NCast PR-MINI User manual

NCast Presentation Recorder
PR-MINI
Streamer-Recorder
www.ncast.com
408.844.9080

Installation
There are a few easy steps to get your PR-MINI Recorder and
Streamer up and running:
Unpack the unit and plug in the Micro-US power supply, your
ethernet cable (if you will be using a wired connection) and an
HDMI monitor (if you have one). Power on the unit. Make note of
the Serial Number (needed for wireless access and administrative
access).
Initial configuration can be done via wireless. Look for a wireless
network with an SSID similar to AP-xxxxxxxxxxxx and use the
serial number of your unit as the password to sign in.
Alternatively, plug the unit into an ethernet network with DHCP
and check the attached HDMI monitor for the registered IP
address. Enter "192.168.42.1" if on wireless or the IP address if
wired and login using "admin" as the user and the "serial number"
as the password.
Proceed to the "Configuration" tab and click on the Network icon.
Configure your wireless or wired network as needed.
Go to the Quick Start page and press Start to start recording and
then Stop when you have finished.
Visit the Archives page and download your recording. You're
done!
Reboot the unit (icon in the upper right corner) and login with the
new network address.

Configuring From a oot File
The following file may be used to configure the wired and wireless
addresses of the recorder. Create a file called “network.txt” and
place on a US stick during the boot process.
dhcp=true
dns_1=8.8.8.8
dns_2=8.8.4.4
gateway=192.168.10.1
ipaddress=192.168.10.24
netmask=255.255.255.0
ap=true
## 2- 2 characters
ap_ssid=PR-ACCESS
## 8-64 characters
ap_password=passphrase
## 2- 2 characters
wifi_ssid=MyWiFi
## 8-64 characters
wifi_password=passphrase
wifi_1_ssid=MyWiFi-1
wifi_1_password=passphrase1
Only lines needed for configuration are necessary. For example,
to configure a static IP address:
dhcp=false
dns_1=8.8.8.8
dns_2=8.8.4.4
gateway=192.168.10.1
ipaddress=192.168.10.24
netmask=255.255.255.0
To configure WiFi only:
ap=false
wifi_ssid=My-WiFi-Network
wifi_password=passphrase

Warranty Information
Thank you for your purchase of NCast Corporation products. We strive to provide you with the best
quality and service possible. Our standard LIMITED WARRANTY terms and conditions are stated
below:
NCast Corporation warrants that its products will be free from defects in material and workmanship
for one year if used and maintained properly. The warranty time limit begins on the date of the
invoice or packing slip of the product (whichever date is later) and applies only to the original
purchaser. Additional years of warranty may be purchased. Please contact NCast sales.
NCast Corporation will accept returns of product within 45 days of the product ship date if
accompanied by a valid Invoice number for a refund of the purchase price. The customer is
responsible for the cost of return shipping and is responsible for any loss or damage to the product
during shipping. The warranty is voided for any product that is returned damaged, regardless of
whether the damage was caused by the shipping carrier or by the customer.
Please contact us for refunds or exchanges within forty-five (45) days of shipment. After forty-five
(45) days, refunds and exchanges are no longer available for any reason.
This warranty is invalid if the serial number has been altered or removed from the product or if
altered, repaired or serviced by anyone other than our service department.
After forty-five (45) days, only a manufacturing defect will qualify for a warranty exchange or repair.
If we are unable to repair the product, we will replace the unit with a comparable product that is
either new or refurbished. No warranty will apply after the limited warranty period has expired.
Software for recorder/streamer and server products is maintained at no charge. This applies to bug
fixes and minor revision feature upgrades. The customer is responsible for performing updates.
Major revision upgrades may require additional fees. Support services for server software updates
may be purchased as required.
The customer is responsible for any Duty, VAT or other non-shipping charges or taxes incurred in
the destination country. International duties and taxes are never included in the invoice for an order.
If the customer refuses delivery of an international order, the customer will be responsible for any
fees associated with an order return to the company, and could be responsible for the duties and
taxes even if the order is returned.
Products should be returned in the original packaging if possible. Any damage incurred is the
responsibility of the customer.
When returning a product please include the original Invoice Number and reasons for the return.
All shipments or other correspondence with the company may be sent to the following address:
NCast Corporation Serial Number:
4677 Old Ironsides Drive, Ste 430
Santa Clara, CA 95054-1826
Main Phone: [phone]
Fax: [phone]-06-12
Email: [email protected] Copyright © 2016 - NCast Corporation. All Rights Reserved.