YUNEEC GB200 Instruction manual

QU ICKSTART MANUAL (ENGLISH)
TABLE
OF CONTENTS
1 Table of Contents
2 .................... Warnings andImportantNotes
4 Overview
6 How
to switch Camera Mounts:
CGOl ™ to GoPro3/ 3+
7 How to switch Camera Mounts:
GoPro3/
3+ • to CGOl ™
9 Mounting
CGOl™ on GB200™
9 MountingGoPro• on GB200™
9 .................... Mounting
GB200 ™ on Blade• 3500X2
13
GB200™ LED Status
14 Spare Parts and compatibleproducts
14 Troubleshooting Guide
16 ....... ........... . LimitedWarranty
Yuneec Exhibit 1037 Page 1

WARNINGS AND IMPORTANT NOTES
Warning: Do not move, sway or shake the model during the
initialization process. Moving, shaking or swaying the model
during the initialization process may lead to initialization failure,
which will require you to cyde the power off and then back on to
repeat the process. Adjusting or modifying the GB200™ in anyway
is not recommended. Prior to using the GB200™, read andunder-
stand the
quick start guide and instruction manual completely.
Always
power on your transmitter first and then power on your
model and gimbal.
YUN
EEC™ GB200™ gimbal is optimized for both the CGOl™
andGoPro3/3+" cameras. Please mount your camera to the
GB200™ without adjusting or modifying the GB200™. Do not
modify or add any other component I device (such as filters,
lens, plastic
case, hood, etc.) to the camera. Also, it~ important
to makesure to use the original batteryfor yourchosen camera, or
the change
in weight and center of grav ity of the camera mayde-
crease performance of GB200™ oreven cause internal malfunction.
Make sure
your model's autopilot system operates in the safest
manner when the
main power battery is connected. We strongly
recommend thatyou remove all blades/propellers, use a suitable
flight battery, and keep a safe distance from children and other
people during gimbal setup. Please follow these important steps
to
mount and connect the GB200™ gimbal on your model, and
respect the AMA's National Model AircraftSafety Code.
2
Yuneec Exhibit 1037 Page 2

YUNEEC™ has no control over theuse, setup, final assembly or
modification(including
use of non-specified YUNEEC™ parts i.e.
motors, flightcontrollers, motorcontrollers, blades/propellers,
etc)
or misuse. Therefore no liabilityshall be assumed noraccepted for
any resulting damage or injury. By the act of use ,setup or assembly ,
the
user accepts all resulting liability. YUNEEC™ assumes noliability
for damage(s) or injuries incurred directly orindirectly from the
use of this product.
YUNEEC™ and GB200™ are trademarks or registered trademarks of
Yuneeclnternational Co., Ltd .. This productand manual are copy-
rights of
YU NEEC™ with all rights reserved. No pa rt of this product
or manual shall be reproduced in any form without the prior
written consent or authorization from YUNEEC™. Furthermore,
noother liability
is assumed with respect to the use of the product
or information contained herein.
YUNEEC™ reserves the right to
update manuals and quickstart guides any time. For warrantyinfor-
mation,
please visitwww.Yuneeccom
3
Yuneec Exhibit 1037 Page 3

OVERVIEW
Universal
PWM Inpu t
Bl ad e" 35 0CiX
Camera Pitch
Co nt ro! Po rt
DIFFERENCE BETWEEN ANGLE ORVELOCITY MODE:
Angle Modeallows the'pitch' angle of the camera gimbal to be
changed relative to the
PWM control stick/knob/slider input.
Velocity Mode controls the speed/rate of the'pitch'angle
of the
camera according to
PWM control stick/knob/slider input. For
example, the morecontrol input the faster the rate of chan ge
will be.
4
Yuneec Exhibit 1037 Page 4

Software
UpdatePon
5
CG01 '"
Mo unt i ng screw
Yuneec Exhibit 1037 Page 5

ControlBoard
Cover
Pit ch A xis
Arm
Go Pro°Camera
Gi mb al Mount
HOW TO SWITCH CAMERA MOUNTS: CG01'" to GoPro3/3+0 (A)
S tep 1: Rotate the C GOl™ Gtmera mount -as shown in illu stration
A- until th e flat spot inside th e se ts cr ew hole is facing up, an d
loos
en the setscrew using the alien wrench.
Step 2: Carefully rem ove th e CGOl™ c am era mo unt by s lidi ng it
outwardawayfrom the gimbal motor
and remove the gyroboard
fr om the gyro board mount.
Step 3:
In se rt gyro board into the gyro board mo unt on theGoPro•
Gtmera mo
unt and wrap the gyro board wire harne ss cloc kwi se
one whole turn around th e e nd of th e camera mo unt toward the
gimbal motor.
6
Yuneec Exhibit 1037 Page 6

Step 4: Spin the gimbal motor shaft until the 'flat spot' is facing
the setscrew hole. Insert and tighten the setscrew to secure the
GoPro• mount to the GB200™.
HOW TO SWITCH CAMERA MOUNTS: GoPro3/3+0 to CG01'" (8)
Step 1: Rotate the GoPro• camera mount -as shown in illustration
B- until
the flat spot inside the setscrew hole is facing up, and
loosen the setscrew using the hex wrench.
Step
2: Carefully remove the GoPro" camera mount by sliding it
outward awayfrom
the gimbal motor and remove the gyro board
from
the gyro board mount.
Step 3: Insertgyroboard into the gyro board mount on the CGOl™
camera mount and wrap the gyro board wire harness dockwise
one whole turn around the end of the camera mount toward the
gimbal motor.
Step 4: Spin
the gimbal mot or shaft until the 'flat spot' is facing
the setscrew hole. Insert and ti g hten the setscrew to secure the
CGO l™mo unt to th e GB200™ .
7
Yuneec Exhibit 1037 Page 7

Il lu st ra ti on A
CGOl
'~ mo un t
I ll u st r at ion B:
G o P r o 3/3 + ~ mou nt
8
Yuneec Exhibit 1037 Page 8

MOUNTING CG01'" ON GB200 (C)
1. Remove the 5.8GHz Wi-Fi antenna from the CGOl ™.
2. Install the CGOl™ into theCGOl™ camera mount.
3. Connect the 5.8GHzWi-Fi antenna by pressing it onto the
5.8GHz antenna socket on the CGOl ™and tum it 90° to secure the
antenna to the
CGOl ™and camera mount.
4. Install the 3mm mounting screw to secure the CGOl™ to the
mount.
MOUNTING GOPR0° ON GB200'" (D)
1. Install GoPro3/3+• in the GoPro3/3+• mount
2. use the GoPro3/3+" mounting sleeve to secure the camera to the
mount. (see illustration)
MOUNTING GB200 '" ON BLADE" 350QX (E,F,G and H)
1. Ins tall the GB200™ gimbal mounting plate on the 35 0QX us in g
the (4) inclu ded screws.
2.S
lid e the GB200™ into pla cew ith thearm s id etoward the back
of the mode
l.
3.Connect the Blade• 350 QX2 control cab le to the camera pitch
control port on the
GB200™ and the co rr esponding port on the
Blade•
350QX V2.
4. Pla ce the Blad e• 350 QX2 on a flat and stable surface. Sw itch
on the Blade" 350 QX2 . Do not mo ve, sway or shake the model
during the automatic calibr
at ion process. Aft er the automatic
calibrat
ion is complete,your GB200™ is ready to use.
9
Yuneec Exhibit 1037 Page 9

Illustration C:
Mount ing CG01'"'
camera
Illustration 0:
Mounting GoPro
0
camera
Yuneec Exhibit 1037 Page 10

Illustra ti on E: Ins ta lling the mounting plate to Blad e" 350 QX2
Ill ust ra tion F:
Slidi ng <Xl200 '" i nt o
the
mounting plate
t
11
Yuneec Exhibit 1037 Page 11

Illu s tr a ti on G: Connecti ng the
Blade• 350 0X2 co ntrol caUe
on the Blad e• 350 0X2 Ill ustr ati on H:P oweri ng
12
Yuneec Exhibit 1037 Page 12

TIP: The pitch axis neutral position can be changed by holding
yourdesired pitch axis position within 5 seconds after the gimbal
initializes.
GB200'" LED STATUS
ANGLE CONTROL MODE: LED COLOR RED
1. PWM Control Input (port 2): the red LED will flash onc e and
become solid.
2. Spektrum• SatelliteReceiver inserted (port8/9): the red LED wi ll
flash twice and become solid.
ANGULAR VELOCITY MODE: LED COLOR BLUE
1. PWM Control Input (port 2): the blue LED will flash once
and become solid.
2. Satellite receiver inserted (port8/9): the blue LED will flash
twice and become solid.
13
Yuneec Exhibit 1037 Page 13

SPARE PARTS LIST
BLH7901 ............ . ..... Main Control Board w/ RX: 350 QX2
BLH7902 ............ . ..... White Battery Cover: 350 QX2
BLH7903 ............ . ..... Battery Frame: 350 QX2
BLH7904 ............ . ..... Gimbal Arms: GB200™
BLH7905 ............ . ..... Gimbal Motors: GB200™
BLH7906 ............ . ..... Gimbal Mount: GB200™
BLH7907 ..... ....... . ..... Gimbal Control Board: GB200™
BLH7908 ............ . ..... Camera mount CGOl™: GB200™
BLH7909 ............ . ..... Camera mount Go ~o Hero 3•: GB200™
BLH791 0 .................. GB200™ Brushless Gimbal
TROUBLESHOOTING GU IDE
WHAT WHY SOLUTION
Th e gimbal ke€ps Carnera may not be Check and make sure
vi l:xa tin g aft er mo unte d sec urely to c am er aismo unte d
initializing. the camera mount. com ple tely and secu-
rely in th e came ra
mo
unt. Camera need s
to be pr essed into the
Camera mou
nt
c omple tely; o th erwise,
thec mter ofgr<Mty..; 11
be incc nec t
Th e gi mb al do es Gimba1 may hav e Cycle th egi rrba l
not functi on or been mov ed durin g power on/ off by
r esp ond
initialization switching model
on/o ff.
14
Yuneec Exhibit 1037 Page 14

G imbal will not Gmba 1control If using GB200'"w it h
pow er on. harness may no t be
Bl ad e• 350 OX2, be su re
con nec ted into t he to connec t th e control
correct port harness to t he earnera
!'.itch con tr ol port .If
us in g with any other
model, be sure to
connect PWM i npu t
to po rt the unive rsa l
PWM in put por t and
mode con t ro l port
G imbal does not Gmba 1may not have Gieck gimbal control
respond
to cont rol posit iv e co nnection harness/s atellite r
inputs and
LEDs via con tr ol harness or ece ive r for a solid
are gl ow ing so !i d sa t el lit e receiver. connec ti on. Try
RED and B LUE. disconnecting and
reconnect
in g t he
cont rol ha-ness/sat el lit e
receVff zndcycling!he
pow er on/o ff.
Red L ED on gi mba l T he gyro board Check t he connection
fl ashes slowly and harness may have betwe en the gyro
gi mba li s di scon nected from boa rd and the GB 2 00' "
inoperable . t he GB200 '~ c on tr o l cont ro l board.
board .
15
Yuneec Exhibit 1037 Page 15

LIMITED WARRANTY
YUNEE('•warrants that for a period of (90) days from original date
ofpurchase, the pro du ct wil Ibefree from defects in materials and
workmanship under normal use.
In the event of a defect please
contactYUNEEC customer Support(www.Yuneeccom)for assist-
ance.
YUNEEC's sole obligation under this warranty will be, at its
option, to repair or replace the product This warrantydoes not
apply to products damaged by misuse, accident or normal wear
and tear andwaterdamage.
All implied warranties of merchant-
ability or fitness for aparticular purpose are limited tothe duration
ofthis warranty. YUNEEC'" disdaims all other expressed or implied
warranties or conditions. to the extent
not prohibited by law, in
no event will YUNEEC'" beI iable for any loss ofrevenue or profit or
for any special, indirect, consequential, incidental or punitive
damages, howevercaused, arising out of or related to the use of
or inability to use the product,even ifYUNEEC'"has been advised
ofthe possibility ofsuch damages. In no event will Yu neec'" liability
exceed the amount paid by you for the product Some jurisdictions
do not a
ll ow limitations on howlong an impli ed wa rr anty lasts,
or the exdu sio nor limi ta ti on of ind de ntal or co nsequential da ma-
ges,
so the above limitations or ex clu sions may not a ppl y toyo u.
Thi swa rr antygivesy ou spe cifi clegal ri gh ts, andyou m ay alsohave
other
ri ghts,which vary by juris di ction.
BLRIJE.
C opyr ight 2014 YLl'lee<Inte rn ational Co , lt d. I Hori zo n Ho bb y, LLC
16
Yuneec Exhibit 1037 Page 16