NEUTRIK etherCON NE8FDPS-TOP User manual

PRODUCT MANUAL
R
Example (NE8FDPS-TOP) of
preassembled Delivery.
®
etherCON TOP airtight
NE8FDPS-TOP & NE8FDIS-TOP & NE8FDPU-TOP
Panel thickness: ³ 2.0 mm [0.08")
(without airtightness) ³ 1.0 mm [0.04")
Step 1: Combine connector parts
ACombine flansh and sealing cap
P
Page 1BDA 692
ð
! Example of etherCON TOP Unmated connection options
NE8FDIS-TOPNE8FDPS-TOP NE8FDPU-TOP
1 Connector installation
etherCON/RJ45
to 2,54 mm box
header 2x4 pin
feedthrough,
D-shape flange
etherCON/RJ45
to straight RJ45
feedthrough,
D-shape flange
etherCON/RJ45
to 90° angled
RJ45 (upwards)
feedthrough,
D-shape flange.
A
IP 65 & IP 67 &
airtightness

N O T E : L u b r i c a t e s e a l i n g l i p w i t h
s i l i c o n f r o m t i m e t o t i m e .
C
Step 2: Assembly
BInsert the receptacle from the front into the
panel.
Position the screw and fasten it.
PRODUCT MANUAL - etherCON TOP airtight chassis connector
®
B
.
Panel thickness:
³ 2.0 mm [³ 0.08"]
Equipment / Panel
2x
Screws
D
AT T E N T I O N :
Tightening torque M = 40 - 50 Ncm
A
D
24.0 [.945"]
19.0 [.748"]
≥ Ø 3.2 [.126]
A Panel Cutout (Rear Side) B Recommended screw
5.3 - 6.0
[.201 - 0.236”]
90°
M3 stainless steel
countersunk type
2 Additional information
C
Page 2BDA 692
ð
⌖ ⌀ 0,1 [0.004] A
12.0 [.472"]
9.5 [.374"]
±0.1 ±0.003
Ø 24.0 [.945 "]
A
Rz £ 16

www.neutrik.com
Data subject to change without prior notice. 2023 NEUTRIK . NEUTRIK are registered trademark of Neutrik AG. ALL RIGHTS RESERVED.
® ®
©
Neutrik AG LI-9494 Schaan
I
A brand of the Neutrik Group
3 Application and Safety Instructions
A Assembly
l When assembling and processing the product, ensure the use of appropriate personal
protective equipment.
Neutrik components must only be assembled with designated and specified components.l
Replacement parts are suitable only when used in combination with the designatedl
components. The product's characteristics are guaranteed only in the intended combination.
B Application
l The product is exclusively intended for installation in electronic equipment or similar devices.
l The product is not intended for use in medical applications.
l The product is not intended for use in potentially explosive or flammable environments.
C Operation
l Before plugging in, check the contact area for dry surfaces.
l Product surfaces may cause burns at elevated ambient temperatures. Ensure the use of appropriate
protective equipment.
l Neutrik products should only be combined with products from Neutrik Group brands.
D Cleaning
l Clean only with dry and lint-free materials or compressed air.
l The product must not be cleaned while under load. The product may only be cleaned while it is not
connected to any voltage and without the use of cleaning agents.
E Damages
l Handle products with care.
l In case of visible damages, check the suitability of the product for use.
https://www.neutrik.com/en/products/audio/ethercon
i More Information on the website
PRODUCT MANUAL - etherCON TOP airtight chassis connector
®
Document No.: BDA 692 V1
Date: 2023-11-07