Newport Brass 9911 User manual

I STALLATIO I STRUCTIO S
WIDE SPREAD KITCHE SET
MODEL O. 9911 & 9911L
Congratulations on the purchase
of your ewport Brass product,
an excellent choice, that will give you
years of quality service and enhance
the look and style of your home.

Recommended Installation by a Professional Plumbing Contractor
ote: The use of petroleum base plumbers putty on our products will nullify the warranty.
We recommend the use of clear silicone sealing materials. Recommended deck hole Ø1.25.
1.Thread flange UT (5) onto the diverter SHA K (4). Install from underside through center
hole of mounting surface. Place spout base RI G (2) with WASHER (3) over SHA K (4).
Thread SPOUT (1) onto end of SHA K (4). Secure into place with flange UT (5). See Figure
1.
2. Place UT (6) & WASHER (7) on valve BODY (8). Insert BODY (8), (blue cold and red hot),
through hole in the mounting surface. Adjust and secure with additional WASHER (7) and
UT (6) so that the top of valve is 2" above mounting surface. Before tightening down flange
UT (6), check HA DLE (21, 21a) alignment by placing onto Valve (8). Any adjustments for
rotational alignment must be made to the valve BODY (8), not to the cartridge. See Figure
1.
3. Insert vegetable spray HOSE (9) through BO ET (11) with O-RI G (10), ESCUTCHEO
(12) and mounting surface. From underside of mounting surface, insert HOSE (9) through
SHA K (13), threading into BO ET (11). Insert Hose (9) through MOUNTING KIT (14),
thread-ing onto SHA K (13) to secure in place. Attach other end of vegetable spray HOSE
(9) to base of diverter TEE (4). See Figure 2.
4. Connect large end of flexible HOSE (15) to side outlet of each valve BODY (8). Attach other
end of HOSE (15) to either side of the TEE (4). (Hand-tighten and secure each connection
with a wrench ¼ turn.) See Figure 3.
5. Connect hot/cold water supply to appropriate 1/2” PSM valve BODY (8), utilizing one of
the three following types of risers. Supply risers not included. See Figure 3.
a. 1/2” IPS flexible riser: discard rubber nosecone WASHER (16), friction WASHER (17) and
coupling UT (18).
b. 3/8” or 1/2” OD bullnose riser: utilize friction WASHER (17) and coupling UT (18).
c. 1/2” copper riser: utilize rubber nosecone WASHER (16), friction WASHER (17) and cou-
pling UT (18).
6.Thread ESCUTCHEO (19) and BO ET (20) onto valve. Any adjustments for rotational
alignment must be made to the valve body - not to the cartridge. ( ote: Allow minimum spac-
ing between HA DLE (21, 21a) and BO ET (20) to prevent damage to the surface finish.)
Attach HA DLE (21, 21a) and secure into place with SETSCREW (22). See Figure 4.
7. Remove AERATOR (23) from SPOUT (1), turn on water supply, and flush both valves until
water is clear. Check for leaks and make any final adjustments required. Re-attach AERATOR
(23) to the SPOUT (1).
WP-9911

Figure 1
Figure 4
Figure 3
Figure 2
2”
16
17
18
17
18
a
1
2
3
6
7
6
8
4
5
9
10
11
12
14
13
4
15
4
21a
21
19
20
22
[phone]
WP-9911 Santa Ana, CA 92705 01/23/2019
www.brasstech.com
b
c
EN-3558b Rev A