Namron ZIGBEE LED DIMMER 2.0 User manual

INSTRUCTION MANUAL
NAMRON ZIGBEE LED
DIMMER 2.0

NAMRON ZIGBEE LED DIMMER 2.0
1. WARNINGS AND CAUTIONS
Model No. 4512750,4512751
Rated Voltage 220-240V～
Rated Frequency 50Hz
Rated Wattage 300W
Load Range
Incandescent:15W-300W
LED/CFL:3W-200W
:3W-200W
:3W-100W
Dimming Method Phase-cut
Working Environment
Temperature：-10℃-35 ℃
Humidity：10% R.H. - 90% R.H.
Model Size 71mm×71mm×52mm
(L×W×H)
1.1 Risk of fire and electrical shock, the dimmer should be installed in accordance with appropriate
electrical codes and regulations.
1.2 The dimmer should be protected by a 16A maximum miniature circuit breaker.
1.3 Turn power off at circuit breaker or fuse and test that power is off before installing.
1.4 After install the dimmer, it is recommended to set the minimum brightness level to make bulbs
turn on immediately.
1.5 If you are unsure about any part of these instructions, consult a licensed electrician.
1.6 To reduce the risk of overheating and possible damage to other equipment, do not install to con-
trol a receptacle, a motor-operated appliance or a transformer-supplied appliance.
1.7 Use with compatible dimmable LED, CFL bulbs, Incandescent or halogen bulbs only.
1.8 When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either
LED, CFL or incandescent. Using the same model of each bulb will enhance dimmer performance.
1.9 This product complies to EN60669-2-1.

2. Splicing Design
3. Functional Specifications
3.1 Status Indicator
3.1.1 Indicator lights blue and flash: Enter to Zigbee mode connection.
3.2 Input and Output Terminals
3.2.1 N: Input terminal (Connect the neutral and live wire “N”)
3.2.2 L: Input terminal (Connect the live wire “L”)
3.2.3: Output terminal (Connect the bulbs)
3.2.4 P: Signal input terminal (Connect the self-reset switch-output terminal)
3.3 Push-button Rotary Switch
3.3.1 Turn on: Short press one time when in OFF.
3.3.2 Turn off: Short press one time when in ON.
3.3.3 Dimming:
a. Turn clockwise to increase the brightness.
b. Turn counterclockwise to decrease the brightness.
c. Long press to adjust the brightness when in ON status.
Release and long press again to change the direction of the dimming brightness.
3.3.4 Continuous short press two times when in ON/OFF can quickly turn to the full brightest.
3.3.5 Setting the ideal min brightness when in on status,continuous short press six times and the
lamp flash three times.
3.3.6 Setting the ideal max brightness when in on status,continuous short press eight times and the
lamp flash three times.
3.3.7 Network mode: Continuous short press seven times when in ON status.
Operation Component
Drive Component
Panel
②Input and Output Terminals
③Push-button
Rotary Switch
①Status Indicator
Short press: Within 0.5s
Long press: Over 0.5s
Continuous short press: Each interval of short press should
within 1s

4. Tools Needed To Install e Dimmer
then the APP can connect the dimmer when the bulb flash once and the status indicator turn blue
and flash. (①If failed to connect,APP will exit the network mode after three minutes.②During the
network connection,the lamp may flicker if the light is in the brightest.After the network is success-
fully configured or the network is been withdrawn, the lamp will return to normal).
3.3.8 Continuous short press nine times when in on status and the lamp flash five time to clear the
setting brightness(min or max).
3.3.9 Restore factory Settings: Continuous short press ten times when in ON and the lamp flash
once.
5.Installation
5.1 WARNING: To avoid fire and electrical shock, TURN PFF POWER at circuit breaker or fuse and
test that power is off before wiring.
5.2 Choose the connection of 5.3.1 or 5.3.2 to install the dimmer per your requirement. *The wire
core cross-sectional area of the terminals is 0.75 mm² - 1.5mm²,stripping length is 9mm.
5.3 Typical wiring application
5.3.1 Live Wire
5.3.1.1 1-Way
5.3.1.2 Multi-way
Ø5mm Philips Screwdriver Test pencil
Plier
Ruler
Electrical Tape
Cutter
△
!
L
N
NOTE:
(a)The dimmer should be connected to the electricity side of the load to
ensure normal work.
(b)The dimmer support to connect with multiple self-reset switches
(20pcs at most) to control the UP/DOWN and ON/OFF at the same
time.
(c)Two or more dimmers should not be connected in parallel or series
to control the same load from two different locations.
Multipl self-switches control one dimmer wiring diagram
L
N
Push switch
(Self-reset
switch)
Push switch
(Self-reset
switch)

5.3.2 Neutral and Live Wire
5.3.2.1 1-Way
Oneself-resetswitchcontrolmultipledimmerswiringdiagram
L
N
Push switch
(Self-reset
switch)
Multipleself-resetswitchescontrolmultipledimmerswiringdiagram
L
N
Push switch
(Self-reset
switch)
Push switch
(Self-reset
switch)
L
N
5.3.2.2 Multi-way
NOTE:
(a)The dimmer should be connected to the electricity side of the load to
ensure normal work.
(b)The dimmer support to connect with multiple self-reset switches (20pcs
at most) to control the UP/DOWN and ON/OFF at the same time.
(c)Two or more dimmers should not be connected in parallel or series to
control the same load from two different locations.

5.4 Installing dimmer
5.4.1 Divide the dimmer into two parts.
(Operation Component,Panel and Drive Component)
5.4.2 Carefully position all wires inside the wall-box, leaving enough space to insert the dimmer housing.
5.4.3 Put the Drive Component inside the wall-box and align at the screw holes(①②)
5.4.4 Tighten the screws(①②) to let the Drive Component stick to the Junction Box.
Multipl self-reset switches control one dimmer wiring diagram
L
N
Push switch
(Self-reset
switch)
Push switch
(Self-reset
switch)
One self-reset switch control multiple dimmers wiring diagram
L
N
Push switch
(Self-reset
switch)
Multiple self-reset switches control multi-way dimmers wiring diagram
L
N
Push switch
(Self-reset
switch)
Push switch
(Self-reset
switch)
②
60mm
60mm
①
电源和执行组件
Drive Component
Junction Box

Table 1 1-way application function
5.4.5 Install the Operation Component to the Fixing Panel and put them together to the Drive
Component.
6. User Instructions
6.1Function Instructions
F
Function Dimmer Operation Way Dimmer
Operation
App
Operation
Network Mode
Continuous short press the push-button rotary
dimmer seven times √×
ON/OFF Short press the push-button rotary switch one
time √√
h
c
tiwsy
r
a
t
or
n
ot
tub
-h
su
peht
nru
Tg
n
immi
D√√
Quicklyturntothefull
brightest
Continuous short press the push-button rotary
switch two times √√
Set the min brightness Continuous short press the push-button rotary
dimmer six times √×
Set the max brightness Continuous short press the push-button
rotary dimmer eight times √×
Clear the setting(min or
max ) brightness
Continuous short press the push-button rotary
dimmer nine times √×
Restore factory Settings Continuous short press the push-button rotary
switch ten times √×
×
ONff
o/
n
o
el
ude
hcS √
Share device NO ×√
Group control NO ×√

6.2 Priority
The operation of self-reset switch could stop the operation of APP,
when at the operation of self-reset switch, APP operation could not work.
F
Function Dimmer Operation Way Dimmer
Operation
Self-reset
Switch
Operation
App
Operation
Network Mode
Continuous short press the
push-button rotary dimmer seven
times
√××
ON/OFF Short press the push-button rotary
switch one time
√√ √
Dimming Turn the push-button rotary switch √√ √
Quickly turn to the full
brightest
Continuous short press the
push-button rotary switch two
times
√√ √
Set the min brightness Continuous short press the
push-button rotary dimmer six
times
√××
Set the max
brightness
Continuous short press the
push-button rotary dimmer eight
times
√×
×
Clear the setting(min
or max ) brightness
Continuous short press the
push-button rotary dimmer nine
times
√××
Restore factory
Settings
Continuous short press the
push-button rotary switch ten
times
√×
×
×
×
O
N
ff
o/
n
o
eludehcS √
Share device NO ×× √
Group control NO ×× √

7.Troubleshooting
P
Problems Possible Cause Solution
Lights flickering Lamp has a bad connection. Reconnect and fix the
wires.
The brightness of the lamp
varies
One dimmer been connected
to multiple types bulbs, incur
interference and cause flicker.
Change bulbs to same
type.
LED and CFL flickers at low
end of dimming range. Load compatibility is not good. Turn up lamp minimum
brightness properly.
Lights does not turn on
Circuit breaker has tripped. Turn power on
Fuse burn out Change fuse
Lamp burned out Change lamp
Lamp neutral connection
is not wired Reconnect the lamp neutral
hctiwsrewopehttratseRlamronbAlortnocfotuosthgiL
Importer:
Namron AS
Nedre kalbakkvei 88 B
1081 Olso
Norway
Made in China