Nauticam NA-SHINOBI-H User manual

NA - SHINOBI-H /
NA - SINOBI-S
For Atomos Shinobi 5.2” 4K HDMI Monitor with HDMI 1.4 Input / SDI Input
PN 17923 / 17924
Introduction 2
2
3
4
7
8
Package Contents
Important Instructions
Part Names and Functions
Opening the Housing
Closing the Housing
9
16
11
18
Setup Options
Preparation for Use
Cable Connection
Pre-installed M16 Vacuum Valve II
19
20
21
22
Care/Storage
Warranty
Specications
HDMI Cable Compatibility
User Manual
Housing
Monitor

2
INTRODUCTION
PACKAGE CONTENTS
Thank you for purchasing this Nauticam product.
Before using the product, please read this manual thoroughly to familiarize yourself with full scope of functions on the
product as well as ensuring that you will use the product correctly.
Make sure that you have all the included items listed below before using this product.
If some items are missing or damaged, contact your local Nauticam dealer.
NA - SHINOBI-H (HDMI) NA - SHINOBI-S (SDI)
Pre-installed items :
- HDMI Cable ( A-D ) 0.75m length
- M25-M16 Step Down Adaptor
- 25625 M16 Vacuum Valve II
- NAV0014 Mounting Ball with screws
Pre-installed items :
- SDI Cable 0.75m length
- M25-M16 Step Down Adaptor
- 25625 M16 Vacuum Valve II
- NAV0014 Mounting Ball with screws
Standard HDMI bulkhead
with M16 thread
M16 SDI Bulkhead
M16 Extension Ring SDI Cable from
Camera to SDI
Bulkhead
0.40m length
HDMI Cable from Camera
to HDMI Bulkhead :
HDMI (D-D) Cable
200mm length
HDMI (D-C) Cable
190mm length
1
1
2
2
Monitor Hood
Lubricant
Hand Pump
Panasonic CR2032 Battery
(pre-installed for Moisture Alarm)
Spare O-ring
Manual Instruction Card Padded Travel Case
O-ring Remover
After purchase, we suggest that you reuse all packaging materials for future travelling.

3
IMPORTANT INSTRUCTIONS
Water-tight test of the housing (without
monitor inside) before usage is recom-
mended as well as any O-ring renewal
and port change.
Use only Nauticam lubricant on silicone
rubber O-ring.
Discontinue use immediately when there is
a sign of leakage.
Do not expose the housing in direct
sunlight for a prolonged period.
Prevent any sand or dust or water pen-
etration inside the housing. Be extra
careful when inserting or removing the
monitor.
This product is not intended for use by
children, or persons with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
are supervised and/or given instruction by
a responsible person concerning use of
the product to ensure that they can use it
safely.
Do not seal the housing when travelling by
air as this may lead to a pressure difference
between the atmosphere and inside the
housing.
Only the accesories specied by
Nauticam must be used. Third-party
accessories may result in malfunctions
or damage to the product.
Do not stretch any O-rings excessively.
Only remove it using Nauticam O-ring
remover.
Do not open the housing in wet or sandy
environment. Protect the housing from
moisture and debris in order to prevent
malfunction or leakage.
1
3
5
7
9
11 12
4
6
8
10
2
Do not attempt to remove parts of the
housing yourself. Repairs must be done
at authorized service centers only.
The housing should be positioned on the a
stable and safe surface on land.

4
PART NAMES AND FUNCTIONS
RGB Overlay button Luma Waveform button
Monitor button Close button
Vectorscope zoom button RGB Histogram button
Settings lever
Vectorscope button
Analysis button
RGB Parade button
Histogram button
1 2
3 4
5
7
9
11
6
8
10
Rear View
1
3
6
8
4
5
2
7
10 119

5
PART NAMES AND FUNCTIONS
Power button
NAV0014 Mounting ball
with screws
M25 Accessory port HDMI / SDI cable
Zinc Anodes1
5
2
3 4
Front + Bottom Views
3
24
5
1

6
PART NAMES AND FUNCTIONS
Top + Side Views
Housing unlock button
M16 Accessory port Moisture alarm window
3
1 2
2
1
3

7
OPENING THE HOUSING
1
2
3
depress housing unlock button
turn housing lock latch
anti-clockwise to open the
housing
ip open the back housing
when lock latch is aligned to
‘open’ position
* drawings as illustrations only

8
CLOSING THE HOUSING
1
2
3
before closing the housing, clean
and lubricate the main O-ring
make sure nothing is caught
between front and back housing
and that they are fully aligned
before locking
main O-ring
insert the housing shaft into the
shaft hole and then rotate the lock
latch clockwise until you hear and
feel it click into place
housing locked in place securely
* drawings as illustrations only

9
SETUP OPTIONS - HDMI
HDMI IN
HDMI IN + SDI OUT
25065
SDI Surface Cable
in 45.0m length
M25-M16
Step Down Adapter
17923
NA - Shinobi-H Housing
for Atomos Shinobi 5.2”
4K HDMI Monitor with
HDMI 1.4 input
25081
M24 - M16 Step Down
Adapter is needed when
accessory port of the
housing is M24
25060
SDI Cable in 0.40m length
25036
HDMI (D-C) Cable in
190mm length
25071
HDMI 1.4 (A-D) Cable in
0.75m length
25033
Standard HDMI Bulkhead
with M16 thread
25046
HDMI (D-D) Cable in
200mm length
* drawings as illustrations only
included in package
not included in package
25058
M16 SDI Bulkhead

10
SETUP OPTIONS - SDI
* drawings as illustrations only
SDI IN
SDI IN + SDI OUT
25065
SDI Surface Cable
in 45.0m length
25058
M16 SDI Bulkhead
25060
SDI Cable in 0.40m length
17924
NA - Shinobi-S Housing
for Atomos Shinobi 5.2”
4K HDMI Monitor with
SDI input
M25-M16
Step Down Adapter 25096
SDI Cable in 0.75m length
M16 SDI Bulkhead
25060
SDI Cable in 0.40m length
included in package
not included in package