NETGEAR FS102 User manual

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Congratulations on your purchase of the NETGEAR™Model FS102, Model FS104, or Model
FS108 Fast Ethernet Switch—a low-cost, high-performance network solution designed to support
power workgroups operating at 10 megabits per second (Mbps) or 100 Mbps.
In this installation guide that describes how to install and use the switches, all three switches are
referred to collectively as the Model FS102/FS104/FS108 switch. Each switch is listed
individually when information is provided that refers to a specific model.
The Model FS102/FS104/FS108 switch has the following features:
• Two (Model FS102 switch), four (Model FS104 switch), and eight (Model FS108 switch)
vista automatic speed-sensing 10/100 Mbps Ethernet ports that provide fast information
exchange, resource sharing, and client or peer-to-peer communication using standard
Category 5 unshielded twisted pair (UTP) cable
• Automatic address learning function to build the packet forwarding information table (The
table contains up to 8,000 MAC addresses; that is, the switch can support networks with as
many as 8,000 devices.)
• Autosensing full-duplex or half-duplex mode of operation (Full-duplex mode doubles
throughput of point-to-point connections by letting individual ports transmit and receive
concurrently when the connecting device also supports full-duplex mode.)
• Wire-speed filtering and forwarding to support the “traffic cop” function by directing traffic
to the appropriate port or network segment without slowing down the traffic
• Easy plug-and-play installation with no software to configure, which saves time and
minimizes the potential for configuration errors
• Normal/Uplink push button to simplify network extension (The switch can be connected to
another switch or hub using a standard, straight-through cable.)
• Two vista RJ-45 connector ports on the Model FS102 switch, four vista RJ-45 connector
ports on the Model FS104 switch, and eight vista RJ-45 connector ports on the Model FS108
switch (Each port has built-in LEDs to monitor individual port status.)
• LEDs that provide network traffic status and data transmission speed
• IEEE 8023u standard compliance, allowing incorporation with other 100BASE-TX Fast
Ethernet (100 Mbps) products
• IEEE 802.3 10BASE-T standard compliance
• Compact, sturdy metal case design that enables easy desktop, wall-mount, or under-desk
installation
Start Here
Features

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Verify that your package contains the following:
• Model FS102, Model FS104, or Model FS108 switch
• Mounting kit (for wall installation)
• This installation guide
• Warranty & Owner Registration Card
• Support Information Card
• AC power cord and universal power cord adapter
Package Contents
8900FA
Universal
power cord
adapter
Wall mount
installation kit
Installation guide,
Warranty & Owner
Registration Card,
and Support
Information Card
Model FS108 switch
Model FS102 switch Model FS104 switch
or
or
AC
power
cord
1
12345678
234 56 78
Power Collision
100 Mbps LINK Rx
FS108
FAST ETHERNET SWITCH
2
FS102
FAST ETHERNET SWITCH LINK Rx
1
12
Collision
100 Mbps
1
1234
23
Power Collision
100 Mbps
FS104
FAST ETHERNET SWITCH LINK Rx
4

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Fast Ethernet Vista Ports with Built-in LEDs
All of the ports on the switch are 10/100 Mbps Ethernet ports. The network access speed for the
ports is automatically sensed and displayed on the front panel by the 100 Mbps LEDs.
Each port supports only unshielded twisted pair (UTP) cable using an 8-pin RJ-45 plug.
Each port uses vista RJ-45 connectors that have two LEDs—the Link LED and the FDX LED.
Product Illustration
8899FA
Front Panel of the Model FS102 switch
Front Panel of the Model FS108 switch
1
12345678
234 56 78
Power Collision
100 Mbps LINK Rx
FS108
FAST ETHERNET SWITCH
Power 2
FS102
FAST ETHERNET SWITCH LINK Rx
1
12
Collision
100 Mbps
100 Mbps ports
Normal/Uplink
push button
Power
Front Panel of the Model FS104 switch
1
1234
23
Power Collision
100 Mbps
FS104
FAST ETHERNET SWITCH LINK Rx
4
8724EB
Link
LED FDX LED

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
LEDs
This table describes the activity of the Model FS102/FS104/FS108 switch LEDs.
Label Color Activity Description
Pwr (Power) Green On
Off Power is supplied to the switch. Power is disconnected.
Rx/Tx/Collision Green
Yellow
Blinking
Blinking
Packet transmission or reception is occurring on the port.
Data collisions are occurring on the port. The blinking action
corresponds to the number of collisions. When a collision
occurs, the connected device pauses and transmits again
after waiting a specified time. Note that occasional collisions
are normal.
100 Mbps Green On
Off
The port is operating at 100 Mbps.
The port is operating at 10 Mbps.
Link
(located at the
top left corner
of each vista
10BASE-T port)
Green On
Off
A valid link is established on the port.
A link is not established on the port.
FDX
(located at the
top right corner
of each vista
10BASE-T port)
Green On
Off
The port is operating in full-duplex mode.
The port is operating in half-duplex mode.

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Normal/Uplink Push Button
The Normal/Uplink push button on the front panel of the switch allows you to select uplink (MDI)
or normal (MDI-X) wiring for either of the Ethernet ports on the Model FS102 switch, port 4 on
the Model FS104 switch, or port 8 on the Model FS108 switch. These ports are configured for
normal wiring to connect to a PC when the push button position is out. When the push button is
pressed in, these ports are configured for uplink wiring to connect to another switch or to a hub,
using a straight-through twisted pair cable.
Rear Panel
The rear panel of the Model FS102/FS104/FS108 switch has full-duplex (FDX) and auto-duplex
(AUTO) toggle switches and a power adapter receptacle for the supplied power adapter.
FDX/AUTO Duplex Toggle Switches
Full-duplex mode is supported for all 10/100 Mbps ports and allows the port to transmit and
receive data at the same time. Full-duplex operation applies only to point-to-point access (for
example, when a switch is connected to a PC, a server, or another switch).
Setting the toggle switch to AUTO on the 10/100 Mbps port enables the port to determine duplex
mode automatically. In this mode of operation, the 10/100 Mbps port operates in either full- or
half-duplex, depending on the operating mode of the remote port. If the remote port cannot
provide the proper signal to indicate its capability, the 10/100 Mbps port on the switch defaults to
half-duplex mode. Repeaters and hubs use a common collision domain for all communications
and cannot communicate in full-duplex mode. The associated 10 Mbps port on the switch should
be set to auto-duplex operation when connecting to these types of devices.
One toggle switch is assigned to each 10/100 Mbps port and can be set to full-duplex (FDX) mode
or auto-duplex (AUTO) mode.
12Vdc 1.2A
– +
12Vdc 1.2A
– +
8901FA
Rear Panel of the Model FS102 switch
Rear Panel of the Model FS104 switch
Rear Panel of the Model FS108 switch
Power receptacle
14FDX
AUTO
10/100 Mbps
FDX -
AUTO - Force port to operate at Full Duplex and Half Duplex mode. Enable port to determine duplex mode
automatically. Default is Half Duplex.
12Vdc 1.2A
– +
12345678FDX
AUTO
10/100 Mbps
FDX -
AUTO - Force port to operate at Full Duplex and Half Duplex mode. Enable port to determine duplex mode
automatically. Default is Half Duplex.
12FDX
AUTO
10/100 Mbps
FDX -
AUTO - Force port to operate at Full Duplex and Half Duplex mode. Enable port to determine duplex mode
automatically. Default is Half Duplex.

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
The Model FS102/FS104/FS108 switch is designed to provide flexibility in configuring your
network connections. Each switch can be used as a standalone device or can be used with 10 Mbps
or 100 Mbps hubs or other interconnection devices in various configurations. The configuration
examples in this section illustrate the integration of the switches in various network environments
using other NETGEAR products. These examples include a network of a few workstations
connected to a printer or a segmented network with multiple users or workgroups and other
networking devices.
Although the examples illustrate specific switches, any of the switches can be used in the network
configurations shown.
Desktop Switching
The Model FS108 switch is used as a desktop switch to build a small network that enables users to
have 100 Mbps access to a file server.
If a full-duplex adapter card is installed in the server or PC, a 200 Mbps connection is possible on
the port where the server or PC is connected.
Applications
1
12345678
234 56 78
Power Collision
100 Mbps LINK Rx
FS108
FAST ETHERNET SWITCH
Model FS108 switch
100 Mbps
10 Mbps
8902FA
Key

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Segment Switching
The Model FS108 switch is used as a switch that segments a network into multiple connected
pieces, increasing overall bandwidth and throughput. The Model FS108 switch can segment
networks that are built with the NETGEAR Model DS108 Dual Speed Hubs.
Extending a Network Diameter
Ethernet specifications limit the length of cable between hubs and PCs to 100 meters (m) for a
total of 200 meters. By adding Fast Ethernet switches between hubs, a network is expanded by 200
meters with the addition of each switch. The illustration below shows two NETGEAR Model
FE108 Fast Ethernet Hubs integrated with a Model FS108 switch to extend a network.
1
12345678
234 56 78
Power Collision
100 Mbps LINK Rx
FS108
FAST ETHERNET SWITCH
Auto 10/100 MbpsDUAL SPEED Auto 10/100 MbpsDUAL SPEED
Model FS108 switch
Model DS108 hubModel DS108 hub
8903FA
1
12345678
234 5678
Power Collision
100 Mbps LINK Rx
FS108
FAST ETHERNET SWITCH
Model FS108 switch
100 m
8904FA
Model FE108
hubs

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Bridging from 10BASE-T to 100BASE-TX Networks
The Model FS108 switch can function as a two-port bridge connecting traditional 10BASE-T
Ethernet networks to 100BASE-TX Fast Ethernet networks. Users requiring increased network
bandwidth can be upgraded to 100 Mbps while remaining connected to the rest of the network by
integrating the Model FS108 Fast Ethernet Switch with the NETGEAR Model EN108 Ethernet
Hub and the NETGEAR Model FE108 Fast Ethernet Hub.
High-Bandwidth File Servers
The Model FS104 switch increases bandwidth for workgroups and strengthens network
throughput when accessing high-volume file servers. The switch provides parallel communication
between each of the ports. This method of communication allows multiple conversations to occur
concurrently, expands overall throughput, and allows key servers or other heavily used devices to
be available to more users. The Model FS104 Fast Ethernet Switch can be integrated with a
NETGEAR Model FE108 Fast Ethernet Hub and a NETGEAR Model DS108 Dual Speed Hub. A
full-duplex configurable adapter card installed in the server provides up to 200 Mbps maximum
data throughput.
1
12345678
234 56 78
Power Collision
100 Mbps LINK Rx
FS108
FAST ETHERNET SWITCH
1234 56 78
Pwr
Col
EN108
10BASE-T HUB LINK Rx
Model EN108
hub
Model FE108 hub
8967FA
Model FS108 switch
200 Mbps
100 Mbps
10 Mbps
Key
Auto10/100 MbpsAuto10/100 Mbps DUAL SPEED
Model FS104
switch
Model FE108 hub Model DS108 hub
8906FA

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Before you begin installing your switch, prepare the installation site. Make sure your operating
environment meets the operating environment requirements of the equipment.
To install your switch on a flat surface, you do not need any special tools. Be sure the switch is
positioned with at least 2 inches of space on all sides for ventilation.
To install the switch on a wall, measure the distance between the mounting holes on the back of
the switch and mark the wall to match the location of the mounting holes on the switch. At the
marks, screw into the wall the two screws in the mounting kit included in your package contents.
Choose a location that is near the devices to be connected, is close to an electrical outlet, and
provides at least 2 inches of space all around the switch for ventilation.
Before connecting the switch, be sure you review “Applications” for to determine the appropriate
configuration for your networking needs.
To connect the switch:
1. Connect the devices to the 10/100 Mbps ports on the switch, using Category 5 UTP
cable and an RJ-45 plug.
2. Set the Normal/Uplink push button.
The Normal/Uplink push button eliminates the need to use a crossover twisted pair cable for
daisy-chaining or cascading. Use the following guidelines to configure port 1 and port 2 on
the Model FS102 switch, port 4 on the Model FS104 switch, or port 8 on the Model FS108
switch for uplink or normal wiring:
• Configure the port for normal wiring if the port is to be connected to an uplink-wired
device, such as a network station or a PC.
• Configure the port for uplink wiring if the port is to be connected to a normal-wired
device, such as a 100 Mbps hub or another switch.
The remaining (normal) ports on the switch cannot be configured for uplink wiring. If you are
using one of these ports to connect to another normal port, you must use a crossover twisted
pair cable to connect the two ports. Refer to “Cable and Connector Information” for
information about crossover twisted pair cable and straight-through twisted pair cable.
Characteristic Requirement
Temperature Ambient temperature between 0
q
and 40
q
C (32
q
and 104
q
F).
No nearby heat sources such as direct sunlight, warm air exhausts, or
heaters.
Operating humidity Maximum relative humidity of 90%, noncondensing.
Ventilation Minimum 2 inches (5.08 cm) on all sides for cooling.
Adequate airflow in room or wiring closet.
Operating conditions At least 6 feet (1.83 m) to nearest source of electromagnetic noise (such
as photocopy machine or arc welder).
Power Adequate power source within 6 feet (1.83 m).
Note: Ethernet specifications limit the cable length between your PC or server and the
switch to 328 feet (100 meters).
Prepare the Site
Install the Switch
Connect Devices to the Switch

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
3. Set the FDX or AUTO toggle switches on the rear panel for the selected duplex mode.
A hub and repeater use a common collision domain for all communications and cannot
support full-duplex mode. When connecting any of the 10/100 Mbps ports on the switch to a
hub, set the port to AUTO. The switch must also be set to AUTO when connecting to any
device that does not use NWay autonegotiation to detect the operating mode. Setting the
toggle switch to AUTO will cause the port to default to half-duplex mode when connecting to
a port that does not use autonegotiation.
When connecting to a PC, a server, or another switch, the duplex setting for the port must be
the same as the duplex setting on the PC, server, or other switch.
To set the 10/100 Mbps ports for the selected duplex mode:
• Move the toggle switch into the down position (to AUTO) for auto-duplex mode.
The 10/100 Mbps ports will negotiate and automatically determine the duplex mode
based on the mode of the connected port. If the connected port cannot autonegotiate,
the 10/100 Mbps port will default to half-duplex mode. The factory setting of the duplex
toggle switches is AUTO.
• Move the toggle switch into the up position (to FDX) for full-duplex mode.The duplex
switch must be set to FDX if you are connecting to legacy full-duplex 100 Mbps devices
that do not generate signals indicating duplex mode. If the duplex switch is set to AUTO
mode, the 10/100 Mbps ports will default to half-duplex mode because the port does not
receive the proper signal.
4. Connect one end of the DC power adapter cable to the power outlet on the rear panel of
the switch and the other end of the power adapter cable to the wall outlet.
When power has been applied to the switch:
• The green Pwr (Power) LED on the front panel is on.
• The green Link LED on each connected port is on.
When the switch is connected and operating, refer to the table in “LEDs” for information about
the LEDs and their activity.
Verify Installation

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Symptom Cause Solution
Green Link LED is
off on an active
port.
Port connection is
not functioning. Make sure the attached device is powered and there is a proper UTP connection at that end.
Make sure the network adapter card installed in the
PC is in working condition. Verify that the network
adapter card is100 Mbps capable and that the 100
Mbps LED and Link LEDs are on at the network
adapter card in the PC.
Make sure the proper cable is installed, and check for
miswired cable pairs or loose connectors.
Green Link LED is
intermittent on an
active port.
Port connection is
not functioning. Make sure the port termination at both the switch and the device end is correct. Check the crimp on the RJ-
45 connectors. In a Fast Ethernet operation, the
quality of the crimp on the connector is important. It is
also important that only Category 5 cable is used and
that it is certified for 100 Mbps operation.
Make sure the length of the UTP cable from the switch
to the device does not exceed 328 feet (100 meters).
Using cable test equipment, make sure the cable
meets the crosstalk, attenuation, and impedance
specifications as required by the 100BASE-TX
standard. Refer to “Cable and Connector Information”
for information about cable specifications.
Green Link LED is
off on ports 1 or 2
on the Model
FS102 switch, port
4 on the Model
FS104 switch, or
port 8 on the
Model FS108
switch.
Port connection is
not functioning. Check the Normal/Uplink push button on the front panel.
If you are using a straight-through cable connected to
a PC or other MDI-wired device, make sure the
Normal/Uplink push button is set in the Normal
position.
If you are using a straight-through cable connected to
a router or another switch, make sure the Normal/
Uplink push button is set in the Uplink position.
Try the alternate position of the Normal/Uplink push
button to turn the Link LED on.
Refer to “Cable and Connector Information” for cable
information.
Green 100 Mbps
LED is off when
operating in a Fast
Ethernet network.
Port is operating in
10 Mbps mode. Make sure the adapter card is capable of 100 Mbps operation and set for 100 Mbps operation if it is not
autosensing.
Green Link LED is
on and Green FDX
LED is off when
connected to a full
duplex network.
Port is operating in
half-duplex mode. Make sure the duplex switch on the Model FS102/ FS104/FS108 switch is set for full-duplex operation.
Make sure the connected device is capable of full-
duplex transmission.
Troubleshooting Information

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
Twisted Pair Cables
For two devices to communicate, the transmitter of each device must be connected to the receiver
of the other device. The crossover function is usually implemented internally as part of the
circuitry in the device. Most ports on switches and repeaters have media-dependent interfaces with
crossover ports. These ports are referred to as MDI-X or normal ports. Computer and workstation
adapter cards are usually media-dependent interface ports referred to as MDI or uplink ports.
The figures illustrate the use of straight-through and crossover twisted pair cables.
Yellow Rx/Tx
Collision LED is
blinking
excessively.
Data collision is
occurring on the port. The port and switch might be functioning correctly. However, check the following to make sure that
excessive collisions are normal (as in most Ethernet
networks) and not caused by:
• Incorrect cabling or connectors
• Wiring techniques
• Mismatched duplex operating mode settings
Green FDX LED is
off when you have
set the port to
operate in full-
duplex mode.
Port is operating in
half-duplex mode. Make sure the connected device is able to operate at half-duplex mode and check the specifications of the
connected device to make sure it has the ability to
signal the operating mode. Verify that the connected
device is operational. If the connected device is an
adapter card, make sure you have an adapter card
that is capable of 100 Mbps operation and set to 100
Mbps if it is not autosensing.
Symptom Cause Solution
Cable and Connector Information
Straight-through
twisted pair cable
Crossover
twisted pair cable
8146EB
Tx
Uplink or
MDI port Normal or MDI-X port
Normal or
MDI-X port Normal or MDI-X port
Rx
1
2
3
6Tx
Rx
1
2
3
6
1
2
3
6
1
2
3
6
Tx
Rx
Tx
Rx

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
RJ-45 Connector
The RJ-45 connector (shown in the illustration with an RJ-45 plug) is used to connect
workstations and switches through unshielded twisted pair cable. The RJ-45 connector accepts
four-pair Category 3 or Category 5 UTP cable. Only two pairs are used for 10BASE-T wiring.
RJ-45 Connector
Pin Assignment Normal Assignment:
Uplink Assignment:
Port 1 or 2 on the Model FS102 Switch
Port 4 on the Model FS104 Switch
Port 8 on the Model FS108 Switch
1 Input Receive Data + Output Transmit Data +
2 Input Receive Data - Output Transmit Data -
3 Output Transmit Data + Input Receive Data +
6 Output Transmit Data - Input Receive Data -
4, 5, 7, 8 Not used Not used
711EA
18
12345678

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
General Specifications Model FS102 Switch Model FS104 Switch Model FS108 Switch
Network Protocol and
Standards Compatibility ISO/IEC 802-3 (ANSI/IEEE 802.3i) 10BASE-T Ethernet
IEEE 802.3u, IEEE802.3x 100BASE-TX, Fast Ethernet
Data Rate 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX
10 Mbps differential Manchester encoded
Interface RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface
Power Consumption 8 W 15.2 W 12 W
Input Voltage
(Power Adapter) 12 V dc 12 V dc 5 V dc
Physical Specifications
Dimensions: 6.2 x 1.06 x 4.1 in.
15.8 x 2.7 x 10.3 cm 9.27 x 1.06 x 4.1 in. 23.5 x 2.7 x 10.3 cm 9.27 x 1.06 x 4.1 in. 23.5 x 2.7 x 10.3 cm
Weight: 1.09 lb; 0.50 kg 1.60 lb; 0.73 kg 1.60 lb; 0.73 kg
Environmental Specifications
Operating temperature: 0
q
to 40
q
C (32
q
to 104
q
F)
Operating humidity: 90% maximum relative humidity, noncondensing
Electromagnetic
Emissions CE mark, commercial; FCC Part 15, Class A; EN 55 022 (CISPR 22), Class A;
VCCI Class 1 ITE
Electromagnetic Susceptibility
CE mark, commercial CE mark, commercial CE mark, commercial
Electrostatic discharge
(ESD): IEC 801-2, Level 2/3/4 IEC 801-2, Level 2/3/4 IEC 801-2, Level 2/3/4
Radiated electromagnetic
field: IEC 801-3, Level 2 IEC 801-3, Level 2 IEC 801-3, Level 2
Electrical fast transient/burst: IEC 801-4, Level 2 IEC 801-4, Level 2 IEC 801-4, Level 2
Electrical surge: IEC 801-5, Level 2 IEC 801-5, Level 2 IEC 801-5, Level 2
Safety Agency Approvals
for Power Adapter CE mark, commercial
UL listed (UL 1950)
CSA certified
(CSA 22.2 #950)
TUV licensed
(EN 60 950)
T-Mark
CE mark, commercial
UL listed (UL 1950)
CSA certified
(CSA 22.2 #950)
TUV licensed
(EN 60 950)
T-Mark
CE mark, commercial
UL listed (UL 1950)
CSA certified
(CSA 22.2 #950)
TUV licensed
(EN 60 950)
T-Mark
Performance Specifications
Frame filter rate: 14,800 frames/second, maximum on 10 Mbps port
148,000 frames/second, maximum on 100 Mbps port
Frame forward rate: 14,800 frames/second, maximum on 10 Mbps port
148,000 frames/second, maximum on 100 Mbps port
Network latency (using 64-
byte packets): 10 Mbps to 10 Mbps: 73 microseconds maximum 10 Mbps to 100 Mbps: 26 microseconds maximum
100 Mbps to 10 Mbps: 62 microseconds maximum
100 Mbps to 100 Mbps: 15 microseconds maximum
Address database size: 8,000 media access control (MAC) addresses per port
Addressing: 48-bit MAC address
Queue buffer: 10/100 Mbps ports: 1 MB of buffer space
for each port 10/100Mbpsports:128k of buffer space for each
port
Technical Specifications

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide
© 1998 by NETGEAR, Inc. All rights reserved.
Trademarks
Bay Networks is a registered trademark of Bay Networks, Inc.
NETGEAR is a trademark of Bay Networks, Inc.
All other trademarks and registered trademarks are the property of their respective owners.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products
described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model FS102/104/108 Fast Ethernet Switch has been suppressed in accordance with the conditions set out
in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the
regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right
to test the series for compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the first category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set
by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at preventing radio
interference in commercial and/or industrial areas.
Consequently, when this equipment is used in a residential area or in an adjacent area thereto, radio interference may be caused to equipment such
as radios and TV receivers.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference,
in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense.
EN 55 022 Statement
This is to certify that the NETGEAR Model FS102/104/108 Fast Ethernet Switch is shielded against the generation of radio interference in
accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class A
(CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS102/104/108 Fast Ethernet Switch) does not exceed the Class A limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR Model FS102/104/108 Fast Ethernet Switch) respecte les limites de bruits radioélectriques visant les appareils
numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take appropriate measures.

NETGEAR, Inc.
A Bay Networks Company
4401 Great America Parkway
Santa Clara, CA 95054 USA
Phone: 888-NETGEAR
*M-FS100NA-1*