NETGEAR GS750E User manual

48-Port Gigabit Ethernet Smart
Managed Plus Switch
User Manual
Model GS750E
July 2017
202-11784-01
350 E. Plumeria Drive
San Jose, CA 95134
USA

Support
Thank you for purchasing this NETGEAR product.You can visit www.netgear.com/support to register your
product, get help, access the latest downloads and user manuals, and join our community.We recommend that
you use only official NETGEAR support resources.
Conformity
For the current EU Declaration of Conformity, visit http://kb.netgear.com/app/answers/detail/a_id/11621.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
©NETGEAR, Inc., NETGEAR, and the NETGEAR Logo are trademarks of NETGEAR, Inc.Any non-NETGEAR
trademarks are used for reference purposes only.
2
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

Contents
Chapter 1 Get Started
Configure the Switch..............................................................................................6
Access the Switch Using a Web Browser..............................................................6
Access a Switch That Is Off-Network................................................................6
Access a Switch That Is Connected to a Network.............................................7
Access the Switch Using the NETGEAR Insight App............................................7
Access the Switch With the ProSAFE Plus Utility..................................................7
Install the ProSAFE Plus Utility.........................................................................8
Access and Configure the Switch Using the ProSAFE Plus Utility....................8
Change the Password............................................................................................9
Register Your Product..........................................................................................10
Chapter 2 Manage Network Settings
Specify IP Address Settings for the Switch..........................................................12
Use Browser-Based Access to Specify the Switch IP Address.......................12
Use the ProSAFE Plus Utility to Specify the Switch IP Address.....................13
Manage Multicast Traffic With IGMP Snooping....................................................14
Customize IGMP Snooping.............................................................................14
Specify a VLAN for IGMP Snooping................................................................16
Enable the Auto-Video Configuration..............................................................17
Set Up Link Aggregation......................................................................................17
Set Up a Static Link Aggregation Group.........................................................18
Set Up a Link Aggregation Control Protocol Group.........................................19
Set Up the LACP System Priority for the Switch.............................................20
Set Up LACP Port Priority and Time-Out Values.............................................21
Chapter 3 UseVLANS forTraffic Segmentation
VLAN Overview....................................................................................................24
Create Basic Port-Based VLANs.........................................................................24
Assign Ports to Multiple Port-Based VLANs........................................................25
Create 802.1Q-Based VLANs in a Basic Configuration.......................................27
Create 802.1Q-Based VLANs in an Advanced Configuration..............................28
Add Tagged or Untagged Ports to an 802.1Q-Based VLAN................................29
Specify a Port PVID for an 802.1Q-Based VLAN.................................................31
Manage the Voice VLAN......................................................................................32
Specify the Voice VLAN Properties.................................................................33
Enable the Voice VLAN Mode for Ports...........................................................33
Manage the OUI Table.....................................................................................35
Chapter 4 Manage Security
Manage Access Control.......................................................................................38
Add Devices to the Access Control Table........................................................38
3

Remove Devices From the Access Control Table............................................39
Set the Switch Management Mode......................................................................40
Disable Bonjour for Discovery..............................................................................41
Manage the Auto Denial of Service Mode...........................................................41
Chapter 5 Optimize Performance With Quality of Service
Enable 802.1p/DSCP-Based Quality of Service..................................................44
Configure Port-Based Quality of Service.............................................................44
Set Up Rate Limiting............................................................................................46
Set Up Broadcast Filtering...................................................................................47
Chapter 6 Manage and Monitor the Switch
Manage Flow Control...........................................................................................50
Manage the Port Speed and the Port Status.......................................................51
Enable Loop Prevention.......................................................................................52
Manage Power Saving Options............................................................................53
Download and Upgrade the Firmware.................................................................54
Reboot the Switch................................................................................................55
Save the Switch Configuration.............................................................................55
Restore a Saved Switch Configuration................................................................56
Restore Factory Default Settings.........................................................................57
Enable Port Mirroring...........................................................................................57
View Switch Information.......................................................................................58
View or Clear the Port Statistics...........................................................................59
Chapter 7 Diagnostics andTroubleshooting
Test Cable Connections.......................................................................................62
Resolve a Subnet Conflict to Access the Switch..................................................63
Appendix A Factory Default Settings
4
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

1
Get Started
This chapter covers the following topics:
•Configure the Switch
•Access the Switch Using a Web Browser
•Access the Switch Using the NETGEAR Insight App
•Access the Switch With the ProSAFE Plus Utility
•Change the Password
•RegisterYour Product
For hardware information, see the hardware installation guide (HIG) for your switch model.
You can download the HIG by visiting downloadcenter.netgear.com.
Note
For more information about the topics covered in this manual, visit the support website
at netgear.com/support.
Note
Firmware updates with new features and bug fixes are made available from time to time
atdownloadcenter.netgear.com.Youcan checkforand download new firmwaremanually.
If the features or behavior of your product does not match what is described in this guide,
see the latest firmware release notes for your switch model.
Note
5

Configure the Switch
Smart Managed Plus Switches are plug-and-play, so they can be used without any configuration. Just
connect power, connect to your network and to your other devices, and you’re done.You can also configure
and manage additional advanced features of the switch either by using your computer’s web browser or by
installing the ProSAFE®Plus Utility on your Windows-based computer.
For easiest access, we recommend that you cable the switch to a network with a router or DHCP server
that assigns IP addresses, power on the switch, and then use a computer that is connected to the same
network as the switch (on-network). However, it is also possible to configure the switch connected directly
only to the computer that you are using to configure it, and not connected to the network (off-network).
Access the Switch Using aWeb Browser
This manual describes the web browser–based management interface.
You can access and configure the switch directly through its web browser–based management interface by
entering the switch’s IP address in the address bar of a browser.When using web-browser setup, the simplest
way to configure the switch is not connected to your network (off-network).You can also configure the switch
with it connected to your network, router, or modem, (on-network) but you must be able to determine the IP
address of the switch if your network uses DHCP.
Access a SwitchThat Is Off-Network
To use your web browser to configure a switch that is not connected to a network:
1. Record your computer’s TCP/IP configuration settings, and then configure the computer with a static
IP address of 192.168.0.210 and 255.255.255.0 as the subnet mask.
If you are unsure how to do this, visit the support website at netgear.com/support and
search for Static IP address on computer.
Note
2. Plug the switch into a power outlet and then connect your computer to the switch using an Ethernet
cable.
You can connect the Ethernet cable to any port on the switch.
3. Open a web browser, and enter http://192.168.0.239.
This is the default address of the switch.
4. When prompted, enter the password.
The default password is password.
5. Click the Login button.
You can now configure additional options for the switch in the web management interface.
6. After you complete the configuration of the switch, reconfigure the computer that you used for this
process to its original TCP/IP settings.
You can now connect your switch to your network using an Ethernet cable.
Get Started
6
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

Access a SwitchThat Is Connected to a Network
To use your web browser to configure a switch that is connected to a network:
1. Cable the switch to a network with a router or DHCP server that manages IP addresses.
2. Power on the switch.
The DHCP server assigns the switch an IP address.
3. Connect your computer to the same network as the switch.
4. Determine the IP address of the switch.
DHCP is enabled on the switch by default. Use the IP address that the DHCP server assigned to the
switch. If you are unsure how to determine the IP address of the switch, you can use the ProSAFE®
Plus Utility or an IP scanner utility.
5. Open a web browser, and enter the IP address of the switch.
6. When prompted, enter the password.
The default password is password.
7. Click the Login button.
You can now configure additional options for the switch in the web management interface.
Access the Switch Using the NETGEAR Insight App
The switch supports the NETGEAR Insight app, which you can install on a mobile device.
Using the NETGEAR Insight app, you can discover the switch on the network, register it, and add the switch
to the NETGEAR Insight app.Once the switch is added to the NETGEAR Insight app, you can configure
basic management settings, locally monitor the switch status, and launch the web management interface.
You can choose from three methods to add the switch to the NETGEAR Insight app.All three methods
require that the smartphone on which the NETGEAR Insight app is installed is connected to the same
network as the switch. Use one of the following methods:
•Add the switch from the Day Zero discovery page.
•Add the switch from the Network page.
•Add the switch from the Device List page.
For more information, see the NETGEAR knowledge base articles at netgear.com/support.
Access the SwitchWith the ProSAFE Plus Utility
The ProSAFE Plus Utility runs on Windows-based computers.You can install the utility to select additional
options to manage and customize the switch for your network.The utility is located on the resource CD that
came with the switch.You can also visit netgear.com/support/product/PCU to download the utility.
Get Started
7
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

Install the ProSAFE Plus Utility
The ProSAFE Plus Utility requires WinPcap and Adobe Air. If WinPcap and Adobe
Air are not detected during the ProSAFE Plus Utility installation, you are prompted to
allow them to be installed.
Note
To install the ProSAFE Plus Utility from the resource CD:
1. Insert the resource CD into a computer that is connected to the switch.
The Resource CD page displays.
2. Click the Install ProSAFE Plus Utility link and follow the prompts to install the program.
The utility is installed in the program directory of your computer and a ProSAFE Plus Utility icon is
placed on your desktop.
3. If prompted, allow WinPcap and Adobe Air to be installed.
We recommend that you reboot your computer after installing the ProSAFE Plus
Utility.
Note
Access and Configure the Switch Using the ProSAFE Plus
Utility
For easiest access, we recommend that you cable the switch to a network with a router or DHCP server
that assigns IP addresses, power on the switch, and then use a computer that is connected to the same
network as the switch.
You can also access and configure the switch directly using a web browser. See
Access the Switch Using a Web Browser on page 6.
Note
To access and configure the switch using the ProSAFE Plus Utility:
1. Cable the switch to a network with a router or DHCP server that manages IP address.
2. Power on the switch.
The DHCP server assigns the switch an IP address.
3. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection.The computer and the switch must be on the same Layer 2
network.
4. Double-click the ProSAFE Plus Utility icon.
The configuration home page displays a list of Smart Managed Plus Switches that the utility discovers
on the local network.
Get Started
8
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

To use the ProSAFE Plus Utility, you must configure your computer’s security software
to allow broadcast UDP packets to go through UDP remote and source (local and
destination) ports 63321 through 63324.To allow this traffic, you can create a rule in
your computer’s security software, or temporarily disable the firewall, Internet security,
antivirus programs, or all of these on the computer that you use to configure the
switch. If you temporarily disable any security services, be sure to reenable those
services once configuration is complete.
Note
5. Select the Smart Managed Plus Switch that you want to configure.
If you do not see the switch, click the REFRESH button.
6. When prompted, enter the password.
The default password is password.
The Switch Information page displays.
7. Use the utility to configure the switch settings.
8. When you are finished with the configuration, return the computer’s firewall, Internet security, and
antivirus programs to their usual settings.
For a description of ProSAFE Plus Utility features, see the ProSAFE Plus Utility User Manual.You can
access the user manual through links on the Help tab of the utility or from the resource CD, or you can
download it by visiting downloadcenter.netgear.com.
Change the Password
The default password to access the switch is password.We recommend that you change this password
to a more secure password.The ideal password contains no dictionary words from any language and
contains uppercase and lowercase letters, numbers, and symbols. It can be up to 20 characters.
To change the password:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
5. Select Maintenance > Change Password.
The Change Password page displays.
Get Started
9
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

6. In the Old Password field, type the current password for the switch.
7. Type the new password in the New Password field and in the Re-type New Password field.
8. Click the Apply button.
Your settings are saved. Keep the new password in a secure location so that you can access the switch
in the future.
RegisterYour Product
Registering your product allows you to receive email alerts and streamlines the technical support process.
To register your product:
1. Connect your computer to the same network as the switch.
You can use a WiFi or wired network connection.
You must access the switch while connected to the network (on-network) to register
the switch.
Note
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
5. Select Help > Registration.
The Product Registration page displays.
6. Click the Register button.
7. Follow the onscreen process to register your product.
Get Started
10
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

2
Manage Network Settings
This chapter covers the following topics:
•Specify IP Address Settings for the Switch
•Manage Multicast Traffic With IGMP Snooping
•Set Up Link Aggregation
11

Specify IP Address Settings for the Switch
By default, the switch IP address works as follows:
•If you cable the switch to a network with a DHCP server before you power on the switch, the DHCP
server assigns an IP address to the switch when the switch is powered on.
•If you power on the switch when it is not connected to a network with a DHCP server, the switch uses
its default IP address, which is 192.168.0.239.
You can disable the DHCP mode in the switch and enter static IP address and subnet mask values for
the switch as well as the address of the gateway device used by the switch.
Use Browser-Based Access to Specify the Switch IP Address
To specify IP address settings for the switch:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
5. In the DHCP Mode menu, select Disable.
Manage Network Settings
12
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

The IP Address, Subnet Mask, and Gateway Address fields are enabled.
6. Enter the IP address, subnet mask, and gateway address.
7. Click the Apply button.
Your settings are saved.
Use the ProSAFE Plus Utility to Specify the Switch IP Address
To specify IP address settings for the switch:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Double-click the ProSAFE Plus Utility icon.
The Switch Selection page displays a list of Smart Managed Plus Switches that the utility discovers on
the local network.
3. Select the switch.
If you do not see the switch, click the REFRESH button.
4. Click the IP SETTING button.
To navigate to this page, select Network, select the switch, and click the IP SETTING
button.
Note
5. In the DHCP Mode menu, select Disable.
The IP Address, Subnet Mask, and Gateway Address fields are enabled.
6. Enter the IP address, subnet mask, and if available, the gateway address.
Manage Network Settings
13
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

7. Enter the switch’s password in the Password field.
The switch’s default password is password.
8. Click the APPLY button.
Your settings are saved.
Manage MulticastTraffic With IGMP Snooping
Internet Group Management Protocol (IGMP) snooping allows a switch to forward multicast traffic intelligently
on the switch. Multicast IP traffic is traffic that is destined to a host group.Host groups are identified by class
D IP addresses, which range from 224.0.0.0 to 239.255.255.255.Based on the IGMP query and report
messages, the switch forwards traffic only to the ports that request the multicast traffic.This feature prevents
the switch from broadcasting the traffic to all ports and possibly affecting network performance.
The switch maintains a map that shows which links need which IP multicast streams.The switch forwards
multicast traffic only to the links that requested them and cuts multicast traffic from links that do not contain a
multicast listener.Essentially, IGMP snooping helps optimize multicast performance at Layer 2 and is especially
useful for bandwidth-intensive IP multicast applications such as IPTV.
Customize IGMP Snooping
By default, IGMP snooping is enabled.You can customize the settings for your network.
To customize IGMP snooping:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
Manage Network Settings
14
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

5. Select System > Multicast.
6. Select the IGMP Snooping Status Enable radio button.
By default, the Enable radio button is selected.
7. Make sure that aVLAN ID between 1 and 4094 is stated in the VLAN ID Enabled for IGMP Snooping
field.
You can specify a VLAN for IGMP snooping only if you enabled port-based or 802.1Q-based VLANs
(see Use VLANS for Traffic Segmentation on page 23).
IGMP snooping functions only on theVLAN that is specified in the VLAN ID Enabled for IGMP Snooping
field.
8. (Optional) Select the Validate IGMPv3 IP header Enable radio button.
Somenetwork devices mightnot conformto theIGMPv3 standard.WhentheValidateIGMPv3 IPheader
option is enabled, IGMP messages are required to includeTTL = 1, ToS Byte = 0xC0 (Internetwork
Control), and the router alert IP option (9404) must be set. Otherwise, the packets are ignored.
9. (Optional) Select the Block Unknown MultiCast Address Enable radio button.
When this feature is enabled, multicast packets are forwarded only to the ports that are in the multicast
group learned from IGMP snooping. All unknown multicast packets are dropped.
10. (Optional) Select a port to be the dedicated IGMP snooping static router port if no IGMP query exists
in the network for the switch to discover the router port dynamically.
Select one of the following IGMP Snooping Static Router Port radio buttons:
•Auto. If the switch receives a query message, the switch configures the router port or ports
dynamically.This is the default setting.
•Any.IGMP Join and Leave packets are sent to every port of the switch.
•Static. Select one port as the dedicated IGMP snooping static router port by selecting the check
box that is associated with the port number. All IGMP Join and Leave reports are forwarded to the
selected port.
11. Click the Apply button.
Your settings are saved.
Manage Network Settings
15
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

Specify aVLAN for IGMP Snooping
You can specify a VLAN for IGMP snooping only if you enabled port-based or 802.1Q-based VLANs (see
Use VLANS for Traffic Segmentation on page 23).
To specify a VLAN for IGMP snooping:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
5. Select System > Multicast.
6. Select the IGMP Snooping Status Enable radio button.
By default, the Enable radio button is selected.
7. In the VLAN ID Enabled for IGMP Snooping field, enter the ID of the VLAN.
By default, if you enable IGMP snooping, snooping occurs onVLAN 1.However, you can enable snooping
on any VLAN:
•For port-based VLANs, you can enter a VLAN ID from 1 to 50.
•For 802.1Q-based VLANs, you can enter aVLAN ID from 1 to 4094.
8. Click the Apply button.
Your settings are saved.
Manage Network Settings
16
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

Enable the Auto-Video Configuration
You can enable the Auto-Video VLAN for IGMP snooping only if you enabled port-based or 802.1Q-based
VLANs (see UseVLANS forTraffic Segmentation on page 23).By default, the Auto-VideoVLAN is disabled.
The default ID of the Auto-Video VLAN is ID 3, which you cannot change.
To enable the Auto-VideoVLAN:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
5. Select System > Multicast > Auto-Video.
The Auto-Video Configuration page displays.
6. Select the Auto-Video Status Enable radio button.
By default, the Disable radio button is selected.
7. Click the Apply button.
Your settings are saved.
Set Up Link Aggregation
Link aggregation groups (LAGs) allow you to combine multiple Ethernet links into a single logical link.Network
devices treat the aggregation as if it were a single link, which increases fault tolerance and load sharing.
Configure LAG membership before you enable the LAG.The switch supports eight LAGs.
The switch supports both static link aggregation (port trunking) and Link Aggregation Control Protocol (LACP)
groups through IEEE 802.3ad Link Aggregation.
Set up link aggregation in the following order:
1. Set up the LAG on the switch.
2. Connect the ports that you made members of the LAG on the switch to the ports that are members of
a LAG on another device in your network.
For more information, see the following sections:
Manage Network Settings
17
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

•Set Up a Static Link Aggregation Group on page 18
•Set Up a Link Aggregation Control Protocol Group on page 19
•Set Up the LACP System Priority for the Switch on page 20
•Set Up LACP Port Priority and Time-Out Values on page 21
Set Up a Static Link Aggregation Group
The switch supports eight LAGs, which can be a combination of static link aggregation and LACP groups.
You must set up LAG membership before you can enable LAGs.
To specify LAG membership for a static LAG and enable a static LAG:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
5. Select System > LAG > LAG Membership.
6. In the LAG ID menu, select the LAG ID.
7. Enter a name in the LAG Name field.
You can enter a name of up to 15 alphanumeric characters.
8. Select the ports for the LAG by selecting the check boxes that are associated with the port numbers.
A LAG consists of at least two ports.
9. Click the Apply button.
Your settings are saved.
Manage Network Settings
18
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

10. Select System > LAG > LAG Configuration.
11. Select the LAG ID of the LAG for which you just set up the port membership.
12. In the Admin Mode menu, select Enable.
13. In the LAGType menu, select Static.
The Port Member field for the selected LAG ID shows the ports that you selected in Step 8.
The LAG Status field for the selected LAG ID shows whether the LAG is established (Up) or not
established (Down).
14. Click the Apply button.
Your settings are saved.
Set Up a Link Aggregation Control Protocol Group
The switch supports eight LAGs, which can be a combination of Link Aggregation Control Protocol (LACP)
groups and static link aggregation groups.
To specify an LACP group:
1. Connect your computer to the same network as the switch.
You can use aWiFi or wired network connection, or connect directly to a switch that is off-network using
an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch Using a Web Browser on page
6.
The login window opens.
4. Enter the switch’s password in the password field.
The switch’s default password is password.
The Switch Information page displays.
Manage Network Settings
19
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E

5. Select System > LAG > LAG Membership.
6. In the LAG ID menu, select the LAG ID.
7. Enter a name in the LAG Name field.
You can enter a name of up to 15 alphanumeric characters.
8. Select the ports for the LAG by selecting the check boxes that are associated with the port numbers.
A LAG consists of at least two ports.
9. Click the Apply button.
Your settings are saved.
10. Select System > LAG > LAG Configuration.
11. Select the LAG ID of the LAG for which you just set up the port membership.
12. In the Admin Mode menu, select Enable.
13. In the LAGType menu, select LACP.
The Port Member field for the selected LAG ID shows the ports that you selected in Step 8.
The LAG Status field for the selected LAG ID shows whether the LAG is established (Up) or not
established (Down).
14. Click the Apply button.
Your settings are saved.
Set Up the LACP System Priority for the Switch
The LACP system priority specifies the link aggregation priority of the switch relative to the devices at the
other ends of the links on which link aggregation is enabled.The default is 32768. A higher value indicates
a lower priority.The value of the priority applies to all LACP LAGs that you set up on the switch.
Manage Network Settings
20
48-Port Gigabit Ethernet Smart Managed Plus Switch Model GS750E