Nero 8101-5 User manual

1
1
1. Purpose
Remote Control is designed to control remotely the executive devices
of the Radio series, as well as executive devices of the Nero series
(only with static code) using transcoder Nero 8361 UPM.
Five-channel Remote Control 8101-5
Passport
2. Specifications
Operating frequency range, MHz........................................................................................433,05–434,79
Maximum power of emitted signal, not more than, MW...........................................................................10
Number of control channels..........................................................................................................................5
Number of devices for feedback mode (one per channel)...........................................................................5
Battery type (number of pieces) ................................................................................................CR2032 (2)
Battery voltage, V...........................................................................................................................................3
Overall dimensions, mm...............................................................................................................129×40×15
Operation temperature range, °С.............................................................................................from 0 to +40
Degree of frame protection.....................................................................................................................IP40
3. Peculiarities
- transmission of control commands with static or dynamic code. Factory setting – dynamic code.;
- 5 control channels plus 1 shared channel. The shared channel is not available for programming, it only
manages devices;
- operation mode* with improved dynamic code and feedback support.
This mode is necessary for visual confirmation of remote control commands. If the device does not
respond to the command, the remote control reports an error with three beeps and three flashes of the
corresponding channel indicator. If the command is executed successfully, there are no instructions.
*Remote control operation modes:
1 - static;
2 - dynamic;
3 - improved dynamic (default settings);
4 - improved dynamic with feedback.
4. Programming
Fig. 1 — Assignment of remote control buttons
Channel indicator
Сhannel selection
UP/TURN ON
STOP/TURN OFF
DOWN/OFF
Action
Indication
Recording the remote control channel into the memory of the executive device
a) in dynamic mode: press the «STOP» button and, without releasing it, briefly press the «UP »
button, then release both.
1. Input the executive device in the programming mode (see manual for the corresponding device).
2. Select a recorded channel.
3. Record a channel:
b) in static mode: briefly press the «STOP» button.
c) in dynamic mode with feedback:
- press the «STOP» and «UP» buttons simultaneously;
- release the «UP » button without releasing the «STOP» button- get a signal from the remote
about successful recording to the device.
- channel recorded: 1 beep and 1 flashing diode of the recorded channel;
- channel not recorded: 3 beeps and 3 flashing diodes of the recorded channel.
Confirmation of record on the executive device depends on the programming type and mode: short-long-
short green flash on the indicator or long-term movement «DOWN», short-term «UP-DOWN» movement
and long-term «UP» movement of the roller shutter.
Remote display in dynamic mode with feedback:
Changing the remote control code: selection of dynamic or static code
3. Exit the menu: press and hold the «STOP» button for more than 1 second. The remote control will
also automatically exit the menu after 8 seconds.
2. Select the desired mode by short pressing the «UP» or down buttons.
1. Enter the «remote control mode Selection» menu: press and hold the «STOP» button for more
than 4 seconds.
2 flashes — dynamic operation mode;
3 flashes — improved dynamic mode;
2. Number of flashes of the remote control indicator:
4 flashes — improved dynamic mode of operation with feedback.
1. All channel indicators start blinking.
1 flash — static mode;
Delete the remote control channel from the memory of the executive device
1. Input the executive device in the programming mode (see manual for the corresponding device).
2. Select a deleted channel.
a) in dynamic mode: press the «STOP» button and without releasing it, briefly press the
«DOWN» button, release both.
3. Delete a channel:
c) in dynamic mode with feedback:
b) in static mode: press and hold the «STOP» button for more than 1 second, then release;
-press simultaneously button «STOP» and «DOWN» button;
-release the «DOWN» button while holding down the «STOP» button.
- channel not deleted: 3 beeps and 3 flashing diodes of the deleted channel(see the instructions on the
remote control) in red.
- channel deleted: 2 beeps and 2 flashing diodes of the channel being deleted;
Confirmation of deletion on the executive device depends on the programming type and mode: one long-
term red flash or long-term «DOWN-UP» movement of the roller shutter.
Remote display in dynamic mode with feedback:
Сalibration (removing devices that did not respond to the remote control in feedback mode)
Calibrate the remote control: press the «DOWN» and «UP» buttons simultaneously, release any of
them after the first beep, and press it again. Hold the buttons until you get a response from the
remote control (but no more than 8 seconds).
When you calibrate the remote control, all channels are cleared of devices that did not respond to
the remote request.
Information from the remote control:
3 beeps and 3 flashes of all indicators.
Opening / closing control channels
1. Enter the menu for closing / opening channels: press and hold the channel selection button for
more than 4 seconds.
2. Select the desired channel by short pressing the channel selection button.
3.
a) Close the channel: press the «DOWN» button.
b) Open a channel: press the «UP» button.
4. Exit the channel opening/closing menu — automatically after 5 seconds.
b) channel open: 1 long flash.
a) channel closed: 3 short flashes;
2. The indicator for the selected channel is not lit.
3. Indication:
1. 4 remote control channel indicators are lit (all except the first one).

Guarantee service life is 24 months from the date of sale.
At the end of the service life the device is subject to disposal. The device does not pose a hazard to
human health and environment. The device does not contain any non-ferrous and precious metals.
Waste batteries should be disposed separately from mini remote controls.
Warranty obligations cease in case of non-observance of operating conditions established by the
manufacturer and mechanical damage during operation. Warranty obligations do not cover the case of
failure to present the device passport.
9. Disposal
Products must be transported in package in containers, closed railway cars, heated sealed
compartments of aircraft and holds, as well as automobile transport with protection against
precipitation at any distance at temperatures from -50°С to + 50°С, and with relative humidity up to
100% - at 25°С.When transporting products, protection from dust and atmospherical condensation
should be provided.
The average product life is at least 5 years.
8. Storage, transportation, service life
7. Current maintenance
10. Manufacturer's warranty
Guaranteed storage life is 6 months from the manufacturing date (the last 6 figures in the product
serial number, for example: 191120 – November 19, 2020).
If during operation the device fault is detected it is necessary to call maintenance personnel. Within
the warranty period servicing and repair are provided by the manufacturer dealer.
Products should be stored in packaging at temperatures from + 5°С to + 40°С and relative air humidity
of no more than 80% in heated and naturally ventilated warehouses, in air-conditioned warehouses in
the absence of aggressive impurities, conductive dust, acid fumes and alkalis, as well as gases that
cause corrosion and destroy insulation. During storage, sharp fluctuations in temperature (more than
3°C/min) and air humidity (more than 5%/min) are not allowed.
With the note of sale absent – from the manufacturing date.
13. Potential problems
DPM is not available for static and feedback mode!
5. Distance Programming Mode (DPM)
Action
Indication
DPM. The remote control should be programmed previously in the executive device
1. Enter the DPM with the pre-programmed remote control: press the «STOP» button of the
recorded channel and, while holding it, press the «UP» button. Hold both buttons for more than 4
seconds, then release them and briefly press the up button twice for 5 seconds.
2. After entering the DRP, you can perform the following actions:
a) record the channels of new remotes to the device memory;
c) erase all device memory: press the «STOP» and «DOWN» buttons of the recorded remote
channel simultaneously, hold them for more than 4 seconds;
d) output the device from the DRP: press and hold the «STOP» button of the recorded channel of
the remote control, then briefly press the «UP» button.
b) delete channels of recorded remotes from device memory;
1. Roller shutter curtain will make a short-term movement «DOWN-UP» once, and after 5 sec. by
repeated short-term movement «DOWN-UP» it will confirm the input in the DPM.
b) Roller shutter curtain will make long-term movement
«DOWN-UP».
a) Roller shutter curtain will make long-term movement «DOWN», short-term movement «UP-DOWN»,
and long-term movement «UP».
d) Roller shutter curtain will make short-term movement
«DOWN-UP» twice.
c) Roller shutter curtain will make long-term movement «DOWN-UP» twice.
2. Indication on the executive device:
6. Updating the remote control
The 8101-5 remote control can receive new updates if you have an online 8767 device. You must log in on your 8767 device. The update is only available in the feedback mode.
Action
Indication
The battery of the remote control must be charged, otherwise the update will not be installed (error alarm).
1. Simultaneously press and hold the «UP» and «DOWN» buttons until the second channel led lights
up and the second beep sounds, then release both buttons.
2. In the app, add the remote control and activate the update download.
1. The indicators of all channels, from the 1st to the 5th, start flashing in waves.
2. The indicators continue to flash until the update is installed, and then turn off.
The remote control is updated within 10 minutes, forced interruption is available by the "stop" button.
Fig. 2 — Replacing batteries
11. Completeness
Remote Control Radio 8101-5 (see serial number on the first page) is manufactured in conformance
with RB TR 808001034.012-2018, is approved by QCD and is classified as fit for operation.
12. Acceptance certificate
Remote Control Radio 8101-5 ...............................................................................................................1 pc.
Passport ..................................................................................................................................................1 pc.
Individual packing ...................................................................................................................................1 pc.
Made in Belarus
2
Version 1
SketchNero Group LLC
technical support:
15, Bolshaya Ochakovskaya St.,
119361, Moscow.
8 800 5000-930
Representative offices
in Russian Federation:
Tel.: [phone]
[phone]
[e-mail]
Nero Electronics LLC
Tel.: [phone]
Manufacturer and representative
office in Belarus
www.neroelectronics.by
[phone]
[phone]
Minsk FEZ, 223016, Minsk district,
Novy Dvor Rural Council, 74
[e-mail]
technical support:
[phone]
[e-mail]
technical support:
21, B. Khvoyki St., Office ,
03022, Kiev.
Representative office
in Ukraine:
Umnye resheniya LLC
Tel.: [phone]
[phone]
Tel.: [phone]
[phone]
technical support:
Nero SPb LLC
195009, St. Petersburg
14, Komsomola St., Build. 2,
[e-mail]
8 800 5000-930
Problem
Probable reason
Fault elimination
The remote control is not recorded in the executive
devices.
1. Battery has run down (LED is off or blinks when you press the remote
control).
2. The remote control in dynamic mode is not recorded in the executive
devices which support only static transmissions.
1. Change battery.
2. Change the operation mode from dynamic to static one.