Nero 800 User manual

4.
3.
2.
10.
8. Children should be supervised to ensure that they do not play with the appliance.
The iron must be used and rested on a flat, stable surface
The iron is not to be used if it has been dropped, if there are visible
Storage:
After using, pull out the plug and pour out the remaining water. Turn
the steam and the temperature control to “min”. Let the iron cool down,
then store the iron vertically in a safe and dry place.
Attentions:
1. Please read the owner’s manual before using the product.
2. Do not fill iron with any other liquid except water.
3. The iron must not be left unattended while it is connected to the
supply mains.
4. The plug must be removed from the socket outlet before the
water reservoir is filled with water.
5.
6.
Cautions:
1. Make sure that the applied voltage is the same as the rating
voltage.
If the supply cord is damaged, it must be replaced by the
manufacturer, service agent or qualified persons in order to
avoid a hazard.
This iron is for household use only.
Do not immerse the iron into any liquid for cleaning.
Do not touch the hot metal plate, hot water, or steam to avoid
scalding.
Nero 800 Steam/Dry Iron
PRODUCT CODE:
742815 - Nero 800 Ceramic
Please read these instructions for use and have a
good look at the illustration before using the appliance
7. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
9. When placing the iron on its stand, ensure that the surface on which the
stand is placed is stable
signs of damage or if it is leaking.
11. Surfaces are liable to get hot during use.

Main technical parameters:
Type Rated voltage Rated
frequency Rated power
742815 220-240V 50Hz 2000-2400W
Characteristics and structure:
A: Soleplate I: Spray & Burst steam button
B: Skirt J: Auto off light
C: Handle K: Cord guard
D: Back Cover L: Pilot light
E: Spray ASM M: Temperature dial
F: Top cover N: Water tank
G: Fill cover O: Clean button
H: Steam knob
Filling water:
Spraying:
Press the spraying button, and water will spray out from the
spraying nozzle. Always keep enough water in the water tank.
Steam ironing:
1. To use steam ironing, turn the steam control to minimum
position and set the temperature control at the “…” or MAX
position.
2. When the indicator light goes out, turn the steam control to
the suitable position.
Burst of steam:
Set the temperature control at the “…” or MAX position, then
press down the burst of steam button.
Dry ironing:
Turn the steam control to minimum position, then set the
temperature control to the suitable position.
Self cleaning:
Fill with water, then plug the iron into the mains, Set the
temperature control to the maximum position. About 3 minute later,
press the self clean button for about 1 minute. Steam and hot water
will be sprayed to clean the steam chamber. For best results use this
function once every two weeks.
Anti-drip:
This iron is equipped with a drip stop function: the iron
automatically stops steaming when the temperature is too low to
prevent water from dripping out of the soleplate.
Anti-calc:
The Anti-calc function filtrate the minerals from the water to
prevent mineral residue build up at the steam chamber.

1. Before filling water, please pull out the plug first.
2. Set the steam control to the minimum position.
3. Pull down the cover of water filling mouth, then fill water.
1 Year Warranty
Imported By R Weatherdon & Co Pty Ltd
Sydney - Australia
www.weatherdon.com.au
Made in China
Automatic shut off:
If the iron is switched on and not moved for a period of 8 minutes
while standing on its heel,
or 30 seconds while standing on the
soleplate, an internal safety feature will switch the iron off and the auto
shut off indicator will blink. Move the appliance sharply to switch it on
again.