Neo Instruments Mini Vent User manual

USER MANUAL V1.0
12V DC
Connect the included AC adapter (12V DC, 0.5A) only. Always connect all other cords before plu in
in the AC adapter. The Mini Vent can not be powered by batteries.
IN
This jack accepts mono or an and keyboard si nals.
OUT L , OUT R / MONO
The mini Vent provides a stereo output. If you just need a mono si nal the R / MONO output delivers
the best quality, particularly in STOP mode.
A-B
Switches between two pro rammable settin s of the mini Vent. See > Pro rammin .
BYPASS
Turns the rotary effect on and off. When the red LED li hts up, the effect is active, when it’s off the
si nal is relayed to both outputs via a true bypass circuit.
SLOW / FAST
Switches the rotors to slow or fast speed. The yellow Lo and red Hi Leds indicate the current speed of
the virtual rotors.
STOP
Pressin both the Bypass and Slow / Fast switch simultaneously causes the rotors to stop.
The rotors always stop in the front position.
Input Gain Se ect
The mini Vent for Or an is set to Lo Gain input from the factory. If your or an’s output is too low to
et enou h DRIVE, the mini Vent can be switched to Hi Gain.
1. Unplu the AC adapter of the mini Vent
2. Unscrew the 4 screws on the bottom and open the enclosure
3. Find the jumper soldered flat on the PCB board (see picture below)
4. Remove the jumper and attach to both pins
5. Attach the bottom cover with the 4 screws

Programming
The followin parameters can be edited and stored to switch settin A or B:
- Drive Intensity
in 5 steps (off,1,2,3,full)
- Distance
in 5 steps
Settin s are stored to flash memory so that there's no repro rammin necessary on power up.
1. Power up the mini Vent while holdin the Slow/Fast switch for 3 seconds
This enters the edit routine, effect will be switched on and Slow Speed is selected
2. Set the A-B switch on the back accordin to the memory settin you want to edit
3. The Speed LEDs reflect the parameter settin s. Lo LED represents "Drive", Hi LED represents
"Distance". The parameter value is indicated throu h flashin or constant lowin .
Here's a list of all possible settin s:
Drive off (Lo LED blinks 1x/sec)
Drive 1 (Lo LED blinks 2x/sec)
Drive 2 (Lo LED blinks 3x/sec) factory default for A
Drive 3 (Lo LED blinks 4x/sec)
Drive full (Lo LED constantly on) factory default for B
Distance 1 (Hi LED blinks 1x/sec)
Distance 2 (Hi LED blinks 2x/sec)
Distance 3 (Hi LED blinks 3x/sec) factory default for B
Distance 4 (Hi LED blinks 4x/sec) factory default for A
Distance 5 (Hi LED constantly on)
4. To increase the Drive value, press the Bypass switch repeatedly, to increase the Distance value
press the Slow / Fast switch repeatedly. Once you reached the hi hest value, the next button press
will take you to the first value a ain.
5. To le the A-B switch if the other memory shall be edited too and repeat the previous steps
6. When editin is finished press Bypass and Slow/Fast simultaneously and hold for 2 seconds.
Settin s will be stored and the mini Vent returns to play mode (effect on, slow speed).
Warranty terms
Neo Instruments extends a warranty coverin all verifiable defects in material and workmanship for a
period of 12 months from the date of ori inal purchase. Statutory warranty ri hts remain unaffected
hereby. The warranty covers the remedyin of manifest defects by replacin or repairin defective
parts. Any other claims, in particular those for a reduction in price or cancellation of contract, may
only be made after an attempt to rectify the defect or deliver a replacement has failed.
The warranty does not cover dama e incurred durin transit, as well as dama e caused by non-
compliance with the operatin manual and improper or ne li ent handlin of the device. Beyond that,
the warranty does not cover defects or dama e caused by acts of God (includin but not limited to
li htnin , floods, etc.) or other external influences, as well as mechanical dama e or flaws that are
not attributable to manufacturin defects. If defects occur durin the warranty period, please contact
us at the followin address:
NEO Instruments
Flemin strasse 20-22
D-36041 Fulda
[phone]
[e-mail]
www.neo-instruments.de
© 2013 Neo Instruments All Ri hts Reserved