-
ered uid.

7
Part prices are subject to change.
S-300 TEMPO™ PARTS & PRICING
REVISIONS
REV.
DESCRIPTION
DATE
APPROVED
OD
ORIGINAL DRAFT
2/2016
JFL
A
UPDATED PLUMBING
11/14/2016
ML
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
H246
screw, 8-32 x 3/8" SHCS, alloy, Black
2
$0.99 ea
2
H451
latch, S-300H
1
$17.99 ea
3
H230
screw, 10-32 x 1/2" phil pan head, s/s
24
$0.99 ea
4
H611
handle, S-300H, black
1
$25.99 ea
5
H304
screw, 8 x 5/8", phil oval, s/s
6
$0.99 ea
6
G030 lid, vac tank, 3.5", clear
1
$13.99 ea
7
G058
vac tank deflector
1
$8.99 ea
8
H664
filter strainer, spotter
1
$6.49 ea
9
H453
elbow, 90 deg, pvc, 90, 3/4" mpt x 3/4" slip
1
$4.99 ea
10
P610
vac tank, S-300H
1
$49.99 ea
11
G036
cap, 2.5" threaded, tethered
1
$3.49 ea
12
G004
gasket, vacuum motor
2
$8.99 ea
13
C316
vac motor, 2 stage, 115V, peripheral
1
$99.99 ea
14
H404
nut, hex, 3/8"-16
4
$0.99 ea
15
H384
washer, 3/8 flat, s/s 4
$0.99 ea
16
H637
caster, swivel, stem, 2", w/out lock
4
$7.99 ea
17
H273
nut, kep, #10-32 zinc
12
$0.99 ea
18
H484
plate, mounting, QD
1
$4.99 ea
19
P967A
plug, switch
1
$1.99 ea
20
H445
fitting, strain relief, w/ spring, 1/2" npt
1
$8.99 ea
21
E533
power cord, end, 25', 16/3
1
$35.49 ea
22
E515
switch, rocker, 2 position
2
$13.99 ea
23
H310
plate, switch, MyteeLite, 3 hole
1
$6.99 ea
24
B102
qd, brass, 1/4" f x 1/4" fpt
1
$17.99 ea
25
B166
fitting, brass, 1/4"mpt x 1/4" push-in
1
$9.99 ea
26
P612
base, S-300H
1
$59.99 ea
27
PH657-6
tubing, 1/4", nylon, blk
1
$1.99 ft
28
B140
connector, 1/4" push-in x 1/8" mpt
1
$7.49 ea
29
C378
pump, 55psi, 115V flojet
1
$41.99 ea
30
H250
bracket, set 55 psi pump
2
$4.99 ea
31
B110
adapter, brass, 1/4" sw barb x 1/4" fpt, w/gasket
2
$3.99 ea
32
H212
flat washer, 9/16"ID x 1 1/16"OD, AN960-C916
2
$0.99 ea
33
B107 nipple, brass, 1/4"m, hex
1
$3.19 ea
34
B119
filter, strainer, 1/4"
1
$3.99 ea
35
PH634-12
sol hose, 1/4" silicone braided, clear
1
$6.49 ft
36
B170
ferrule, 1/4" brass
2
$0.99 ea
37
B194
nipple, hex, 1/4" mpt x 1/8" mpt
1
$8.99 ea
38
B103
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
1
$4.49 ea
39
P611
sol tank, S-300H
1
$79.99 ea
40
H312
plate, connecting, MyteeLite
5
$6.99 ea
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
S-300
SHEET 1 OF 3
Tempo Spotter
9/2016
A
SCALE: 1:16
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
M.LaBarbera

8
S-300 TEMPO™ PARTS & PRICING
12
13
12
10
7
6
5
20
21
22
3
23
17
17
18
3
24
25
26
29
38
31
32 32 33 34
35
3
30
17
16
39
40
3
11
36
3
4
3
8
9
14
15
1
28
31
37
27
19
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
S-300
SHEET 2 OF 3
Tempo Spotter
9/2016
A
SCALE: 1:16
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
M.LaBarbera

9
S-300 TEMPO™ PARTS & PRICING
1
2
3
4
5
6
7
8
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
B101
qd, brass, 1/4" m
1
$8.49 ea
2
B104
bushing, brass, 1/4" mpt x 1/8" f
1
$1.99 ea
3
AH135
sol hose, 1/9" x 97", (OAL), m
1
$36.99 ea
4
8400P
Air Lite
1 $114.99 ea
5
G079
hose wrap, heat guard
1
$2.99 ea
6
H360
vac hose, 1-1/4" x 8' 1
$19.99 ea
7
H133
Cuff-Lynx, 2" hose x 2" female
2
$3.99 ea
8
H943
cuff, black vinyl, hose, 1-1/4 x 1-1/4
1
$4.99 ea
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
S-300
SHEET 3 OF 3
Tempo Spotter
9/2016
A
SCALE: 1:16
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
M.LaBarbera

10
Mytee Products Inc.
13655 Stowe Dr.
Poway, CA 92064
www.mytee.com
© 2017 Mytee Products Inc.
Printed in the U.S.A.
NOTES