NAUTICA J-CLASS User manual

English Version
User Manual
CONSUMER WARRANTY
& SERVICE INFORMATION
SEE NEXT PAGE
230532
Distributors ONLY warrant products with an active
Warranty Registration
ALWAYS ACTIVATE YOUR WARRANTY IMMEDIATELY ON
https://nauticaseascooters.com/pages/warranty
Distributors in the United States and Canada provide a Standard Limited Warranty
for 6 months from the date of purchase for new products. If you're not located in
the United States or Canada, please contact your Local Distributor for warranty
arrangements in your territory. Please visit www.seascooter.net for Distributor /
Service Center details. Distributors ONLY warrant NAUTICA Seascooter products
purchased from an authorized dealer and with an original purchase receipt. All
warranties are limited to a single original owner on the purchase of new and
current product from an authorized reseller. Closeouts, Discontinued and
Secondary sales of any kind including “like new” or out of box are not eligible for
warranty consideration.
This warranty gives the consumer specific legal rights, and those rights may vary
from place to place. Ask your Local Distributor for the warranty period in your
region by calling their Service Center. Any part of the product supplied by the
Distributor and found in the reasonable judgment of the Distributor to be defective
in material or workmanship will be repaired or replaced then returned by the
Distributor without charging for parts and repair costs. The product including any
defective part must be sent to the Distributor within the warranty period. The
customer will pay for the expense of delivering the product to the Distributor.
This warranty does not cover any product that has been subject to misuse
negligence or accident, or that has been operated in any way contrary to the
operating instructions as specified in the User Manual. Any flood, loss or damage,
for any reason, that is caused by accidental release and sinking of the unit, or
from flooding an o-ring sealed or water tight area will not be covered under
warranty. This warranty does not apply to theft, loss, abuse or tampering, lack of
maintenance, improper storage, exposure to excessive temperature, extended
sunlight, material interactions, deteriorating chemicals or fumes, any damage to
the product that is the result of improper maintenance or parts replacement
performed by someone other than the official Distributor Service Center or to any
product that has been altered or modified so as to change its intended use. This
warranty does not extend to repairs made necessary by normal wear or by the use
of parts or accessories which are either incompatible with the product or
adversely affects its operation, performance or durability.
ELECTRICALLY OPERATED PRODUCT
Not for children under 16 years of age. As with all
electrical products, precautions should be observed during handling
to reduce the risk of electric shock.
CAUTION

FCC Statement
(For USA Regulation Only)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy,if
not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.

Introduction
The dual thruster NAUTICA J-CLASS is a full-featured Seascooter
that gets you cruising underwater with a top speed of up to 5mph
(8km/h). Easily shift between 3 rotational speeds as you conserve
your energy for more bottom time.
Use appropriate equipment such as wetsuit, approved life
jacket, mask & snorkel etc. when using Seascooter.
Only operate the Seascooter in water.
• Innovative patented foldable design provides excellent carry-on
travel qualities and compact storage size
• Water -proof patented motor built for extended use
• Durable watertight construction
• Runs up to 40 minutes
• Rated to 130ft / 40m
• Speed up to 5 MPH / 8 KM/H
• 3-level rotational speed control
• LCD display with battery level and Gear indicator
• Powered by high performance replaceable Lithium-Ion battery
• Weighs only 15 lb / 6.8 kg including battery
Contents
Introduction 1
Warnings 2
Parts Diagram 6
Battery Instruction 7
Getting Started 10
Battery Use 14
Mount 17
Camera Assembly 18
Care & Maintenance 19
Technical Specifications 20
Discarded electrical appliances are
recyclable and should not be discarded
in the domestic waste! Please actively
support us in conserving resources and
protecting the environment by returning
this appliance to the collection centers
(if available).
1
• Keep the manual since it contains important information.
• When passing on this device, include the user manual and
all relevant warning information and parts.
• It is the responsibility of the owner to give proper
instruction and precaution (regarding the risk associated
with this device) when lending the device to other people.
The Seascooter is designed for use in seawater. It will
have less buoyancy in fresh water, lake or pool and
may sink in such waters.
User manual is also available in PDF format,
contact your local distributor to a copy if needed.
WARNING

2 3
• This is not a life saving device.
DO NOT use it as a buoyancy aid.
• Read the User Manual carefully before using
the product.
• Always ensure sufficient charge remains in the
battery to return to the shore surface before using
the Seascooter.
• Do not use alcohol or mind-altering drugs prior to and
during use of this product.
• A child under 16 years old should never operate
this product.
• The Seascooter is designed for 1 person use.
• ALWAYS inspect the swimming area to ensure it is
free of hazards or obstacles such as boats or
swimmers before using the Seascooter.
• Be aware of appropriate water levels, tidal changes,
dangerous currents, weather change and strong
offshore winds. ALWAYS scout unfamiliar water before
venturing out.
WARNING
• Never place body parts, clothing or other objects in
the vicinity of the propeller. Do not wear loose or
flowing clothing or equipment that could be drawn
into the propeller.
• Particular care should be exercised when using the
Seascooter near anybody with long hair. Users with
long hair should tie it up or wear a swimming cap
when using the Seascooter.
• ALWAYS wear a life vest (personal floatation device - PFD)
approved by your local authorities for Snorkeling (U.S.
Coast Guard Type III vest in the US or Canadian Coast
Guard approved life vest in Canada or SAI Approval PFD
in Australia or CE Approved PFD in Europe).
• Do not attach your body, clothing, other equipment to the
seascooter in any way.
• Be careful when you are transporting the Seascooter and
setting it down to avoid crushing hazard on hands, foot
or toes.
• Crushing / Cutting Hazard

4 5
• NEVER remove the grilles except for maintenance.
• Familiarize yourself with the Seascooter functions and
battery life before embarking on any dives or excursions.
• Always charge battery to its fullest before using the
Seascooter.
• Do not allow sun tan oils or lotions to be in prolonged
contact with the Seascooter plastic as it may cause the
plastic to become brittle and break apart.
• ALWAYS keep the Seascooter out of direct sunlight
when not in use. HEAT KILLS BATTERIES AND IT MAY
EXPLODE OR LEAK.
• Never open the Battery Compartment of the Seascooter
in the water.
• When not in use, always turn the Master Switch to the
OFF position.
• Do not use the Seascooter below the recommended
maximum depth of 130ft / 40m.
• This machine is not intended for mixing or working with
sand, concrete and material with similar physical
characteristics. This machine is only intended for
swimming and diving in the water.
• Do not use the unit if it is damaged in any way.
• Replace the battery immediately if it is damaged.
• The Seascooter should only be used for scuba diving by
qualified divers.
• When using the Seascooter for scuba diving, ascents
and descents should be made in accordance with
recognized diving practices.
CAUTION
• Due to safety considerations those who have not
obtained a C-Card (attesting to completion of training)
from an entity providing diving instruction must not
under any circumstances use this product for diving.
• In different waters (seawater, lake, pool) and
conditions such as currents, temperature and pressure
can affect the buoyancy of the unit which may cause
the unit to sink if accidentally released.
• DO NOT release or leave the Seascooter in the water.
Always take the unit out of water when not in use.
• Adequate lighting shall be used when using the
Seascooter in dark waters and during night diving.
• Before each use, always check the handles are in
locking place.
• Always check that your Seascooter works properly
before use.
The following action during assembly, disassembly,
and transportation of the Seascooter may incur
crushing hazards to your fingers or toes:
• Opening and closing the foldable control handles.
• Installing the battery.
• Setting down the Seascooter or battery.
• Accidental dropping of the Seascooter or Battery.
CRUSHING HAZARD:

Fig.1
1 7
8
9
10
2
3
11
4
5
6
16 14 15
Parts Diagram
6 7
Battery Instruction
Replace the battery immediately if it is damaged.
· The instructions concerning persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge
and children playing with the appliance are not
applicable.
· The connector must be removed before the
appliance is cleaned and that the appliance inlet
must be dried before the appliance is used again.
· Detachable power supply part shall be provided with
the part of class III construction of the appliance.
· The transformers or battery chargers used with the
product are to be regularly examined for damage to
the cord, plug, enclosure and other parts, and in the
event of such damage, they must not to be used
until the damage has been repaired.
Charging instruction
1) Connect the battery pod to the charging base (Fig.2)
2) When charging, LED light of the charger turns Red (Fig.2)
3) Charging will take around 3-4 hour. When the battery is
fully charged, LED light turns Green (Fig.2)
4) When battery is fully charged, unplug the charger from
the mains (wall socket) and remove the battery from
charging base.
WARNING
1. Master Switch
2. Camera Mount
3. Main Body
4. LCD Screen
5. Foldable Handles
6. Handle Locks
7. Start Buttons
8. Thruster
9. Safety Net
10. Indicators
11. Battery Door
12. Charger
13. Charging Base
14. Battery
15. Multipurpose Mount
16. Propellors
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
12 13

8 9
Battery Instruction Battery Instruction
Battery installation:
1) Ensure the master switch is in off position (Fig.11).
2) Always ensure the seascooter is out of water, dry and
placed in dry area.
3) Release the battery door locking screw according to Fig.3
step 1.
4) Slide out the battery door (Fig.3 step 2).
5) Make sure the terminals 0-rings on the battery and battery
compartment are in its position, clean and dry (Fig.9).
6) Align the groove on the battery and the tongue inside the
battery compartment, slide in the battery (Fig.4).
7) Lock the battery (Fig.5 step 1,2,3).
8) Close the battery door (Fig.6 step 1).
9) Lock the battery door (Fig.6 step 2).
To remove the battery for charging:
1) Unlock the battery (Fig.7 step 1,2).
2) Pull out the battery (Fig.8).
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
Battery
Battery Handle
Charging
Base
Match key slot
to load down
battery to the
charging base
Charger
LED Light
Fig.7 Fig.8
Fig.9
1
2
34
1,2,3,4 BATTERY
SEAL RINGS
Fig.2 Fig.3
1. Turn locking screw
counterclockwise
to unscrew
battery door 2. Slide battery
door up to remove
Fig.4 Fig.5
Slide battery in with
battery guiding slot
inline with guiding rib
Guiding tongue Guiding groove
Fig.6
1. Slide battery door down
2. Turn locking screw clockwise
to lock up battery door
1. Pull and
flip battery
latch out
2. Pull and flip
battery handle out Grip battery handle to pull battery out
1. Match inner
latch to the
battery slot
2. Push to rotate outer
latch to lock up battery
3. Latched
position

1. After battery installation, fold out the seascooter (Fig.10 step 1,2).
2. Lock the folded-out handles with the metal clips (Fig.10 step 3,4,5).
3. Slide the master switch to on position (Fig.11).
4. LCD dashboard will be switched on once master switch is in on position
(LCD will be switched off if seascooter is idle for 8 minutes. Slide the Master
Switch OFFand ON again to quit idle mode.)
5. Pull both triggers to start the propellors (Fig.11)
6. Release and press 1 trigger again to change the speed.
Attention: (Refer to Fig.12)
1) Seascooter should only be run in water. It will only run for 3 seconds if in air.
In such case “pictogram A” will be shown on the LCD screen
2) Seascooter should only be triggered when the handles are fully folded out.
Otherwise, “pictogram B” will be shown on the LCD screen.
3) Seascooter should only be triggered when the propeller grilles are installed
and locked. Otherwise, “pictogram C” will be shown on the LCD screen.
LCD display:
Low speedBattery capacity
indication
FIG-12
ABC
D
Full Screen
High SpeedMedium speed
“pictogram A”: When it is blinking, means you are not running the seascooter in
water.
“pictogram B”: When it is blinking, means the seascooter handles are not fully
folded out.
“pictogram C”: When it is blinking, means the grilles are not installed or locked.
“pictogram D”: When it is blinking, means there is leaking of water in your
seascooter. In such case, the motor will run for 9 seconds then stop for 1 second
with beeping sound. Return to shore immediately and contact the service center
for repair.
1110
Getting StartedGetting Started
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
Keep fingers away from gaps when folding the seascooter.
WARNING
Fig.10
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
Flip left/right latch pins
to engage to the hooks
Unfold
Procedures
Left/right latch pins
engaged to the hooks
Fig.11
MASTER
SWITCH
ON OFF MASTER
SWITCH
Push left/right lock
levers back down to
lock up both handles
Flip until two
handles stay inline
2. Flip both
handle backward
1. Flip both
handle locks open
FIG-14
FIG-15 FIG-16
FIG-13
d
Underwater Detection
Handlebar Detection
Nozzle Front Cap Detection
High Speed Zone
Medium Speed Zone
Low / Medium / High Speed
Low Speed Zone
Battery Level Bar
% Battery Capacity
Water Ingress Detection
(Blinks)
Error Code (Blinks)
Trigger Trigger

12 13
Getting Started Getting Started
Do not put your hand or any other things into the propeller.
Notes:
1. If there is no operation for a long time, the product
will be turned off automatically. Please turn off the
master switch before you put it away.
2. Please do not replace the battery in water.
Please remove the battery and clean the machine with
fresh water after using, and keep the machine in cool
and ventilated place.
Please use the machine correctly as shown and
do not use in reverse.
WARNING
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
Fold Procedures
Push locking
lever to the front
and disengage left/right
latch pins from the hooks
Flip left/right
latch pins backward
to allow handle to fold
Flip both handles
to the front
Flip until two thrusters
stick together
1. Push safety
lock plate to the front
2. Lift locking lever
up to release the lock
To fold up and hand carry the seascooter:
• Press and hold the clip on the middle of metal lock, then pull out the
lock according to Fig.18 step 1,2,3.
• Fold the handles to the front (Fig.18 step 4,5).
• Carry the seascooter with the carry handle (Fig.19).
Fig.17
Fig.19
Fig.18

14 15
Battery Use Battery Use
• MUST re-charge the battery after
EACH USE.
• MUST re-charge the battery
at least EVERY SIX MONTHS when
not in use.
• ALWAYS REMOVE the Battery from
the seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries
discharged for long - the batteries do
self-discharge and the charge could drop
low enough to damage the battery.
• Keep Lithium-Ion batteries away from
high heat - high temperatures may cause
premature battery failure.
• ALWAYS store Lithium-Ion batteries
partially discharged in a cool, dry place.
RE-CHARGE THE BATTERY
6
AT LEAST
EVERY
MONTHS
www.seascooter.net
WARNING
BATTERY SAFETY
CAUTION
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
CAUTION

1716
J-CLASS comes with a camera mount and a
multi-purpose mount. Install and exchange the mount
according to below diagram.
Battery Use Mount
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
CAUTION
Fig.20
Matching key and slot
Matching key and slot
Unscrew to replace
Unscrew to replace

Thumb Screw Waterhousing
18 19
Washing and Care
• After each use, immerse the seascooter into a container
filled with freshwater for 20 minutes. Then switch on the
seascooter in low speed for 3 seconds, and repeat this
function 5 times to wash away dirt and salt from the
product and motor.
• Dry the seascooter after washing. To dry the seascooter,
remove the battery and leave the battery door opened.
Turn the seascooter in different angles to drain the water.
Use a dry cloth to dry the seascooter. Put the seascooter
in a cool and ventilated area overnight for drying.
• Make sure the seascooter is fully dry before storage.
• To clean the Seascooter do not use detergents; only use
a damp cloth to wipe the unit clean.
• Use a cloth to dry the Seascooter and the battery
compartment.
• DO NOT leave the Seascooter in the water. Always take
the unit out of water when not in use.
Sand or Grit on Seals
Ensure that sand/grit does not get on the seals as correct
maintenance and care is essential. To remove sand or grit
from the seals, rinse the seals in fresh water and apply
fresh lubricant. If there is sand inside the Battery Housing,
gently brush the sand from the unit taking care not to
scratch the sealing surfaces.
Camera Assembly
To attach your camera to Seascooter J-CLASS, you will need a
thumb screw or hardware depending on the mount you are using.
Blocked Propeller
If the Propeller becomes blocked, you can remove the front grille
to remove an obstruction. Below steps must be following to
avoid injury.
(Under normal use the grilles must not be removed.)
1. Remove the SEASCOOTER from the water.
2. Make sure the master switch is in the Off position.
3. Dry the seascooter and remove the battery.
4. Open the grille according to the Fig.21 step 1.
5. Remove obstruction.
6. Reassemble grille (Fig.21 step 2,3).
ATTACHING YOUR CAMERA TO SEASCOOTER MOUNTS
(Can be used with GoPro®HERO [3, 3+, 4, 5, 6 or 7] cameras, or
other camera with using the same mount system)
*Camera (and Waterhousing), Attachment Buckle and Thumb Screw are not included
Care & Maintenance
Simply attach the Camera to the mount
and align the hole, Insert And Tighten Up
The Thumb Screw
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
Fig.21
1. Remove screws and pull out front grilles
2. Matching cup/cone to reinstall front grilles
3. Front grilles back in places
and fasten screws tight.

3-4 HOURS
RECHARGE
22.2V / 6 AH
BAT TERY
3 SPEED
GEAR
5 MPH / 8 KM/H
SPEED UP TO
CARRY-ON TRAVEL
SIZED FOR
40 MINUTES
RUN TIME
15 LB / 6.8 KG
WEIGHT
130 FT / 40 M
DEPTH
P
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
Technical Specifications
26.2 inches x 6.7 inches x 11.8 inches
665 x 170 x 300 mm
Unit Dimensions
Unit Weight
15 lb (6.8 kg)
Battery Type
1 x 22.2V / 6 AH rechargeable battery
Speed
Up to 5 mph (8 km/h)
Depth rating 40 m / 130 ft
(Maximum advised depth rating for
recreational diving)
Battery Life /
Fully Charge
Runs up to 40 minutes with normal use.
Continuous use up to 30 minutes.
*Normal Use
The definition of normal use is based on the average general
time of use the user activates the Seascooter in the water.
∆Continuous Use
The definition of continuous use is based on a fully charged
battery whereby the Seascooter is used continuously in the
water without stopping.
US & CANADA MARKET ONLY
Toll Free (US) : 1-800-678-7873
[email protected]
nwww.Nauticaseascooters.com
(US & CANADA MARKET ONLY)
Patented
Print in China
For more information on
Seascooter™Products
(Warranty, Customer Care / Maintenance,
Parts & Battery Purchase)
PLEASE VISIT
www.Nauticaseascooters.com
Please visit our website at www.Nauticaseascooters.com to find out your local distributor.
This Product is not manufactured by Nautica. For consumer purposes,
please contact Sport Dimension Inc. at 1-800-678-7873.
All corresponding specification appear in this manual are correct at the time of printing.
For the latest updates and further information on the complete range of the Seascooter™,
PLEASE VISIT www.Nauticaseascooters.com
Nautica™and ™ are trademarks of Nautica Apparel, Inc.
©Nautica Apparel, Inc. nautica.com
20

• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
In addition, this warranty does not cover items that
experience normal wear and tear.
ALL IMPLIED WARRANTIES ARE LIMITED IN THE DURATION TO THE
WARRANTY PERIOD. AND SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
OTHERWISE, ARE DISCLAIMED IN THEIR ENTIRETY AFTER THE
EXPIRATION OF THE APPROPRIATE WARRANTY PERIOD. THE
DISTRIBUTOR’S OBLIGATION UNDER THE WARRANTY IS STRICTLY
AND EXCLUSIVELY LIMITED TO THE REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS AND RETURN OF THE PRODUCT TO THE
CUSTOMER. THE DISTRIBUTOR DOES NOT ASSUME OR AUTHORIZE
ANYONE TO ASSUME FOR THEM ANY OTHER OBLIGATION.
THE DISTRIBUTOR ASSUMES NO RESPONSIBILITY FOR INCIDENTAL,
CONSEQUENTIAL OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED
TO EXPENSE OF RETURNING THE PRODUCT TO THE DISTRIBUTOR,
LOSS OF USE OF PRODUCT AND LOSS OF TIME OR INCONVENIENCE.
THIS PRODUCT IS DESIGNED AND INTENDED FOR PERSONAL
RECREATIONAL USE ONLY!
THIS PRODUCT IS NOT WARRANTED FOR COMMERCIAL OR
RENTAL USE!
REPAIR WORK OR DELIVERY OF A REPLACEMENT DOES NOT
EXTEND OR RENEW THE WARRANTY PERIOD.
WARRANTY SHALL AUTOMATICALLY BE VOID IF DAMAGE IS
RESULT OF NON-ORIGINAL PARTS.
LIMITED WARRANTY for seascooters with camera mount:
• ALWAYS inspect to ensure the product works properly every time before
use. Warranty of this product does not cover any damages due to misuse.
• Failure to follow the user(s) instructions on packaging and/or user(s)
manual may result in damages or loss of your cameras including but not
limited to any user’s personal items, all of which are not covered under
warranty of this product.
• Use at your own risk. Manufacturer(s) and/or suppliers/agents are not
responsible for any damages/repairs, loss to cameras/electronic items
including but not limited to any user’s personal items directly and/or
indirectly resulted in the use of this product. Damage(s) resulting from any
use, misuse, accident, and normal wear and tear are understandably not
covered under this product warranty nor be responsible by manufacturer(s)
and/or suppliers/agents.
EXCLUSIONS
BATTERY. This warranty does not include the battery.
Never replace the original SEASCOOTER BATTERY with an
AFTERMARKET BATTERY. Seascooter with aftermarket battery will not be
covered by this warranty.
For any questions or queries you may have regarding your
SEASCOOTER™, please follow the below steps for easy and
fast resolution:
- STEP 1-
Please read your User Manual. For a copy of the User Manuals, please visit
www.Nauticaseascooters.com
- STEP 2-
Go to www.Nauticaseascooters.com and see our FAQ section to find instant
answers.
- STEP 3-
Contact one of our Customer Service representatives at the Customer Service
Center in your region.
CUSTOMER ENQUIRIES
If your unit is not operating, please refer to your User Manual before
contacting our Customer Service Center. For any damage or repair work
required, please do not return your product to the store where it was
purchased.
RETURN / REPAIR POLICY
Customers must contact their Local Distributor Service Center to ask for an
official Claim Form. The Claim Form must be returned with the customer’s
contact details and a photo of the Seascooter, defective parts, the serial
number and the Original Purchase Receipt. The Distributor Customer Service
Center will review the case and issue a Return / Repair Authorization Number
before sending the product to the Distributor Service Center. Returned
products must be shipped with original packaging including the polystyrene
packing material and all defective parts. Please contact your Local Distributor
Service Center for assistance in handling your case.
Please visit our website www.Nauticaseascooters.com
for a listing of most update distributor contacts and
service center contacts.
RETURN / REPAIR PROCEDURE
1. Call the Customer Service Center for your Return / Repair Authorization
Number.
2. Make a copy of your Proof of Purchase (receipt).
3. Pack the defective unit in its original packaging including the polystyrene
foam and include the unit and all defective parts.
4. Attach the copy of your Proof of Purchase (receipt) to the outside of the box
(clearly visible), together with the Return / Repair Authorization Number.
5. Ship the package to the Service Center on your cost.
PLEASE NOTE: Deliveries that do not have the Proof of Purchase (receipt)
and Return / Repair Authorization Number attached clearly to the outside of
the box, will not be accepted by the Service Center.