NCR 7452 User manual

NCR 7452 Workstation
Release 3.1
Hardware User’s Guide
BD20-1373-C
Issue J

The product described in this book is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,
and firmware become available. NCR, therefore, reserves the right to change specifications without prior
notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,
consult with your NCR representative or NCR office for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization,
and value of this book.
Address correspondence to:
Manager, Information Products
NCR Corporation
2651 Satellite Blvd.
Duluth, GA 30096
Copyright © 2001
By NCR Corporation
Dayton, Ohio U.S.A.
All Rights Reserved

i
Preface
Audience
This book is written for hardware installer/service personnel, system
integrators, and field engineers.
Notice: This document is NCR proprietary information and is not to
be disclosed or reproduced without consent.
Safety Warnings
Fuse Replacement
Caution: For continued protection against risk of fire, replace only
with the same type and ratings of fuse.
Attention: Pour prévenir et vous protéger contre un risque de feu,
remplacer la fusible avec une autre fusible de même type, seulement.
Power Supply Cord Used as Disconnect Means
Caution: The power supply cord is used as the main disconnect
device. Ensure that the socket outlet is located/installed near the
equipment and is easily accessible.
Attention: Le cordon d'alimentation est utilisé comme interrupteur
général. La prise de courant doit être située ou installée å proximité du
matériel et être facile d'accés.
Warning: DO NOT connect or disconnect a printer, keyboard, or
any other terminal-powered peripheral while the terminal is
powered on. Doing so may result in peripheral or system damage.
Lithium BatteryWarning
Caution: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type as recommended by the
manufacturer. Discard used batteries according to the manufacturer's
instructions.

ii
Attention: Il y a danger d’explosion s’il y a remplacement incorrect de
la batterie. Remplacer uniquement avec une batterie du même type ou
d'un type recommandépar le constructeur. Mettre au rébut les batteries
usagées conformément aux instructions du fabricant.
Peripheral Usage
The workstation should only be used with peripheral devices which
are certified by the appropriate safety agency for the country of
installation (UL, CSA, TUV, VDE) or those which are recommended by
NCR Corporation.
Environmental Consciousness
NCR's concern for the environment is demonstrated by the intelligent
power management system of the workstation that operates efficiently
in a standalone or network environment.

iii
References •NCR 7452 Workstation Hardware Service Guide (B005-0000-1344)
•NCR 7452 Workstation Site Preparation (BD20-1378-C)
•NCR 7452/7453 Workstation System Cables (BD20-1376-C)
•NCR 7452 Workstation Parts Identification Manual (BUF0-0630)
•NCR 74xx Workstation Software User’s Guide (BD20-1374-C)
•NCR 74xx Workstation Interpreting Error Logs User’s Guide
(BD20-1442-B)
•NCR 74xx Workstation TAPS Diagnostics User's Guide (BD20-1441-B)
•NCR Retail TAPS Programming Help File (BD90-0261-C)
•NCR 5932 Wedge Keyboard User Guide (BD20-1369-A)
•NCR 5952 Wedge DynaKey User Guide (BD20-1370-A)
•NCR 5962 Wedge Touch Screen Module User Guide (BD20-1371-B)
•NCR 5963 Wedge Touch Screen User Guide (B005-0000-1131)
•NCR 5972 Wedge 2x20 Customer Display User Guide (BD20-1372-A)
•NCR 5942 10.4-Inch LCD Consumer Information Display User Guide
(B005-0000-1080)
•NCR Wedge Software User Guide (BD20-1368-B)
•SMC EtherEZ ISA Ethernet Adapters User Guide (79-000630-000)
•NCR 5973 International VFD Customer Display (B005-0000-1162)
•NCR 5953 12.1 Inch DynaKey User Guide (B005-0000-1161)

iv

v
Table of Contents
Chapter 1: Product Overview
Introduction ..................................................................1-1
Workstation Configurations ........................................1-3
Integrated 7452 .......................................................1-3
Semi-Modular 7452 ................................................1-5
Modular 7452..........................................................1-6
Hardware Modules.......................................................1-7
Processor Board......................................................1-7
Graphics (other than Series 4000)....................1-10
Graphics (Series 4000)......................................1-11
Power Management.........................................1-12
NCR 5952 Wedge DynaKey Module.........................1-13
NCR 5953 12.1" DynaKey...........................................1-14
NCR 5962 Wedge Touch Screen................................1-16
NCR 5963 Wedge Touch Screen................................1-17
NCR 5932 Wedge Keyboard......................................1-18
Features.................................................................1-19
115-key Big-Ticket Keyboard...............................1-19
68-key POS Keyboards (Regular and Low Cost)1-19
Keylock..................................................................1-20
Speaker..................................................................1-20
System Status Indicator LED...............................1-21
MSR .......................................................................1-21
External Decoded Scanner Connector ................1-22
Special PC Setup Keypad Layout for POS
Keyboard...............................................................1-22
NCR 5972 2x20 Customer Display ............................1-23
Features.................................................................1-23
NCR 5973 International VFD Customer Display .....1-27

vi
Features.................................................................1-27
NCR 5942 10.4" Customer Display............................1-30
Features.................................................................1-30
Printer Options ...........................................................1-31
2208 Printer...........................................................1-31
7141 Printer...........................................................1-32
7152 Printer...........................................................1-32
7156 Printer...........................................................1-33
7158 Printer...........................................................1-33
7162 Printer...........................................................1-34
7193 Printer...........................................................1-34
7194 Printer...........................................................1-35
System Configuration Diagram.................................1-36
Chapter 2: Workstation Hardware Installation
Installation Restrictions................................................2-1
AC Input Selection Switch.................................2-2
Out-of-Box Hardware Installation...............................2-3
Integrated Workstation..........................................2-3
Cash Drawer Installation...................................2-7
Hand-Held Scanner Installation......................2-12
Cable Routing From the Workstation.............2-13
Semi-Modular Workstation.................................2-14
Modular Workstation...........................................2-16
5952 DynaKey Workstation Configuration........2-17
5953 DynaKey Workstation Configuration........2-20
5962 Touch Screen Workstation Configuration .2-23
Chapter 3: Installing Optional Hardware Features
Introduction ..................................................................3-1
Installation Restrictions..........................................3-1

vii
Cautions ..................................................................3-1
Installing a 5952 DynaKey ...........................................3-2
Installing an Integrated 5952 DynaKey ................3-3
Installing a Checkstand-Mounted 5952
DynaKey..................................................................3-7
Installing a Remote 5952 DynaKey .....................3-12
Wall-Mounting the 5952 DynaKey......................3-15
Installing a 5953 DynaKey .........................................3-17
Installing a Table-Top Mounted 5953 DynaKey 3-19
Adding a 2x20 Customer Display...................3-20
Installing a Wall Mounted 5953 DynaKey..........3-22
Installing a Checkstand-Mounted 5953
DynaKey................................................................3-23
Installing a Weighted Base Checkstand .........3-23
Installing a Checkstand Base...........................3-24
Connecting the 5953 DynaKey (2xxx, 3xxx).......3-27
Installing a PCI LCD Board.............................3-27
Connecting a 5953 DynaKey without Touch
Screen ................................................................3-30
Connecting a 5953 DynaKey with Touch
Screen ................................................................3-30
Connecting the 5953 DynaKey (4xxx).................3-31
Installing a 5962 Touch Screen Module ....................3-33
Installing a Remote 5962 Touch Screen Module 3-34
Wall-Mounting a 5962 Touch Screen Module....3-39
Installing an Integrated 5962 Touch Screen
Module..................................................................3-41
Installing an NCR 5963 Touch Screen Module.........3-44
Installing the PCI LCD Board..............................3-44
Equipment ........................................................3-45
Tools Needed....................................................3-45
Connector/Strapping Identification...............3-46

viii
Cables................................................................3-47
Installation in Terminal....................................3-48
Connection to 5963 LCD Touch Screen
Display and Keyboard.....................................3-51
Wall-Mounting a 5963 Touch Screen Module....3-52
Installing a 2x20 Customer Display...........................3-53
Installing a High-Post Table-Top Mounted 2x20
Customer Display.................................................3-55
Installing an Integrated 2x20 Customer Display3-58
Installing an International VFD Customer Display .3-61
Installing a Table Top Mount International
Customer Display.................................................3-61
Installing a 16" High Post Mount International
Customer Display.................................................3-62
Installing an Integrated Mount International
Customer Display.................................................3-64
Installing a Remote CRT Customer Display.............3-67
Installing a 5942 10.4" LCD Consumer Information
Display.........................................................................3-69
Installing a Win95 Intel EtherExpress Pro Adapter
Driver...........................................................................3-70
Installing a Win2000 AMD Ethernet Driver .............3-72
Installing an External CD-ROM Drive......................3-74
Installing the Hardware.......................................3-75
Installing the Drivers............................................3-76
Installing Additional Ports.........................................3-78
Installing Parallel Port / RS-232 Port Kit (4xxx) 3-78
Installing a Four-Port PCI RS-232 Board ............3-79
Hardware Installation......................................3-79
Software Installation ........................................3-79
Default I/O Address and Interrupt Settings
for Win95/NT...................................................3-82