NCR 7403-K112 Manual

7403‐K112
WirelessUSBExtensionCable
KitInstructions

IssueC

Revision Record
Issue Date Remarks
AMar2009Firstissue
BMar2010NewWirelessdevice
CJune2011Added7610/7611Support

1
Introduction
ThiskitprovidesaUSBExtensionCableandVelcrostripsthatareusedtointegratea
WirelessUSBClientintheRealPOS70xrt(7403),RealPOS25(7610),and
RealPOS50(7611)terminals.
Reclosable Loop Fastener
497-0459601
USB Extension Cable
497-0464532
Reclosable Hook Fastener
497-0459602
FCC Label
497-0462138


2
TherearetwoversionsoftheWirelessUSBClient:
2330‐K370(U.S.Only)
2330‐K371(International)
TheWirelessUSBClientkitcontainsthefollowing:
USBClient
USBClientStandwithCable1.5mCable(notusedinanintegratedconfiguration)
CD‐ROMcontainingsoftwaredriveranddocumentation
ORiNOCO®802.11a/b/g/n
USBAdapterwithCap

USBCradle

CDcontainingsoftware,
driversanddocumentation

PrintedQuickInstallGuide


3
Installation Procedures (7403)
ThewirelessdeviceconnectstoadedicatedUSBportinthe7403displayhead.
1. Loosenthecaptivescrews(2)thatsecuretheTopAccessCover.
2. RemovethecoverfromtheRearCabinet.
27308
Top Access Cover

3. InstalltheHookandLoopFasteners(Velcro).
a. AdheretheHookFastenertothebacksideoftheWirelessClient.
Velcro Hook Fastener


4
b. AdheretheLoopFastenertotheRearCabinet.
c. AdheretheFCCLabeltotheRearCabinet.
27312
Velcro Loop Fastener FCC Label

4. ConnecttheWirelessUSBExtensionCabletotheWirelessClient.
Note: TheUSBClientStandw/1.5mCableisnotusedandcanbediscarded.
Wireless USB Extender Cable
Wireless Client


5
5. FastentheWirelessClienttotheRearCabinetusingtheVelcrostrips.
6. ConnecttheWirelessUSBExtensionCabletothe7403USBport.
7403 USB Port

7. ReplacetheTopAccessCover.

6
Installation Procedures (7610/7611)
ThewirelessdeviceconnectstoadedicatedUSBportontheterminal.
1. OpentheTerminalCableCover.PresstheCableCoverTabs(2)andpivotthe
coveropen.
29242
Cable Cover Tabs


7
2. AdheretheVelcroLoopFastenertotheTerminalCableCoverasshown.
2
9806
Velcro Loop Fastener

3. AdheretheFCCLabelontheTerminalBackCoverasshown.
2
9
2
38
Certification Label
Certificate of Authenticity Label
(Large) Certificate of Authenticity Label
(Small)
FCC Label


8
4. AdheretheVelcroHookFastenertothebacksideoftheWirelessClient.
Velcro Hook Fastener

5. ConnecttheWirelessUSBExtensionCabletotheWirelessClient.
Note: TheUSBClientStandw/1.5mCableisnotusedandcanbediscarded.
Wireless USB Extender Cable
Wireless Client

6. FastentheWirelessClienttotheTerminalCableCoverusingtheVelcrostrips.
2
980
7


9
7. ConnecttheWirelessUSBExtensionCabletotheterminalUSBport.
29808
USB Ports

8. ClosetheTerminalCableCover.


10
Installing the Software
SeetheQuickStartUser’sGuideontheCD‐ROMtocompletetheWirelessClient
installation.
Error Message
SomeNCRGoldImageshaveaservicedisabledthatisrequiredtoruntheWireless
Client.Ifyougetthefollowingmessagewhentryingtoconfigurethenetwork
connectionyouneedtostarttheWirelessZeroConfigurationservice.

Toenabletheservice:
1. SelectStartControl PanelAdministrative ToolsServices.

11
2. Scrolldownanddouble‐clickonWirelessZeroConfigurationtoopenupthe
Propertieswindow.

3. SettheStart‐upTypeoptiontostarttheserviceAutomatically.

