NetComm LIBERTY 3G22WV User manual

NetCommWireless
Quick Start Guide
NetComm
Wireless
3G22WV
3G WiFi Router with Voice
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

NetComm
Wireless
Thanks for purchasing
neTcomm Wireless
This quick start guide is designed to get you up and running quickly with your new router. More
advanced set up instructions can be found in the user manual which can be downloaded from
www.netcommwireless.com
hardWare insTallaTion
Power adapter Power point
SIM
1. Insert your SIM card into the SIM card slot (you should hear it click into place)
2. For voice functionality, connect a standard analog telephone to the port labelled Voice using the
provided RJ-11 phone cable.
3. Connect the power adapter to the power socket on the back of the router.
4. Plug the power adapter into the wall socket and power on the device.
5. Wait approximately 1 minute for the router to start up.
6. To connect to the router via Ethernet cable, please go to Connecting to the router via a cable
section. To connect via WiFi, please go to Connecting to the router via WiFi on the next page.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

3G WiFi Router with Voice - 3G22WV
connecTing To The rouTer via a cable
Computer
NOTE: This step is optional. If you do not wish to connect via an Ethernet cable to the router, please skip this step and proceed to the
step below.
1. Connect the provided yellow Ethernet cable to one of the Ethernet ports on the back of the router.
2. Connect the other end of the Ethernet cable to your computer.
3. Wait approximately 30 seconds for the connection to establish.
4. Proceed to the Customize your routers settings step to congure Internet access on your router
CONNECTING TO THE ROUTER VIA WIFI
Smart Phone
Online Gaming
Laptop
Tablet
NOTE: This step is optional. If you do not wish to connect via WiFi to the router, please skip this step.
You can connect multiple WiFi devices, including laptops, desktops, tablets and PDA’s to your router by
following these basic steps.
1. Using your WiFi device, scan the WiFi networks in your area and select the wireless network name
listed on the included Wireless Security Card and then click connect.
2. Enter the wireless security key listed on the included Wireless Security Card.
3. Wait approximately 30 seconds for the connection to be established.
4. Proceed to Customize your routers settings step to congure Internet access on your router.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

NetComm
Wireless
QSG-00009 rev1
CUSTOMIZE YOUR ROUTER’S SETTINGS
To customize your router’s settings, please perform the following steps:
1. After establishing your wired or wireless connection as previously outlined, open your Web browser (
such as Firefox, Internet Explorer and Safari) and type http://192.168.20.1 into the address bar at the
top of the Web browser window and press Enter.
2. You will be brought to the Status page. From here you can see the current connection status of
your router.
3. Click on the Login tab and enter the default Username and Password of admin, and then press
Submit to login to the management console.
4. Click on the Internet tab to congure the settings to get you online.
5. You can Enable or Disable the Internet connection to allow your router to get online.
6. The router attempts to automatically congure and may have already connected to the Internet. If it
hasn’t, you may need to congure a custom APN and/or authentication settings. To do this, untick
the checkbox Automatically Congure My Mobile Broadband. Hover over the blue Choose an
APN here link and select your mobile service provider to auto-ll the APN of your 3G network. If you
have a special APN, please enter it manually.
7. Fill in the PIN settings of your SIM, if required, and then click Save to use the settings you have entered.
8. Click on the Wireless tab to congure the WiFi settings of your router. Please note that Wireless
settings do not need to be changed and the default settings can be used.
9. Enter the WiFi Network Name (SSID) and WiFi Password (WPA2-PSK) and then click Save to use the
settings you have entered.
The router will now apply your changes. If a connection is successfully established, the blue network
light on the front of the router will light up. When connecting devices via WiFi, the settings that were
entered will have to be used.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]