Nero 8101-2M User manual

Remote Control is designed to control remotely the executive devices of the Radio series, as well as
executive devices of the Radio series using transcoder Nero 8361 UPM.
1.1. Purpose
Passport
Radio 8101-2M
Two-channel Remote Control
1.2. Specifications
Operating frequency range, MHz............................................................................................433,05 - 434,79
Maximum power of emitted signal, not more than, MW.................................................................................10
Number of control channels................................................................................................................................2
Battery type.............................................................................................................................................CR2032
Battery voltage, V................................................................................................................................................3
Overall dimensions, mm......................................................................................................................40×67×10
Operation temperature range, °С..................................................................................................from 0 to +40
Degree of frame protection...........................................................................................................................IP40
1. Device description
1.3. Peculiarities
Remote Control has three operation modes:
- step-by-step control («UP-STOP-DOWN-STOP» commands are executed circle-wise for every channel);
- differential control for every channel (definite command «UP» or «DOWN» is transmitted by pressing the button);
- compound control (differential control – for the first channel and step-by-step control – for the second one);
- transmission of control commands with static or dynamic code. Factory setting – dynamic code.
When controlling the executive device in static mode, it is possible to copy the remote control signal by an attacker, which will allow him to
control your object (roller shutter, barrier, gate). The possibility of copying and hacking is excluded in dynamic mode. Dynamic transmission
of the radio remote control is supported only by devices released after 2015. More information you can find in manual for device,
and applying to manager or the technical support service, the telephone number of which you can find on the manufacturer's website.
1
1
Channel 1
Channel 2
2. Programming
Action
Indication
Recording the remote control channel into the memory of the executive device
1. Input the executive device in the programming mode (see manual
for the corresponding device).
2. Record the control channel of remote control:
a) with dynamic transmission code: press and hold the
recordable channel button, and press short any other;
b) with static transmission code: press short the recordable
channel button.
Confirmation of record on the executive device depends on the
programming type and mode: short-long-short green flash on the
indicator or long-term movement «DOWN», short-term «UP-DOWN»
movement and long-term «UP» movement of the roller shutter.
The executive device supports only the static transmission code if the remote control is not recorded.
Changing the remote control code: selection of dynamic or static code
1. Press and hold any remote control button, and press short the
second button. Do not release the first button until the end of
programming.
2. Change the transmission type: press short any other remote
control button. The control transmission type is switched circle-wise
each time you press the second button.
- double flash – dynamic code (factory operation mode);
- triple flash – dynamic code with high range.
1. The indicator blinks off for 2 sec. Then the indicator of the remote
control blinks red:
- single flash – static code;
Changing the operation modes of the remote control channels
2. Changing the operation mode of the remote control: press and
hold one button of the remote control and press short any other.
The modes are switched circle-wise each time you press the
combination of buttons.
1. Enter into the mode of changing of the remote control settings:
press sequentially the four buttons of the remote control and hold
them together for more than 4 sec. (the remote control is in the
mode of changing the settings for 16 sec., then output will carried
out automatically).
- triple flash – compound control (differential control – for the first
channel and step-by-step control – for the second one).
- single flash – step-by-step control for every channel;
The indicator of the remote control blinks red:
- double flash – differential control for every channel;
Delete the remote control channel from the memory of the executive device
b) with static code: press and hold the erasable channel
button for more than 1 sec.
1. Input the executive device in the programming mode (see manual
for the corresponding device).
a) with dynamic code: press and hold the erasable channel
button, and then press any other for more than 1 sec.
2. Delete the control channel:
Confirmation of deletion on the executive device depends on the
programming type and mode: one long-term red flash or long-term
«DOWN-UP» movement of the roller shutter.

At the end of the service life the device is subject to disposal. The
device does not pose a hazard to human health and environment. The
device does not contain any non-ferrous and precious metals. Waste
batteries should be disposed separately from mini remote controls.
4. Current maintenance
If during operation the device fault is detected it is necessary to call
maintenance personnel. Within the warranty period servicing and
repair are provided by the manufacturer dealer.
5. Storage and transportation, service life
The devices should be stored in packing at temperatures from +5°C to
+40°C and relative humidity of not more than 80% in heated and
vented warehouses, in air-conditioned depots without corrosive
contaminants, conductible dust, acid and alkali vapors and gases
causing corrosion and insulation breakdown.
The devices should be transported packaged, in containers, closed
railway cars, heated and air-tight compartments of aircraft and holds
and by trucks with rain and snow protection for any distances at
temperatures from -50°C to +50°C and relative humidity of 100% at
25°C.
Average service life is 5 years min.
6. Disposal Remote Control Radio 8101-2M (see serial number on the first page)
is manufactured in conformance with RB TR 100376351.002-
2003, is approved by QCD and is classified as fit for operation.
Warranty obligations cease in case of non-observance of operating
conditions established by the manufacturer and mechanical damage
during operation. Warranty obligations do not cover the case of
failure to present the device passport.
Guaranteed storage life is 6 months from the manufacturing date
(the last 6 figures in the product serial number, for example: 191117
– November 19, 2017).
7. Manufacturer's warranty
Guarantee service life is 24 months from the date of sale.
Remote Control Radio 8101-2M ......................................................1 pc.
9. Acceptance certificate
With the note of sale absent – from the manufacturing date.
Passport ...........................................................................................1 pc.
8. Completeness
Individual packing ..............................................................................1 pc.
10. Potential problems
Problem
Probable reason
Fault elimination
The remote control is not recorded in
the executive devices.
1. Battery has run down (LED is off or blinks
when you press the remote control).
2. The remote control in dynamic mode is not
recorded in the executive devices which support
only static transmissions.
2. Change the operation mode from dynamic to
static one.
1. Change battery.
Action
Indication
DPM. The remote control should be programmed previously in the executive device.
b) delete channels of recorded remote controls from the memory
of executive device;
d) output the executive device from the DPM: press and hold the
previously recorded channel button of the remote control, and
then press short any other button.
2. You can perform the following actions when the executive device
is input into the DPM:
1. Input the executive device into the DPM from the previously
programmed remote control: press and hold the recorded channel
button and any other button for more than 4 sec., then release both
buttons and press short the recorded button twice during 5 sec.
a) record channels of new remote controls into the memory of
executive device;
c) erase all memory of the executive device: press and hold the
recorded channel button of the remote control and any other
button for more than 4 sec.
1. Roller shutter curtain will make a short-term movement «DOWN-
UP» once, and after 5 sec. by repeated short-term movement «DOWN-
UP» it will confirm the input in the DPM.
b) Roller shutter curtain will make long-term movement
«DOWN-UP».
2. Indication on the executive device:
a) Roller shutter curtain will make long-term movement «DOWN»,
short-term movement «UP-DOWN», and long-term movement «UP».
c) Roller shutter curtain will make long-term movement «DOWN-UP»
twice.
d) Roller shutter curtain will make short-term movement
«DOWN-UP» twice.
3. Distance Programming Mode (DPM)
2
Made in Belarus Ver. 1
SketchNero Group LLC
Tel.: [phone]
[phone]
[e-mail]
technical support:
Representative offices
in Russian Federation:
15, Bolshaya Ochakovskaya St.,
119361, Moscow.
8 800 5000-930
Manufacturer and representative
office in Belarus
www.neroelectronics.by
technical support:
Nero Electronics LLC
Tel.: [phone]
[e-mail]
[phone]
Minsk FEZ, 223016, Minsk district,
Novy Dvor Rural Council, 74
[phone]
Representative office
in Ukraine:
21, B. Khvoyki St., Office ,
03022, Kiev.
Tel.: [phone]
[phone]
[e-mail]
[phone]
Umnye resheniya LLC
technical support:
195009, St. Petersburg
[e-mail]
Nero SPb LLC
14, Komsomola St., Build. 2,
Tel.: [phone]
[phone]
technical support:
8 800 5000-930