NeoTech JPEG2000 Installation and operating manual

Best picture quality DVR
JPEG2000 Stand-alone DVR
0
INSTALLATION & SAFEGUARDS
All the safety and operating instructions should be read before the unit is operated.
Environment Condition for Installation
- To prevent electric shock or other hazard, do not expose units to rain, moisture, or dust.
- This unit should be located in an area with low humidity and a minimum of dust..
- Place this unit in a well-ventilated place and do not place heat-generating objects on this unit.
- This unit should not be located in an area where it is likely to be subjected to mechanical shocks.
Before You Start
- Ensure the power switch is in the OFF position prior to starting.
- Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.
- Installation should be performed by qualified service personnel only.
- This unit should be operated only from the type of power source indicated on the manufacturer’s
label and with the power supply included with the unit.
Notice
- Before initial configuration or operation you must first set the TIME/DATE, followed by
setting the unit to the FACTORY DEFAULT settings, lastly clearing the HDD. Please follow
these steps in order.
- Before installing a second HDD, ensure that the drive conforms to the specifications
listed on the specifications page at the end of this manual. When installing a second HDD,
set the drive to SLAVE. After installation, first reset the TIME/DATE, followed by resetting
the unit to the FACTORY DEFAULT settings, lastly clearing the new HDD.
- Pull the unit out of record mode prior to cutting power to the unit. Do this by entering the
setup menu, followed by switching the unit off. Powering off the unit while writing to the
disks can cause critical malfunctions. (ex: Recording Error, Playback Error, System Error)
- When you set the record type, you have to set the Record Configuration and also
Schedule Setup. This unit records as per the Record type & Schedule setup.
- The [REC] button on the front panel is for emergency record using highest image quality.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the
user of this equipment that there are dangerous voltages within the enclosure which may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to presence of
important operating and maintenance(Servicing) instructions in the literature accompanying the
appliance.
Installation & Safeguards
Ver 1.3

Best picture quality DVR
JPEG2000 Stand-alone DVR
1
Contents
Contents
16----------------------------------------------------------------Playback4-7.
16----------------------------------------------------------------Record4-6.
15----------------------------------------------------------------Zoom View5)
15----------------------------------------------------------------Freeze View4)
14----------------------------------------------------------------Display Configuration4-4.
14----------------------------------------------------------------Factory Default4-3.
13----------------------------------------------------------------System Log-in4-2.
13----------------------------------------------------------------Start-up DVR4-1.
15----------------------------------------------------------------PIP View3)
15----------------------------------------------------------------Sequencing Cameras2)
15----------------------------------------------------------------Full / Multiple View1)
15----------------------------------------------------------------Live View Setup4-5.
17
18
18
----------------------------------------------------------------
----------------------------------------------------------------
----------------------------------------------------------------
Search
PTZ Camera Operation
Data Back-Up
4-8.
4-9.
4-10.
13----------------------------------------------------------------OperationCHAP. 4
12----------------------------------------------------------------RS-232C ASCII-code8)
12----------------------------------------------------------------Connector Pin Assignment7)
11----------------------------------------------------------------Other External Device6)
11----------------------------------------------------------------VCR, Video Printer5)
10----------------------------------------------------------------Power4)
10----------------------------------------------------------------Monitor3)
10----------------------------------------------------------------Camera2)
9----------------------------------------------------------------HDD(Hard Disk Drive)1)
9----------------------------------------------------------------Detailed Installation3-2.
8----------------------------------------------------------------Installation Configuration3-1.
8----------------------------------------------------------------InstallationCHAP. 3
7----------------------------------------------------------------Rear2-2.
5----------------------------------------------------------------Front2-1.
5----------------------------------------------------------------Function of Each ButtonCHAP. 2
4----------------------------------------------------------------Package Contents1-2.
3----------------------------------------------------------------Features1-1.
3----------------------------------------------------------------Features & Package ContentsCHAP. 1

Best picture quality DVR
JPEG2000 Stand-alone DVR
2
Contents
25----------------------------------------------------------------System Information8.
54----------------------------------------------------------------SpecificationsCHAP. 7
38
43
45
49
----------------------------------------------------------------
----------------------------------------------------------------
----------------------------------------------------------------
----------------------------------------------------------------
Remote Viewer Program
Back-Up CD Player
DDNS function
FAQ
6-2.
6-3.
6-4.
6-5.
31----------------------------------------------------------------DVR Network Configuration6-1.
29----------------------------------------------------------------RS-232C Setup2.
29----------------------------------------------------------------TCP/IP Setup1.
28----------------------------------------------------------------External Device5-6.
28----------------------------------------------------------------Back-Up5-5.
31----------------------------------------------------------------Network SetupCHAP. 6
30----------------------------------------------------------------Language Setup5-8.
30----------------------------------------------------------------FACTORY Default5-7.
29----------------------------------------------------------------Pan Tilt Zoom Setup3.
27----------------------------------------------------------------Holiday Setup3.
27----------------------------------------------------------------Schedule Setup2.
26----------------------------------------------------------------Record Configuration1.
26----------------------------------------------------------------Record Setup5-4.
25----------------------------------------------------------------Password Setup7.
25----------------------------------------------------------------Buzzer Setup6.
24----------------------------------------------------------------Alarm Setup5.
24----------------------------------------------------------------Interval Setup4.
22----------------------------------------------------------------Camera Setup3.
22----------------------------------------------------------------TIME/DATE Setup2.
21----------------------------------------------------------------HDD Management1.
21----------------------------------------------------------------Configuration5-3.
20----------------------------------------------------------------Monitor Setup2)
20----------------------------------------------------------------Screen Display1)
20----------------------------------------------------------------Display Setup5-2.
19----------------------------------------------------------------Entering the Menu5-1.
19----------------------------------------------------------------Set UpCHAP. 5

Best picture quality DVR
JPEG2000 Stand-alone DVR
3
Live View
Real time display per camera
Auto Sequence
PIP (Picture in picture)
Digital Zoom
Display Freeze
Simple Playback mode
Simple PTZ camera control
Record
Variable Record resolution (For higher picture quality or higher recording speed)
Efficient Image Quality setup in 5 steps
Schedule Record / Holiday Record
Event Record (Alarm / Motion)
Emergency Record
Network
View Live and Playback images across IP network
Copy images across the network
Playback
Search & Playback by Date/Time, Event, Camera
Outstanding picture quality by JPEG 2000 compression algorithm (No mosaic effect)
Suitable for recording not only images but also text
Various steps in Forward Playback Speed (X1/16, X1/8, X1/4, X1/2, X2, X4, X16, X32, X64)
Various steps in Backward Playback Speed (X1/16, X1/8, X1/4, X1/2, X2, X4, X16, X32, X64)
Easy and convenient search by Jog Shuttle & Remote Controller
Data Back-Up
Simple Back-Up using built-in CD Writer (Back-up CD Player included in the package)
Network Back-Up using Remote Viewer program(Remote Viewer included in the package)
Supports bigger capacity of HDD (400GB or bigger)
Others
Multi-Language (English, Spanish, Portuguese, German, French, Italy, Japan, Chinese)
VGA support both TFT LCD monitor and CRT monitor (option)
Lock the system by Password
JOG / SHUTTLE
PAL/NTSC Auto detection
Control the unit by using Remote Controller
CHAP. 1 Features & Package Contents
CHAP. 1 Features & Package Contents
1-1. Features

Best picture quality DVR
JPEG2000 Stand-alone DVR
4
CHAP. 1 Features & Package Contents
1-2. Package Contents
1. DVR Main Unit 2. Remote Controller
3. Power Cable
4. Power Adapter 5. User’s Manual
6. Software CD
7. Battery for remote controller 8. Bolts
For attaching Hard Disk Drive into DVR8. Bolts
Battery for remote controller7. Battery
Remote Viewer Software & Back up CD player6. Software CD
User’s Manual5. User’s Manual
12 V DC power supply to DVR main board4. Power Adapter
AC power supply to adapters for 12 V DC power3. Power Cable
DVR control2. Remote Controller
STAND-ALONE DIGITAL VIDEO RECORDER1. DVR Main Unit
DescriptionPackage Contents

Best picture quality DVR
JPEG2000 Stand-alone DVR
5
Reduce or increase the option value in the menu
Navigate in the menu
Move to next step
Selects each menu option
Set up for SYSTEM MENU or Use to exit the menu
Search recorded data on HDD
Playback of recorded data on HDD
Record Stop, Playback Stop, or Return to Schedule Record
from Emergency Record
Emergency Record at continuous, 60ips, SUPER FINE size
•F4 : USER 4
•F3 : USER 3
•F2 : USER 2
•F1 : USER 1
•AUTO : AUTO SCAN
•GOTO : GOTO PRESET
•CLEAR : CLEAR PRESET
•SET : SET PRESET
ENTER
MENU⑥SETUP
SEARCH
PLAY
+ -
▲▼◀▶
NEXT
STOP
REC⑤Record /
Playback
•TELE : ZOOM OUT
•WIDE : ZOOM IN
•FAR : FOCUS FAR
•NEAR : FOCUS NEAR
•CLOSE: IRIS CLOSE
•OPEN : IRIS OPEN
•OFF : LIGHT OFF
•ON : LIGHT ON
2. Control PTZ camera (Each button is assigned for each PTZ command)
1. Pressing this button will display a full screen image of that camera④Camera
selection
&
PTZ camera
control
IR receiver③IR
Firmware upgrade by connecting PC with latest firmware to USB port②USB Device
Shows status of operation①LED Lamps
FunctionName
CHAP. 2 Function of Each Button
2-1 FRONT
CHAP. 2 Function of Each Button

Best picture quality DVR
JPEG2000 Stand-alone DVR
6
⑩CD-RW
⑨Jog Shuttle
⑧Jog Shuttle
Control
Very easy and convenient search : Press J. Shuttle button, and images in
playback pause, and Jog and Shuttle makes it very easy and convenient to
search, forward or backward, fast and slow, as user want.
ACTIVE LED on : When J. SHUTTLE button is pressed
RUN LED on : While you operate Jog or Shuttle
Pressing Jog Shuttle button (Ready for use Jog/Shuttle)
: In playback mode, pressing J. SHUTTLE button make
images frozen.
Lock the key function
Auto camera image sequencing in full screen mode
Display in PIP (Picture in Picture) mode
Switch to split display
Freezing an Image
Zooming an image
On/Off for PAN/TILT/ZOOM control mode
Press this button first to control PTZ camera connected to
DVR unit via RS-485
Data Back-up using built-in CD writer
J.SHUTTLE
K.LOCK
SEQ
PIP
MODE
FRZ
ZOOM
PTZ⑦LIVE View
Control
FunctionName
CHAP. 2 Function of Each Button

Best picture quality DVR
JPEG2000 Stand-alone DVR
7
CHAP. 2 Function of Each Button
2-2. REAR
4 Channel
8 Channel
16 Channel

Best picture quality DVR
JPEG2000 Stand-alone DVR
8
3-1. Installation Configuration
CHAP. 3 Installation
CHAP.3 Installation
10
9
8
7
6
5
4
3
2
1
MONITOR
Output
LOOP Output
CAMERA Input
RS-232C
ETHERNET
VGA
SENSOR Input
Connection with PTZ Camera or other external device using RS 485
interface (Pin 1: D- / Pin 2: D+)
RS 485
POWER
SWITCH
DC Power
VCR Output
Power ON/OFF
DC power input (DC12V, 10A )
Connection with VCR for analog backup
Connection with Composite Monitor
Camera loop out
Connection with camera
Connection to external device as PC using RS-232C to control the DVR
Connection to ETHERNET device
Connection to VGA Monitor (CRT type or TFT LCD monitor)
Sensor input terminal(Pin 6,7 : Ground,
Pin 8 ~15 : Sensor input)
Relay out terminal (Pin 3: Relay COM / Pin 4: NC / Pin 5 : NO)RELAY Output
FunctionName

Best picture quality DVR
JPEG2000 Stand-alone DVR
9
1) HDD
1. Connect Main Board and HDD using IDE cable and HDD power cable.
2. The jumper setting of HDD should be on Master if you install only one HDD.
3. The jumper setting of HDD1 should be on Master and HDD2 should be on Slave if you install
two HDDs.(Refer to the above figure)
4. Stick the HDD absorber (included in package) on the bottom of case and then install the HDD
on top of them by using the bolts (included in package).
5. Screws must be inserted from outside of the case bottom.
CHAP. 3 Installation
3-2. Detailed Installation

Best picture quality DVR
JPEG2000 Stand-alone DVR
10
2) Camera
3) Monitor
Connect cameras to the camera input on rear panel of DVR marked CAMERA IN.
Connect the video output marked MONITOR to Video In of Main monitor.
4) Power
Insert the ADAPTER to the rear power socket of DVR.
ADAPTER specification: Input AC 110~240V / Output DC12V 10A
CHAP. 3 Installation

Best picture quality DVR
JPEG2000 Stand-alone DVR
11
5) VCR
6) Other External Device
Connect VCR or VIDEO Printer to VCR out on the rear panel of DVR.
SENSOR
SIREN
PAN/TILT
CAMERA
VGA
MONITOR
RS-232C : Control DVR through RS-232C port by using PC.
RS-485 : Control external device like PTZ Camera (Pin 1, 2 at Terminal Block).
RELAY Output : Relay Output (Pin 3 ~5 at Terminal Block).
SENSOR Input : SENSOR Input (Alarm connection)
ETHERNET : Connection to LAN, WAN, Internet.
VGA : Connection with VGA monitor(CRT,TFT LCD).
Select VGA in DISPLAY SETUP menu before connection to VGA monitor.
Setting VGA option board (For both CRT type PC monitor or TFT LCD monitor)
CHAP. 3 Installation

Best picture quality DVR
JPEG2000 Stand-alone DVR
12
7) Connector Pin Assignment
8) RS-232C ASCII-code
Signal GroundGND5
9Data Terminal dataDTR4
RS232C: Rx/Tx dataCTS8Transmit dataTxD3
RS232C: Rx/Tx dataRTS7Receive dataRxD2
Data Set ReadyDSR6Data Carrier DetectDCD1
DescriptionNODescriptionNo
Co m m Port
RS-232C
1 5
6 9
’@’
CH12
‘5’
CH5
‘L’
J.SHU
‘>’
+
‘U’
UP
’!’
CH11
‘4’
CH4
‘Q’
SEQ
‘<‘
-
‘M’
MENU
’#’
CH13
‘6’
CH6
‘C’
KLOCK
‘T’
PTZ
‘J’
DOWN
’0’
CH10
‘3’
CH3
‘I’
PIP0x0dENTER
‘E’
SERCH
’^’
CH16
‘9’
CH9
‘2’
CH2
‘D’
MODE
‘N’
NEXT
‘P’
PLAY
’%’
CH15
‘8’
CH8
‘1’
CH1
‘F’
FRZ
‘K’
RIGHT
‘S’
STOP
’$’
CH14
‘7’
CH7
‘Y’
QPLAY
‘Z’
ZOOM
‘H’
LEFT
‘R’
REC
Following ASCII-Codes(Hexa-Code) are for programmers who want to control DVR unit
via the RS232C Port using keyboard of PC.
All ASCII-Code is 1 Byte.
CHAP. 3 Installation

Best picture quality DVR
JPEG2000 Stand-alone DVR
13
4-1. Start-up DVR
CHAP. 4 Operation
Before turning on the DVR be sure that everything is firmly connected. Turn on the DVR and g
o to the Menu using the relevant Login Password and you will then see the System Setup Screen.
You may proceed by referring to the related chapters describing the various functions.
4-2. System Log-In
DVR LOG-IN
ENTER PASSWORD : _ _ _ _ _ _ _ _
INPUT YOUR OWN PASSWORD
TO EXIT, PRESS [MENU]
1) To enter into the setup menu, press the [MENU] button.
2) Enter password with channel number button
from No.1 to No.10 on the front of the DVR unit.
(Maximum of 8 digits are available)
3) After inputting the password, press the [ENTER] button.
Administrator :
If the password entered matches previously set password, “ LOGIN ADMIN” message appears and
you can enter into SYSTEM SETUP.
If the password entered does not match previously set password, the DVR unit goes back to live
display mode.
Factory default password is blank. For log-in, just press [MENU] button, followed by the [ENTER]
button.
-Factory default password
ADMIN : (NULL)
MANAGER : ‘ 1 ’
USER 1~USER8 : ‘ 2 ’ ~ ’ 9 ’
※We recommend configuring a unique password as per the procedure in
SYSTEM MENU - CONFIGURATION - PASSWORD SETUP.
※For security reasons, be sure to make note of your own password.
CHAP.4 Operation

Best picture quality DVR
JPEG2000 Stand-alone DVR
14
2005/JUN/03 pm 08:05:18
CAM-01 CAM-02
CAM-03 CAM-04
3. Status of DVR system
Emergency Record (Red)
Schedule Record (Green)
Temporary Stop (White)
Stop
Forward Playback
Backward Playback
Pause
1/16~1/2x forward playback
1/16~1/2x backward playback
2~16x forward playback
2~16x backward playback
16~64x forward playback
16~64x backward playback
4-4. Display Configuration
CHAP 4. Operation
1. Current Time & Date
2. Camera Title
ETHERNET status
HDD Status
In live mode : Amount of data recorded
In Playback mode : Amount of data played
LIVE Display
4-3. Factory Default
Before initial configuring or operation you must first set Time/Date, followed by setting the
unit to the FACTORY DEFAULT settings, lastly clearing the HDD. Please follow these steps
in order. Improper operation may result if this action is not taken.
DISPLAY SETUP
CONFIGURATION
REOCRD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE
HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM IMFORMATION
DISPLAY SETUP
CONFIGURATION
REOCRD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE
Refer to page 31.
Refer to page 22.
1. HDD CLEAR 2. FACTORY DEFAULT
ALARM Record
MOTION Record
CONTINUOUS Record
BASIC
NORMAL
ENHANCED
FINE
SUPER FINE
50/60 IPS @ 720x240
4 Channel
100/120 IPS @ 360x240
8/16 Channel
100/120 IPS @ 720x240
200/240 IPS @ 360x240

Best picture quality DVR
JPEG2000 Stand-alone DVR
15
CHAP. 4 Operation
3) Picture in Picture(PIP View)
When it is in full screen display mode, you can see other camera in a small
window by pressingping [PIP].The other camera in small window is rotating
in sequence to next number of camera and you can set the rotating time
interval as per the procedure in SYSTEM MENU-CONFIGURATION-
INTERVAL SETUP.
CAM-01
4) Freeze View
Full display mode : If you press the [FREEZE] button, the “F” character will be shown beside
camera title, and live image will be frozen.
Split display mode : If you press the [FREEZE] button, press the channel button which you
want to freeze.To release frozen image, press channel number of frozen
image again and press [FREEZE] button to exit FRZ mode.
5) Zoom View
In full screen, press the [ZOOM] button and move the Selection Frame using direction keys to the
area which you want to enlarge. And then press the [ENTER] button for 2-times enlarged picture.
To exit Zoom mode, just press [ZOOM] button again.
CH16
1) Full / Multiple View
Switch to multi-screen display by pressing [MODE]. For full image display, just press the channel button
which you want or [MODE] button again.
2) View in Sequence
Press [SEQ] button. It automatically displays full screen images in sequence.
4-5. Live View Setup
Full screen
Multi-screen
CH15
CH02
CH01
●
●
●
Full screen
[MODE] [MODE] or Channel button
2

Best picture quality DVR
JPEG2000 Stand-alone DVR
16
2005/JUN/03 pm 08:05:18
CAM-01 CAM-02
CAM-03 CAM-04
CHAP. 4 Operation
4-6. Record
Recording mode set before delivery by manufacturer (Default recording mode) is Schedule Recording.
In this default recording mode, it records 24 hours/day continuously in weekday and on the weekend.
Once you press the [REC] button while you see live view, the record type is changed to Emergency Record mode.
- Emergency Record
Record type : CONTINUOUS, SUPER FINE quality,
4CH: 60 (50) ips at 720X240 (720x288)
8/16CH:120(100) ips at 720X240 (720x288)
- Schedule Record
Record and stop as set (time interval and
record type) in RECORD-SCHEDULE SETUP menu.
- Temporary Stop
Temporary Record stop as set in
RECORD-SCHEDULE SETUP menu.
On the screen
- Emergency Record
: Red Record Icon ( ) and Record LED is lit
- Schedule Record
: Green Record Icon ( ) and Record LED is lit
- Temporary Stop
: White Icon ( ) and Record LED is off
- Motion Record
: Record standby LED blinks
: Record LED is lit
※While in Emergency Record mode, press [STOP],
[PLAY], [MENU], or [SEARCH] button to exit from
Emergency Recording mode and return to Schedule
Record mode.
※For details, refer to the SYSTEM MENU – RECORD
SETUP (Page 27)
- This DVR unit does not record in following conditions ;
※In Simplex mode, this unit does not record while entered in the menu or while it is in Playback mode.
※No camera is connected
※HDD is full and Overwriting is off in the Record Setup menu.
Emergency Record [RED]
Schedule Record [GREEN]
4-7. Playback
On record mode or stop mode, press [PLAY] button to play the recorded data in 1x speed.
For backward playback, press [PLAY] button again.
Use Jog/Shuttle to pause and control playback speed. To stop playback, press the [STOP] button.
Using Jog/Shuttle
press the [J.SHUTTLE] button in playback mode. The [ACTIVE] LED will be lit, and Jog/Shuttle is ready
for use. The [RUN] LED will blink whenever you operate the Jog/Shuttle.
For forward playback, turn the Shuttle right and turn Shuttle left for backward playback.
Turn Jog using your index figure to see picture by picture in forward or backward direction.
Operation of Shuttle is as follows.
1/4 x : 4 times slower than normal playback speed
1/2 x : 2 times slower than normal playback speed
1 x : Normal playback speed
2 x : 2 times faster than normal playback speed
4 x : 4 times faster than normal playback speed
16 x : 16 times faster than normal playback speed
64 x : 64 times faster than normal playback speed
If you want to keep the playback speed you selected using Shuttle, just hold the shuttle at that location for a few
seconds, and playback in speed you selected continues until you rotate Shuttle again.
Temporary Stop [WHITE]
J.SH U TTLE
RUN
ACTIVE

Best picture quality DVR
JPEG2000 Stand-alone DVR
17
CHAP. 4 Operation
4-8. Search
Press [SEARCH] button, and 3 different methods for searching recorded data are available as shown
in following SEARCH window. For selecting searching method, use direction key or Jog/Shuttle.
After selecting each search method, press [ENTER] button for playback.
1) SEARCH BAR
Search by percentage of total recorded data. It starts from image corresponding to set % of data
on the search bar.
2) TIME/DATE
Search by time & date. Playback starts from the time & date selected.
3) EVENT LIST
Search by event list (Motion, Alarm, Video Loss).
SEARCH
SEARCH BAR
TIME/DATE
EVENT LIST
SELECT MENU : ▲▼, & [ENTER]
RECORD SERCH BAR
[TARGET DATE/TIME]
020 %
SEARCH : [ENTER] , EXIT : [MENU]
TIME/DATE
[START] 2005/JUN/20 AM04:04:12
[ END ] 2005/JUN/20 PM08:12:23
INPUT DATE/TIME
2005/JUN/07 AM04:04:12
SEARCH : [ENTER] , EXIT : [MENU]
SEARCH page SEARCH BAR page
TIME/DATE page EVENT LIST page
EVENT LIST
SEARCH : [ENTER] , EXIT : [MENU]
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
----
----
----
----
----
----
----
--
--
--
--
--
--
--
TIME/DATEEVEN
T
001/000CH
SELECT : JOG SHUTTLE
SELECT : ef, EDIT : + -

Best picture quality DVR
JPEG2000 Stand-alone DVR
18
CHAP. 4 Operation
4-9. PAN/TILT/ZOOM Camera Operation
Press [PTZ] button first for PTZ control mode. Numeric buttons from 1 to 16 and direction buttons are
assigned for each PTZ command, and user can control PTZ camera connected to DVR unit by
pressing any one of those 20 buttons, one after the other, as needed, and it is just like control by
separate PTZ controller.
PTZ commandButton
PAN LEFT
PAN LEFT
TILT DOWN
TILT UP
FUNCTION
PRESET AUTO
PRESET GOTO
PRESET CLEAR
RIGHT BUTTON
LEFT BUTTON
DOWN BUTTON
UP BUTTON
13/F1 ~ 16/F4
12/AUTO
11/GOTO
10/CLEAR
9/SET
8/TELE
7/WIDE
6/FAR
5/NEAR
PRESET SET
ZOOM OUT
ZOOM IN
FOCUS FAR
FOCUS NEAR
IRIS CLOSE4/CLOSE
IRIS OPEN3/OPEN
LIGHT OFF2/OFF
LIGHT ON1/ON
PTZ commandButton
4-10. Data Back-Up
Enter into SYSTEM MENU-BACKUP-CDR SETUP.
1) Insert empty CD-R media into CD writer and select the start time & date from which you want to back up.
※The START & END time / date in HDD sub-menu only shows start and end of recording.
This is not selectable and editable.
※700MB on CD-R sub-menu represent size of CD-R media inserted.
2) To set start time of back-up and back-up data size, press the [ENTER] button first on [START] or [SIZE]
sub-menu and adjust using [+] or [-] button and move using [LEFT] and [RIGHT] button for next
change. After setting the time & date and back-up data size, press the [ENTER] button again to exit.
※End of back-up time will be calculated automatically as per start time & date and the back-up
data size you set.
※User can select the back-up data size (size of back-up data from start of back-up) on [SIZE] item but
END of back-up time is automatically determined by DVR system.
3) Press [ENTER] button on BURN sub-menu. DVR system starts burning CD.
4) When burning is completed, CD-R media will come out automatically. In the next CD back-up, start
time of CD-R shall be the end time of previous CD-back-up, and you can back-up from that for
continuous data back-up. If you need another backup, repeat the above procedure. To stop backup,
press the [MENU] button.
※During burning CD, it’s impossible to cancel burning process.
5) User can verify the back-up CD on PC with BACK-UP CD PLAYER (Included in Package).
CD-R SETUP
HDD
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
CD-R
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 000MB
BURN
SELECT MENU :cd, & [ENTER]
CD-R SETUP
HDD
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
CD-R 700 MB
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 700 MB - > 700MB
BURN
CD-RW BURNING : IMAGE DATA.
SELECT MENU :cd, & [ENTER]

Best picture quality DVR
JPEG2000 Stand-alone DVR
19
CHAP. 5 Set Up
5-1. Entering into the Menu
Enter into SYSTEM MENU by pressping [MENU] button.
Shuttle left turning : Reduce playback speed / Decrease value
Shuttle right turning : Increase playback speed / Increase value
Increase the option valuePLUS [+]
Jog left turning : Move backward to next image / Decrease value
Jog right turning : Move forward to next image / Increase value
Jog Shuttle
Move down side
Move to upper side
Move to next page
Selection key, Move to sub-menu, change status (ON or OFF)
Enter into SYSTEM MENU, Move to previous menu, ESC
MINUS [-]
RIGHT
LEFT
DOWN
Reduce the option value
Move to the right
Move to the left
UP
NEXT
ENTER
MENU
FunctionButton
SELECT MENU : ▲▼, & [ENTER]
LANGUAGE ENGLISH
EXTERNAL DEVICE
FACTORY DEFAULT
RECORD SETUP
BACK-UP
CONFIGURATION
DISPLAY SETUP
SYSTEM MENU
SCREEN DISPLAY
MONITOR SETUP
HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM INFORMATION
RECORD CONFIGURATION
SCHEDULE SETUP
HOLIDAY SETUP
TCP/IP SETUP
RS-232C SETUP
PAN/TILT SETUP
SYSTEM MENU
CHAP. 5 Set Up