NCR 7610-K41 User manual

7610‐K41
I/OExpansion
KitInstructions

IssueA

Revision Record
Issue Date Remarks
AFeb2011Firstissue
 
 

1
Introduction
ThiskitprovidesoneRS‐232connectorw/harnessandonePS/2connectorw/harness
forthe7610/7611ConnectorPanel.
Note: TheRS‐232cablecannotbeinstalledifanIntegrated2x20CustomerDisplayis
present.BothdevicesusetheinternalRS232/Dheader.
2
9
4
08
PS/2 Gasket
497-0470544
PS/2 Panel Mount Cable
497-0466593
Screw, Standoff, 4-4- x 0.187 x 0.462, Hex
006-8613209 RS-232 Panel Mount Cable
497-0468839

Installation Procedures
Warning: DisconnectthepowerbeforedisassemblingtheTerminal.
1. DisconnectthePowerCable.
ThePowerCableconnectorlocksintopositionwhenconnectedtotheterminaland
cannotberemovedbysimplypullingonthecable.Youmustgrasptheconnector
andslidetheoutsidehousingoutfromtheterminaltounlockitfromtheterminal
connectortoremoveit.
29249a
Terminal Power Cable


2
2. RemovetheTableTopStand.
a. Laytheterminalfacedownonaflatsurface.
Caution: Thefrontbezelisapaintedcomponentandtheweightofthe
terminalcancauseabrasionswhenmovedaroundonasurface.Alwaysusea
softmaterial(cloth,foam)toprotectthebezelwhenplacingtheterminalface
down.
b. Loosenthecaptivethumbscrews(2)thatsecuretheTableTopStand.
2
9
241
a
Protective Foam or Cloth

c. SlidetheTableTopStandasshowntodisengagetheslotsintheTableTop
StandfromtheMountingStudsonthebackoftheterminal.
2
9
2
39a
Mounting
Slots
Mounting
Studs


3
3. RemovetheRearCover(loosenthecaptivescrews(4)thatsecureittothechassis.)
29287
Captive Screws

Installing the RS-232 Port
4. RemovetheRS232/DknockoutfromtheConnectorPanel.Insertaflatscrewdriver
intheslotandtwisttheknockoutupanddowntobreakitloose.
2
9
4
09
RS-232/D Knockout


4
5. InstalltheRS‐232ConnectorontheConnectorPanel(2hexscrews).
2
9
41
8

6. ConnecttheRS‐232CabletoCOMDontheMotherboard.
2
9
41
9
COMD


5
7. SettheCOMDjumperto12Vpowered.
2
9
42
0
COMD
* Default setting
Ring Indicator
12 V
5 V


6
Installing the PS/2 Port
8. RemovethePS/2knockoutfromtheConnectorPanel.Insertaflatscrewdriverin
theslotandtwisttheknockoutupanddowntobreakitloose.
2
9
412
PS/2 Knockout

9. RemovethehexnutfromthePS/2Connector.
2
9
41
3


7
10. RoutethePS/2CablethroughtheConnectorPanelfromtheoutsideofthe
terminal.InsertPS/2Gasketandhexnutontothecable.Notetheorientationofthe
extensionsonthegasket(awayfromtheconnector).
29415
Hex Nut
PS/2 Gasket

11. AlignthePS/2ConnectorandGasketproperlywiththekeyedholeinthe
ConnectorPanelandthensecuretheconnectorwiththehexnut.
2
9
41
6


8
12. ConnectthePS/2CabletothePS/2ConnectorontheMotherboard.
29417
PS/2 Connector

13. ReplacetheRearCover(4captivescrews).
2
9
2
9
2

14. ReplacetheDisplayHeadontheTableTopStand..

