New Gate FACETEMP-SCAN User manual
FACETEMP-SCAN
User manual
User manual FACETEMPSCAN V-20200608 - ENGLISH
Face Recognition Terminal
User manual
Note
1. Device working temperature: 10 -40 Ć. Do not Install under the vent
and ensure that there is no heating source within 3 meters;
2. People entering the room from a cold outdoor environment will affect
measurement accuracy. The forehead temperature test needs to be
performed indoors without covering the forehead for three minutes and
the temperature is stable;
3. The temperature read by the temperature measuring device is the
temperature in the forehead area. When there is water, sweat, oil
orthick makeup on the forehead, or the elderly have wrinkles, the read
temperature will be lower than the actual temperature. Make sure there
is no hair or clothing covering this area.
-2-
-1-
1.3 Packing list
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 6* Tie 6. 1*Hex screwdriver
1.1 Introduction
The face recognition terminals are suitable for hotels, office buildings,
schools, shopping centers, KTV, bars, buses and communities.
1.2 Product Features
(1) Using high-precision infrared temperature detector non-contact
automatic body temperature detection;
(2) Temperature measurement range: 30-45 Ć, accuracy is ± 0.3
(3) Real-time output of identify results and voice prompts;
(4) Auto identify people without masks and sound real-time warning;
(5) Auto register and record information, avoid manual operation,
improve efficiency and reduce missing information;
(6) Dual sensor with living detect, face recognition distance 0.3-3M,
(7) Face recognition within 500ms; Face library 22400 person. Total
storage 100,000 recognize record;
(8) Supporting SDK and HTTP protocols under Windows / Linux
(9) Device vision dynamics 80dB, suitable for backlight environment;
(10) Supports fog, 3D noise reduction, strong light suppression,
electronic image stabilization, multiple white balance modes.
(11) Linux operate system more stable.
1 Product Overview
Packing list of 7-inch or 8-inch turnstile
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 1*Hex screwdriver 6. 1*Gimbal bracket
7. 1*wall mount bracket 8. 1*Screw kits
Packing list of 7-inch or 8-inch wall-mounted
Face Recognition Terminal
User manual
Note
1. Device working temperature: 10 -40 Ć. Do not Install under the vent
and ensure that there is no heating source within 3 meters;
2. People entering the room from a cold outdoor environment will affect
measurement accuracy. The forehead temperature test needs to be
performed indoors without covering the forehead for three minutes and
the temperature is stable;
3. The temperature read by the temperature measuring device is the
temperature in the forehead area. When there is water, sweat, oil
orthick makeup on the forehead, or the elderly have wrinkles, the read
temperature will be lower than the actual temperature. Make sure there
is no hair or clothing covering this area.
-2--1-
1.3 Packing list
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 6* Tie 6. 1*Hex screwdriver
1.1 Introduction
The face recognition terminals are suitable for hotels, office buildings,
schools, shopping centers, KTV, bars, buses and communities.
1.2 Product Features
(1) Using high-precision infrared temperature detector non-contact
automatic body temperature detection;
(2) Temperature measurement range: 30-45 Ć, accuracy is ± 0.3
(3) Real-time output of identify results and voice prompts;
(4) Auto identify people without masks and sound real-time warning;
(5) Auto register and record information, avoid manual operation,
improve efficiency and reduce missing information;
(6) Dual sensor with living detect, face recognition distance 0.3-3M,
(7) Face recognition within 500ms; Face library 22400 person. Total
storage 100,000 recognize record;
(8) Supporting SDK and HTTP protocols under Windows / Linux
(9) Device vision dynamics 80dB, suitable for backlight environment;
(10) Supports fog, 3D noise reduction, strong light suppression,
electronic image stabilization, multiple white balance modes.
(11) Linux operate system more stable.
1 Product Overview
Packing list of 7-inch or 8-inch turnstile
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 1*Hex screwdriver 6. 1*Gimbal bracket
7. 1*wall mount bracket 8. 1*Screw kits
Packing list of 7-inch or 8-inch wall-mounted
Face Recognition Terminal
User manual
Note
1. Device working temperature: 10 -40 Ć. Do not Install under the vent
and ensure that there is no heating source within 3 meters;
2. People entering the room from a cold outdoor environment will affect
measurement accuracy. The forehead temperature test needs to be
performed indoors without covering the forehead for three minutes and
the temperature is stable;
3. The temperature read by the temperature measuring device is the
temperature in the forehead area. When there is water, sweat, oil
orthick makeup on the forehead, or the elderly have wrinkles, the read
temperature will be lower than the actual temperature. Make sure there
is no hair or clothing covering this area.
-2--1-
1.3 Packing list
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 6* Tie 6. 1*Hex screwdriver
1.1 Introduction
The face recognition terminals are suitable for hotels, office buildings,
schools, shopping centers, KTV, bars, buses and communities.
1.2 Product Features
(1) Using high-precision infrared temperature detector non-contact
automatic body temperature detection;
(2) Temperature measurement range: 30-45 Ć, accuracy is ± 0.3
(3) Real-time output of identify results and voice prompts;
(4) Auto identify people without masks and sound real-time warning;
(5) Auto register and record information, avoid manual operation,
improve efficiency and reduce missing information;
(6) Dual sensor with living detect, face recognition distance 0.3-3M,
(7) Face recognition within 500ms; Face library 22400 person. Total
storage 100,000 recognize record;
(8) Supporting SDK and HTTP protocols under Windows / Linux
(9) Device vision dynamics 80dB, suitable for backlight environment;
(10) Supports fog, 3D noise reduction, strong light suppression,
electronic image stabilization, multiple white balance modes.
(11) Linux operate system more stable.
1 Product Overview
Packing list of 7-inch or 8-inch turnstile
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 1*Hex screwdriver 6. 1*Gimbal bracket
7. 1*wall mount bracket 8. 1*Screw kits
Packing list of 7-inch or 8-inch wall-mounted
Face Recognition Terminal
User manual
Note
1. Device working temperature: 10 -40 Ć. Do not Install under the vent
and ensure that there is no heating source within 3 meters;
2. People entering the room from a cold outdoor environment will affect
measurement accuracy. The forehead temperature test needs to be
performed indoors without covering the forehead for three minutes and
the temperature is stable;
3. The temperature read by the temperature measuring device is the
temperature in the forehead area. When there is water, sweat, oil
orthick makeup on the forehead, or the elderly have wrinkles, the read
temperature will be lower than the actual temperature. Make sure there
is no hair or clothing covering this area.
-2-
-1-
1.3 Packing list
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 6* Tie 6. 1*Hex screwdriver
1.1 Introduction
The face recognition terminals are suitable for hotels, office buildings,
schools, shopping centers, KTV, bars, buses and communities.
1.2 Product Features
(1) Using high-precision infrared temperature detector non-contact
automatic body temperature detection;
(2) Temperature measurement range: 30-45 Ć, accuracy is ± 0.3
(3) Real-time output of identify results and voice prompts;
(4) Auto identify people without masks and sound real-time warning;
(5) Auto register and record information, avoid manual operation,
improve efficiency and reduce missing information;
(6) Dual sensor with living detect, face recognition distance 0.3-3M,
(7) Face recognition within 500ms; Face library 22400 person. Total
storage 100,000 recognize record;
(8) Supporting SDK and HTTP protocols under Windows / Linux
(9) Device vision dynamics 80dB, suitable for backlight environment;
(10) Supports fog, 3D noise reduction, strong light suppression,
electronic image stabilization, multiple white balance modes.
(11) Linux operate system more stable.
1 Product Overview
Packing list of 7-inch or 8-inch turnstile
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*User manual 4. 1*Waterproof network head
5. 1*Hex screwdriver 6. 1*Gimbal bracket
7. 1*wall mount bracket 8. 1*Screw kits
Packing list of 7-inch or 8-inch wall-mounted
-3-
-4-
7-inch
wall-mounted
No. Description
J1
WG OutὉOrange D0njWhite D1njGreen GND
J2 RJ45 100M
DC
12V/3A
WG INὉBrown and white D0njYellow D1njGray GND
J3
Alarm outὉBrown Alarm+njPurple Alarm
RS485ὉOrange and White 485+njBlue and White 485
USBὉRed 5VnjBlue D-njGreen and white D+njBlack GND
3 Appearance
7-inch turnstile 8-inch turnstile 8-inch
wall-mounted
No. Name Description
J1 WG Out 1:D0 2:D1 3:GND
J2 WG IN NC
J3 Alarm Out Relay Switch
J4 USB USB Interface
J5 RJ45 100M
J6 DC12V 12V/3A
2 Specification
1. 7-inch turnstile
3. 8-inch turnstile
2. 7-inch wall-mounted
4. 8-inch wall-mounted
-3-
-4-
7-inch
wall-mounted
No. Description
J1
WG OutὉOrange D0njWhite D1njGreen GND
J2 RJ45 100M
DC
12V/3A
WG INὉBrown and white D0njYellow D1njGray GND
J3
Alarm outὉBrown Alarm+njPurple Alarm
RS485ὉOrange and White 485+njBlue and White 485
USBὉRed 5VnjBlue D-njGreen and white D+njBlack GND
3 Appearance
7-inch turnstile 8-inch turnstile 8-inch
wall-mounted
No. Name Description
J1 WG Out 1:D0 2:D1 3:GND
J2 WG IN NC
J3 Alarm Out Relay Switch
J4 USB USB Interface
J5 RJ45 100M
J6 DC12V 12V/3A
2 Specification
1. 7-inch turnstile
3. 8-inch turnstile
2. 7-inch wall-mounted
4. 8-inch wall-mounted
-5-
-6-
P
l
e
a
s
e
s
t
a
n
d
h
e
r
e
!
4.1 Adjust angle of temperature detector
After the temperature measurement access control is fully activated,
the human face is directly facing the device. Observe the face image
on the device screen. Make sure that the bare skin on the forehead is
placed in the "temperature measurement area" (optimal temperature
detector distance 0.5m). After that, paste the "Please stand here"
detection position mark at the corresponding distance.
4.3 Wall-mounted face recognition terminal
Attach the cable tie from the “Accessory Pack” to the tripod for the
temperature measurement access control on the column.
Turnstile face recognition terminal
Mount the gimbal bracket in the “Accessory Pack” to the tripod for the
wall-mounted temperature measurement access control. Connect the
power supply and network cable.
4.2 Temporary position
Note: Due to the height of the gate installation, it may cause the test
personnel to actively cooperate during the test to ensure that the bare
skin on the forehead is placed in the "temperature measurement area".
Real-Time Temperature Display
The detecting position
The comparison results
4 Installation
According to the device of the installation site, in the space position on
the gate or on the front side, the opening diameter of the 7-inch
turnstile is 30mm, and the opening diameter of the 8-inch turnstile is
35mm. The diagram is as follows:
The installation position
The detecting
position
Single channel gate Two channel gate
1.1~1.8meters 1.0meter 1.2meter0.6meter
Height
-5- -6-
P
l
e
a
s
e
s
t
a
n
d
h
e
r
e
!
4.1 Adjust angle of temperature detector
After the temperature measurement access control is fully activated,
the human face is directly facing the device. Observe the face image
on the device screen. Make sure that the bare skin on the forehead is
placed in the "temperature measurement area" (optimal temperature
detector distance 0.5m). After that, paste the "Please stand here"
detection position mark at the corresponding distance.
4.3 Wall-mounted face recognition terminal
Attach the cable tie from the “Accessory Pack” to the tripod for the
temperature measurement access control on the column.
Turnstile face recognition terminal
Mount the gimbal bracket in the “Accessory Pack” to the tripod for the
wall-mounted temperature measurement access control. Connect the
power supply and network cable.
4.2 Temporary position
Note: Due to the height of the gate installation, it may cause the test
personnel to actively cooperate during the test to ensure that the bare
skin on the forehead is placed in the "temperature measurement area".
Real-Time Temperature Display
The detecting position
The comparison results
4 Installation
According to the device of the installation site, in the space position on
the gate or on the front side, the opening diameter of the 7-inch
turnstile is 30mm, and the opening diameter of the 8-inch turnstile is
35mm. The diagram is as follows:
The installation position
The detecting
position
Single channel gate Two channel gate
1.1~1.8meters 1.0meter 1.2meter0.6meter
Height
-5- -6-
P
l
e
a
s
e
s
t
a
n
d
h
e
r
e
!
4.1 Adjust angle of temperature detector
After the temperature measurement access control is fully activated,
the human face is directly facing the device. Observe the face image
on the device screen. Make sure that the bare skin on the forehead is
placed in the "temperature measurement area" (optimal temperature
detector distance 0.5m). After that, paste the "Please stand here"
detection position mark at the corresponding distance.
4.3 Wall-mounted face recognition terminal
Attach the cable tie from the “Accessory Pack” to the tripod for the
temperature measurement access control on the column.
Turnstile face recognition terminal
Mount the gimbal bracket in the “Accessory Pack” to the tripod for the
wall-mounted temperature measurement access control. Connect the
power supply and network cable.
4.2 Temporary position
Note: Due to the height of the gate installation, it may cause the test
personnel to actively cooperate during the test to ensure that the bare
skin on the forehead is placed in the "temperature measurement area".
Real-Time Temperature Display
The detecting position
The comparison results
4 Installation
According to the device of the installation site, in the space position on
the gate or on the front side, the opening diameter of the 7-inch
turnstile is 30mm, and the opening diameter of the 8-inch turnstile is
35mm. The diagram is as follows:
The installation position
The detecting
position
Single channel gate Two channel gate
1.1~1.8meters 1.0meter 1.2meter0.6meter
Height
-5-
-6-
P
l
e
a
s
e
s
t
a
n
d
h
e
r
e
!
4.1 Adjust angle of temperature detector
After the temperature measurement access control is fully activated,
the human face is directly facing the device. Observe the face image
on the device screen. Make sure that the bare skin on the forehead is
placed in the "temperature measurement area" (optimal temperature
detector distance 0.5m). After that, paste the "Please stand here"
detection position mark at the corresponding distance.
4.3 Wall-mounted face recognition terminal
Attach the cable tie from the “Accessory Pack” to the tripod for the
temperature measurement access control on the column.
Turnstile face recognition terminal
Mount the gimbal bracket in the “Accessory Pack” to the tripod for the
wall-mounted temperature measurement access control. Connect the
power supply and network cable.
4.2 Temporary position
Note: Due to the height of the gate installation, it may cause the test
personnel to actively cooperate during the test to ensure that the bare
skin on the forehead is placed in the "temperature measurement area".
Real-Time Temperature Display
The detecting position
The comparison results
4 Installation
According to the device of the installation site, in the space position on
the gate or on the front side, the opening diameter of the 7-inch
turnstile is 30mm, and the opening diameter of the 8-inch turnstile is
35mm. The diagram is as follows:
The installation position
The detecting
position
Single channel gate Two channel gate
1.1~1.8meters 1.0meter 1.2meter0.6meter
Height
-7- -8-
5 Wall-mounted
Note: The installation height of 1.5 meters here is the recommended
installation height, and users can adjust it according to their height.
4.4 Adjust to best angle and detection position of the detector.
4.5 After temperature detect are confirmed , make detect position mark
on the ground for accurate detection.
Note: There is no need to move or adjust the relevant position or
height after installation is completed. Due to the height difference of
the inspected person, the inspected person may need to cooperate
actively to ensure the accuracy of the inspection data.
The installation position
The detecting
position
Installation with 86 boxes
Step 1: Make holes in the wall according to the mounting bracket and
install 86 boxes.
Step 2: Use a special tamper-proof wrench to loosen the tamper-resis-
tant fixing screws at the bottom of the device, remove the mounting
plate, and the hanging plate is fixed on the 86 box as shown below.
Step 3: Hang the device from top to bottom on the mounting plate.
Step 4: Use a special tamper wrench at the bottom of the device to
screw the tamper screws.
Installation without 86 boxes:
Step 1: Fix the mounting base on the mounting wall as shown in the
figure below.
Step 2: Use a special tamper-proof wrench to loosen the tamper-re-
sistant fixing screws at the bottom of the device, remove the mounting
plate, and lock it to the mounting base plate according to the hole
position.
Step 3: Hang the device from top to bottom on the mounting plate.
Step 4: Use a special tamper wrench at the bottom of the device to
lock the tamper screws.
-7- -8-
5 Wall-mounted
Note: The installation height of 1.5 meters here is the recommended
installation height, and users can adjust it according to their height.
4.4 Adjust to best angle and detection position of the detector.
4.5 After temperature detect are confirmed , make detect position mark
on the ground for accurate detection.
Note: There is no need to move or adjust the relevant position or
height after installation is completed. Due to the height difference of
the inspected person, the inspected person may need to cooperate
actively to ensure the accuracy of the inspection data.
The installation position
The detecting
position
Installation with 86 boxes
Step 1: Make holes in the wall according to the mounting bracket and
install 86 boxes.
Step 2: Use a special tamper-proof wrench to loosen the tamper-resis-
tant fixing screws at the bottom of the device, remove the mounting
plate, and the hanging plate is fixed on the 86 box as shown below.
Step 3: Hang the device from top to bottom on the mounting plate.
Step 4: Use a special tamper wrench at the bottom of the device to
screw the tamper screws.
Installation without 86 boxes:
Step 1: Fix the mounting base on the mounting wall as shown in the
figure below.
Step 2: Use a special tamper-proof wrench to loosen the tamper-re-
sistant fixing screws at the bottom of the device, remove the mounting
plate, and lock it to the mounting base plate according to the hole
position.
Step 3: Hang the device from top to bottom on the mounting plate.
Step 4: Use a special tamper wrench at the bottom of the device to
lock the tamper screws.
-9-
-10-
6 Setting & search on IE browser
6.1 Log in on the IE browser
After the face recognition machine is connected to the power supply
and the network cable, wait for about 2 minutes and the device will
finish booting.Enter the 192.168.1.88 on the IE browser, please enter
initial password: admin. Make sure the device and the computer are on
the same LAN, and the IP of the computer is 192.168.1.xx, if not,
please add an IP address of 192.168.1.xx.
6.2 Language change
Click System info to select the language interface you want. Check the
version information of the device
6.3 Change the password of the user
Click User Manage to change the password for select user.
6.5 LAN settings
User can change the LAN setting to user connect the device.
6.4 System Time
User can change the time of the device.
Login
User nameὉ
http://192.168.1.88/login.asp
Password:
admin
-9- -10-
6 Setting & search on IE browser
6.1 Log in on the IE browser
After the face recognition machine is connected to the power supply
and the network cable, wait for about 2 minutes and the device will
finish booting.Enter the 192.168.1.88 on the IE browser, please enter
initial password: admin. Make sure the device and the computer are on
the same LAN, and the IP of the computer is 192.168.1.xx, if not,
please add an IP address of 192.168.1.xx.
6.2 Language change
Click System info to select the language interface you want. Check the
version information of the device
6.3 Change the password of the user
Click User Manage to change the password for select user.
6.5 LAN settings
User can change the LAN setting to user connect the device.
6.4 System Time
User can change the time of the device.
Login
User nameὉ
http://192.168.1.88/login.asp
Password:
admin
-9- -10-
6 Setting & search on IE browser
6.1 Log in on the IE browser
After the face recognition machine is connected to the power supply
and the network cable, wait for about 2 minutes and the device will
finish booting.Enter the 192.168.1.88 on the IE browser, please enter
initial password: admin. Make sure the device and the computer are on
the same LAN, and the IP of the computer is 192.168.1.xx, if not,
please add an IP address of 192.168.1.xx.
6.2 Language change
Click System info to select the language interface you want. Check the
version information of the device
6.3 Change the password of the user
Click User Manage to change the password for select user.
6.5 LAN settings
User can change the LAN setting to user connect the device.
6.4 System Time
User can change the time of the device.
Login
User nameὉ
http://192.168.1.88/login.asp
Password:
admin
-9-
-10-
6 Setting & search on IE browser
6.1 Log in on the IE browser
After the face recognition machine is connected to the power supply
and the network cable, wait for about 2 minutes and the device will
finish booting.Enter the 192.168.1.88 on the IE browser, please enter
initial password: admin. Make sure the device and the computer are on
the same LAN, and the IP of the computer is 192.168.1.xx, if not,
please add an IP address of 192.168.1.xx.
6.2 Language change
Click System info to select the language interface you want. Check the
version information of the device
6.3 Change the password of the user
Click User Manage to change the password for select user.
6.5 LAN settings
User can change the LAN setting to user connect the device.
6.4 System Time
User can change the time of the device.
Login
User nameὉ
http://192.168.1.88/login.asp
Password:
admin
-11- -12-
6.6 Face recognise parameter setting
4. Snapmode
The access control device defaults is "single mode"
Single mode: used with “interval frames”, the default capture: 8 times,
and interval frames : 5 frames
5. Maximum and minimum pixels for face recognition
ŀThe maximum pixel setting range for face recognition: 300 ~ 500.
ŁFace recognition minimum pixel setting range: 30 ~ 300.
łWhen the pixels of the face in the picture are less than 150 (the
smallest pixels for face recognition), can’t capture;
6. Face scene
This parameter setting is used to adopt different face exposure
strategies for different application scenarios. There are two modes:
Conventional scene: used in normal environment;
lobby scene: suitable for backlight environment.
7. Face tracking
This parameter is used to overlay the face tracking .
8. Living detect
This parameter is used for living detect.
Note: Trial scene access control and gate. When multiple people pass
the gate, only the front one (the face pixel in the picture is the largest)
will be captured. According to the set interval frames, one face photo
will be captured and uploaded to the FTP server. There is only one
face frame in the picture.
2. Arming time
The user can set the two alarm time period.
3. Sensitivity
The setting range is 0 ~ 10. The sensitivity is higher that captured
picture will be poorer.
1. Enable
This item used to enable face recognition algorithm. Only when the
open, face recognise and capture can be performed;
Enable
Sensitivity
Capturetimes
FTPUpload
EveryNthFrame
Image Type
Face recogntion
maximun pixel
FaceQuality
Face test minimun
pixels
Human
Min pixel
Live detection
Face scene
FaceTrack
Snapmode
Function First
8
NO
5
Face Picture
500
99
300
Filter Tracking
200
Close
Lobby scene
Open
Single mode
Speed First
0 : 0 -- 23 : 59Time 1
9
ἷ1~100Ἰ
ἷ30~300Ἰ
ἷ0~500Ἰ
ἷ300~500Ἰ
ἷ1~1500Ἰ
Save
0 : 0 -- 23 : 59Time 2
-11-
-12-
6.6 Face recognise parameter setting
4. Snapmode
The access control device defaults is "single mode"
Single mode: used with “interval frames”, the default capture: 8 times,
and interval frames : 5 frames
5. Maximum and minimum pixels for face recognition
ŀThe maximum pixel setting range for face recognition: 300 ~ 500.
ŁFace recognition minimum pixel setting range: 30 ~ 300.
łWhen the pixels of the face in the picture are less than 150 (the
smallest pixels for face recognition), can’t capture;
6. Face scene
This parameter setting is used to adopt different face exposure
strategies for different application scenarios. There are two modes:
Conventional scene: used in normal environment;
lobby scene: suitable for backlight environment.
7. Face tracking
This parameter is used to overlay the face tracking .
8. Living detect
This parameter is used for living detect.
Note: Trial scene access control and gate. When multiple people pass
the gate, only the front one (the face pixel in the picture is the largest)
will be captured. According to the set interval frames, one face photo
will be captured and uploaded to the FTP server. There is only one
face frame in the picture.
2. Arming time
The user can set the two alarm time period.
3. Sensitivity
The setting range is 0 ~ 10. The sensitivity is higher that captured
picture will be poorer.
1. Enable
This item used to enable face recognition algorithm. Only when the
open, face recognise and capture can be performed;
Enable
Sensitivity
Capturetimes
FTPUpload
EveryNthFrame
Image Type
Face recogntion
maximun pixel
FaceQuality
Face test minimun
pixels
Human
Min pixel
Live detection
Face scene
FaceTrack
Snapmode
Function First
8
NO
5
Face Picture
500
99
300
Filter Tracking
200
Close
Lobby scene
Open
Single mode
Speed First
0 : 0 -- 23 : 59Time 1
9
ἷ1~100Ἰ
ἷ30~300Ἰ
ἷ0~500Ἰ
ἷ300~500Ἰ
ἷ1~1500Ἰ
Save
0 : 0 -- 23 : 59Time 2
-13-
-14-
6.7 Detection settings
1. Recognize mode
User can choose different recognize modes according to application,
1 Face detect 2 Temperature detect 3 Face detect+ Temperature detect;
Please ignore other recognize modes for these four devices.
2. Mask detect
You can choose the close or open for mask detection.
If the visitor does not wear a mask by if select opening, the device
will sound a warning prompt;
3. Temperature threshold
The temperature threshold can be set, and the default value is 37.3 Ć.
User can be adjust.
6.8 Access control
1. Weigand output
Weigand output include close, WG26, WG34
2. White light control
There are 4 light control modes. always on, time control, always off,
Turn off screen display after no one.
3. Screen display mode
There are 2 dispaly modes. Always display, Turn off screen display
after no one.
Note: The white light is controlled by motion detect.
When there is a motion detect, the white light is on.
After 10 seconds without alarm, the white light off and the screen off.
1.Celsius 2.Fahrenheit
Setting to <open> when detect wearing a mask.
6.9 RTSP, HTTP upload, FTP
Users can connect to NVR through RTSP settings.
Upload some information to the set HTTP address.
User can also upload some information to the set FTP address.
Temperature unit Celsius
Alarm Switch
Time 1 0 : 0 -- 23 : 59
0 : 0 -- 23 : 59
Time 2
Whitelist alarm VIP List Non-White list alarm
IO Output
Temperature
threshold
Close
37.3 (1-100)
Abnormal
temperature opens
the door
0.0 (0°-1°)
compensated temperature
Temperature
correction Intelligent Algorith
75 (1-100)
Open
60 (1-100)
Single recognize mode
Mask detect
Matching mode
ID similarity
Comparison
similarity
Alarm output 1 S
Recognize Mode
Type NO *
Temperature detect
Save Reply defaults
Continuous output
-13-
-13-
-14-
6.7 Detection settings
1. Recognize mode
User can choose different recognize modes according to application,
1 Face detect 2 Temperature detect 3 Face detect+ Temperature detect;
Please ignore other recognize modes for these four devices.
2. Mask detect
You can choose the close or open for mask detection.
If the visitor does not wear a mask by if select opening, the device
will sound a warning prompt;
3. Temperature threshold
The temperature threshold can be set, and the default value is 37.3 Ć.
User can be adjust.
6.8 Access control
1. Weigand output
Weigand output include close, WG26, WG34
2. White light control
There are 4 light control modes. always on, time control, always off,
Turn off screen display after no one.
3. Screen display mode
There are 2 dispaly modes. Always display, Turn off screen display
after no one.
Note: The white light is controlled by motion detect.
When there is a motion detect, the white light is on.
After 10 seconds without alarm, the white light off and the screen off.
1.Celsius 2.Fahrenheit
Setting to <open> when detect wearing a mask.
6.9 RTSP, HTTP upload, FTP
Users can connect to NVR through RTSP settings.
Upload some information to the set HTTP address.
User can also upload some information to the set FTP address.
Temperature unit Celsius
Alarm Switch
Time 1 0 : 0 -- 23 : 59
0 : 0 -- 23 : 59
Time 2
Whitelist alarm VIP List Non-White list alarm
IO Output
Temperature
threshold
Close
37.3 (1-100)
Abnormal
temperature opens
the door
0.0 (0°-1°)
compensated temperature
Temperature
correction Intelligent Algorith
75 (1-100)
Open
60 (1-100)
Single recognize mode
Mask detect
Matching mode
ID similarity
Comparison
similarity
Alarm output 1 S
Recognize Mode
Type NO *
Temperature detect
Save Reply defaults
Continuous output
-13-
-13-
-14-
6.7 Detection settings
1. Recognize mode
User can choose different recognize modes according to application,
1 Face detect 2 Temperature detect 3 Face detect+ Temperature detect;
Please ignore other recognize modes for these four devices.
2. Mask detect
You can choose the close or open for mask detection.
If the visitor does not wear a mask by if select opening, the device
will sound a warning prompt;
3. Temperature threshold
The temperature threshold can be set, and the default value is 37.3 Ć.
User can be adjust.
6.8 Access control
1. Weigand output
Weigand output include close, WG26, WG34
2. White light control
There are 4 light control modes. always on, time control, always off,
Turn off screen display after no one.
3. Screen display mode
There are 2 dispaly modes. Always display, Turn off screen display
after no one.
Note: The white light is controlled by motion detect.
When there is a motion detect, the white light is on.
After 10 seconds without alarm, the white light off and the screen off.
1.Celsius 2.Fahrenheit
Setting to <open> when detect wearing a mask.
6.9 RTSP, HTTP upload, FTP
Users can connect to NVR through RTSP settings.
Upload some information to the set HTTP address.
User can also upload some information to the set FTP address.
Temperature unit Celsius
Alarm Switch
Time 1 0 : 0 -- 23 : 59
0 : 0 -- 23 : 59
Time 2
Whitelist alarm VIP List Non-White list alarm
IO Output
Temperature
threshold
Close
37.3 (1-100)
Abnormal
temperature opens
the door
0.0 (0°-1°)
compensated temperature
Temperature
correction Intelligent Algorith
75 (1-100)
Open
60 (1-100)
Single recognize mode
Mask detect
Matching mode
ID similarity
Comparison
similarity
Alarm output 1 S
Recognize Mode
Type NO *
Temperature detect
Save Reply defaults
Continuous output
-13-
-13-
-14-
6.7 Detection settings
1. Recognize mode
User can choose different recognize modes according to application,
1 Face detect 2 Temperature detect 3 Face detect+ Temperature detect;
Please ignore other recognize modes for these four devices.
2. Mask detect
You can choose the close or open for mask detection.
If the visitor does not wear a mask by if select opening, the device
will sound a warning prompt;
3. Temperature threshold
The temperature threshold can be set, and the default value is 37.3 Ć.
User can be adjust.
6.8 Access control
1. Weigand output
Weigand output include close, WG26, WG34
2. White light control
There are 4 light control modes. always on, time control, always off,
Turn off screen display after no one.
3. Screen display mode
There are 2 dispaly modes. Always display, Turn off screen display
after no one.
Note: The white light is controlled by motion detect.
When there is a motion detect, the white light is on.
After 10 seconds without alarm, the white light off and the screen off.
1.Celsius 2.Fahrenheit
Setting to <open> when detect wearing a mask.
6.9 RTSP, HTTP upload, FTP
Users can connect to NVR through RTSP settings.
Upload some information to the set HTTP address.
User can also upload some information to the set FTP address.
Temperature unit Celsius
Alarm Switch
Time 1 0 : 0 -- 23 : 59
0 : 0 -- 23 : 59
Time 2
Whitelist alarm VIP List Non-White list alarm
IO Output
Temperature
threshold
Close
37.3 (1-100)
Abnormal
temperature opens
the door
0.0 (0°-1°)
compensated temperature
Temperature
correction Intelligent Algorith
75 (1-100)
Open
60 (1-100)
Single recognize mode
Mask detect
Matching mode
ID similarity
Comparison
similarity
Alarm output 1 S
Recognize Mode
Type NO *
Temperature detect
Save Reply defaults
Continuous output
-13-
-15- -16-
2. Click <Search> to check the attendance list.
6.10 List management & Attendance
1. Users can add lists or bulk import some information about employees.
3. Click <Search> to check the attendance list in the <Comparison>. You can view visitor information from the device, including whether the visitor is
wearing a mask, body temperature, and photos.
Pol. Ind. Sud-Oest C/Bernat de Rocaber, 16 Sabadell (Barcelona) 08205
Tel.: 93 721 97 55 e-mail: info@newgate.es
www.newgate.es
Table of contents
