NCR 5968-K154 Manual

Kit Instructions
Capacitive Biometric Reader
5968-K154
Issue A

The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR RealPOS is a trademark of NCR Corporation in
the United States and/or other countries. Other product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book. Please use the link below to send your comments.
Email: [e-mail]
Copyright © 2019
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved
Revision Record
Issue Date Remarks
AJan 2019 First Issue

Capacitive Biometric Reader
This kit provides a Capacitive Biometric Reader for the 15" or 18.5" 5968 RealPOSX-
Series Display.
Kit Contents

2 Capacitive Biometric Reader
Installation Procedure
1. Remove the screws (2) that secure the Stand and Rear Cover to the display.
Caution: Always use a soft material (cloth, foam) to protect the display screen when
placing the terminal face down.
2. Pivot the Stand and Rear Cover assembly as shown to remove it.

Capacitive Biometric Reader 3
3. Remove the Display Collar (7 screws).
4. Remove the Blank Plate from Port A of the Display Collar. The plate is connected to
the Display Collar with a strong adhesive. Use care when removing it to avoid
damage to the Display Collar.

4 Capacitive Biometric Reader
5. Mount the Capacitive Biometric Reader on the Display Collar.
a. Route the Capacitive Biometric Reader Cable through the cable access of the
Display Collar.
b. Install the Capacitive Biometric Reader on the Display Collar (2 screws included
in the kit).
Note: Do not overtighten the screws.
6. Route the Capacitive Biometric ReaderCable through the Cable Guide on the Display
Collar.

Capacitive Biometric Reader 5
7. Install the Display Collar on the terminal (7 screws).
8. Connect the Capacitive Biometric Reader Cable to the Motherboard.
9. Tape the Capacitive Biometric Reader Cable to the Display Sled between the score
lines as shown below. This locates the cable so it does not get pinched when the Rear
Cover is installed.
10. Reinstall the Rear Cover and Stand.

6 Capacitive Biometric Reader
Cleaning and Using the Biometrics Reader
Sensor Cleaning Procedures
Daily Cleaning
Before each authentication, it is recommended that the user first clean the sensor. Place
adhesive tape onto the sensor and then pull it off. This assures that residue from
previous usage is removed.
Caution: Do not use abrasive materials to clean the sensor, including paper products.
Only adhesive tape should be used.
Using the Biometrics Reader
Place thumb/finger flat and straight on the sensor. If this is not possible, try to place
thumb/finger on the sensor in the same angle every time.
Under normal usage conditions dirt, residue, oils, and other materials can collect on
users’ fingers. This can possibly cause poor collection of fingerprint data, which can
cause performance degradation. For the best results, it is recommended that the user
keeps their fingers relatively clean and free of residues that may alter the sensor
performance.
Scotch tape can be used to clean fingers. Adhere the tape to the finger and then pull it
off.

Capacitive Biometric Reader 7
Software Drivers
The RealPOSCapacitive Biometrics Reader is a TouchChip TCET Silicon Module
utilizing sensor TCETD1FG022. Please visit the Crossmatch website for drivers and
application developer tools.
https://www.crossmatch.com/company/support/request/

8