Nexcom Peak 779vl2 User manual

NEXCOM International Co., Ltd.

Published February 2020 www.nexcom.com

IoT Automation Solutions

PICMG Single Board Computer (PICMG 1.0)

PEAK 779VL2

User Manual

Content

Contents

Preface

Disclaimer.............................................................................................. iv

Acknowledgements ............................................................................... iv

Regulatory Compliance Statements........................................................ iv

Declaration of Conformity...................................................................... iv

RoHS Compliance ................................................................................... v

Warranty and RMA ................................................................................ vi

Safety Information ................................................................................viii

Installation Recommendations...............................................................viii

Safety Precautions.................................................................................. ix

Technical Support and Assistance............................................................ x

Conventions Used in this Manual............................................................ x

Global Service Contact Information........................................................ xi

Package Contents.................................................................................xiii

Ordering Information ............................................................................xiv

Chapter 1: Product Introduction

Overview ................................................................................................1

Key Features ...........................................................................................1

Hardware Specifications..........................................................................2

Knowing Your PEAK 779VL2...................................................................3

Chapter 2: Jumpers and Connectors

Before You Begin ....................................................................................4

Precautions ............................................................................................4

Jumper Settings ......................................................................................5

Locations of the Jumpers and Connectors...............................................6

Jumpers..................................................................................................7

CMOS Connector................................................................................7

AT/ATX Pin Header ..............................................................................7

ME Connector.....................................................................................8

Connector Pin Definitions .......................................................................9

External Connectors ............................................................................9

VGA Port .........................................................................................9

LAN1 Port ........................................................................................9

LAN2 Port ......................................................................................10

USB 3.0 Ports.................................................................................10

Internal Connectors...........................................................................11

USB 3.0 Box Header.......................................................................11

USB 2.0 Headers ............................................................................11

Keyboard and Mouse Connector....................................................12

+12V Power Connector..................................................................12

Smart FAN Connectors...................................................................13

Serial Port Box Headers ..................................................................13

RS422/RS485 Serial Port Box Header ..............................................14

2x8 Pin Header...............................................................................14

Content

SATA DOM Power Connector.........................................................15

IrDA Pin Header .............................................................................15

LAN LED Pin Header.......................................................................16

RI Pin Header .................................................................................16

Parallel Port Box Header .................................................................17

SATA 2.0 Connectors .....................................................................17

SATA 3.0 Connector.......................................................................18

DVI/HDMI/DP Port Connector.........................................................18

Audio Pin Header...........................................................................19

Standby Power Connector..............................................................19

Chapter 3: BIOS Setup

About BIOS Setup.................................................................................20

When to Configure the BIOS.................................................................20

Default Configuration...........................................................................21

Entering Setup......................................................................................21

Legends................................................................................................21

BIOS Setup Utility..................................................................................23

Main .................................................................................................23

Advanced..........................................................................................24

Chipset..............................................................................................34

Boot..................................................................................................38

Security .............................................................................................38

Save & Exit ........................................................................................39

Appendix A: Watchdog Timer

WDT Programming Guide.....................................................................40

Preface

PrefaCe

This publication, including all photographs, illustrations and software, is

part of this manual may be reproduced, copied, translated or transmitted in

any form or by any means without the prior written consent from NEXCOM

International Co., Ltd.

Disclaimer

The information in this document is subject to change without prior notice and

does not represent commitment from NEXCOM International Co., Ltd. However,

users may update their knowledge of any product in use by constantly checking

its manual posted on our website: http://www.nexcom.com. NEXCOM shall

not be liable for direct, indirect, special, incidental, or consequential damages

arising out of the use of any product, nor for any infringements upon the rights

of third parties, which may result from such use. Any implied warranties of

merchantability or fitness for any particular purpose is also disclaimed.

Acknowledgements

PEAK 779VL2 is a trademark of NEXCOM International Co., Ltd. All other

product names mentioned herein are registered trademarks of their

respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class A devices and

describes how to keep the system CE compliant.

Declaration of Conformity

FCC

This equipment has been tested and verified to comply with the limits for

a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference

to radio communications. Operation of this equipment in a residential area

(domestic environment) is likely to cause harmful interference, in which

case the user will be required to correct the interference (take adequate

measures) at their own expense.

The product(s) described in this manual complies with all applicable

European Union (CE) directives if it has a CE marking. For computer systems

to remain CE compliant, only CE-compliant parts may be used. Maintaining

CE compliance also requires proper cable and cabling techniques.

Preface

RoHS Compliance

NEXCOM RoHS Environmental Policy and Status

Update

NEXCOM is a global citizen for building the digital

infrastructure. We are committed to providing green

products and services, which are compliant with

European Union RoHS (Restriction on Use of Hazardous Substance in

Electronic Equipment) directive 2011/65/EU, to be your trusted green

partner and to protect our environment.

RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)

< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent

Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <

0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or

1,000ppm.

In order to meet the RoHS compliant directives, NEXCOM has established an

engineering and manufacturing task force in to implement the introduction

of green products. The task force will ensure that we follow the standard

NEXCOM development procedure and that all the new RoHS components

and new manufacturing processes maintain the highest industry quality

levels for which NEXCOM are renowned.

The model selection criteria will be based on market demand. Vendors and

suppliers will ensure that all designed components will be RoHS compliant.

How to recognize NEXCOM RoHS Products?

For existing products where there are non-RoHS and RoHS versions, the

suffix “(LF)” will be added to the compliant product name.

All new product models launched after January 2013 will be RoHS compliant.

They will use the usual NEXCOM naming convention.

Preface

Warranty and RMA

NEXCOM Warranty Period

NEXCOM manufactures products that are new or equivalent to new in

accordance with industry standard. NEXCOM warrants that products will

be free from defect in material and workmanship for 2 years, beginning on

the date of invoice by NEXCOM. HCP series products (Blade Server) which

are manufactured by NEXCOM are covered by a three year warranty period.

NEXCOM Return Merchandise Authorization (RMA)

▪Customers shall enclose the “NEXCOM RMA Service Form” with the

returned packages.

▪Customers must collect all the information about the problems

encountered and note anything abnormal or, print out any on-screen

messages, and describe the problems on the “NEXCOM RMA Service

Form” for the RMA number apply process.

▪Customers can send back the faulty products with or without accessories

(manuals, cable, etc.) and any components from the card, such as CPU

and RAM. If the components were suspected as part of the problems,

please note clearly which components are included. Otherwise, NEXCOM

is not responsible for the devices/parts.

▪Customers are responsible for the safe packaging of defective products,

making sure it is durable enough to be resistant against further damage

and deterioration during transportation. In case of damages occurred

during transportation, the repair is treated as “Out of Warranty.”

▪Any products returned by NEXCOM to other locations besides the

customers’ site will bear an extra charge and will be billed to the customer.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is

basic diagnostic fee and another is component (product) fee.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is

basic diagnostic fee and another is component (product) fee.

System Level

▪Component fee: NEXCOM will only charge for main components such as

SMD chip, BGA chip, etc. Passive components will be repaired for free,

ex: resistor, capacitor.

▪Items will be replaced with NEXCOM products if the original one cannot

be repaired. Ex: motherboard, power supply, etc.

▪Replace with 3rd party products if needed.

▪If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

Board Level

▪Component fee: NEXCOM will only charge for main components, such

as SMD chip, BGA chip, etc. Passive components will be repaired for free,

ex: resistors, capacitors.

▪If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

Preface

Warnings

Read and adhere to all warnings, cautions, and notices in this guide and

the documentation supplied with the chassis, power supply, and accessory

modules. If the instructions for the chassis and power supply are inconsistent

with these instructions or the instructions for accessory modules, contact

the supplier to find out how you can ensure that your computer meets

safety and regulatory requirements.

Cautions

Electrostatic discharge (ESD) can damage system components. Do the

described procedures only at an ESD workstation. If no such station is

available, you can provide some ESD protection by wearing an antistatic

wrist strap and attaching it to a metal part of the computer chassis.

Preface

Installation Recommendations

Ensure you have a stable, clean working environment. Dust and dirt can get

into components and cause a malfunction. Use containers to keep small

components separated.

Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow

require only a few simple tools, including the following:

▪A Philips screwdriver

▪A flat-tipped screwdriver

▪A grounding strap

▪An anti-static pad

Using your fingers can disconnect most of the connections. It is recommended

that you do not use needle-nose pliers to disconnect connections as these

can damage the soft metal or plastic parts of the connectors.

Safety Information

Before installing and using the device, note the following precautions:

▪Read all instructions carefully.

▪Do not place the unit on an unstable surface, cart, or stand.

▪Follow all warnings and cautions in this manual.

▪When replacing parts, ensure that your service technician uses parts

specified by the manufacturer.

▪Avoid using the system near water, in direct sunlight, or near a heating

device.

▪The load of the system unit does not solely rely for support from the

rackmounts located on the sides. Firm support from the bottom is highly

necessary in order to provide balance stability.

▪The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type recommended by the manufacturer.

Discard used batteries according to the manufacturer’s instructions.

Preface

Safety Precautions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect the equipment from any AC outlet before cleaning or installing

a component inside the chassis. Use a damp cloth. Do not use liquid or

spray detergents for cleaning.

4. To prevent electrostatic build-up, leave the board in its anti-static bag

until you are ready to install it.

5. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

6. Keep the board away from humidity.

7. Put the board on a stable surface. Dropping it or letting it fall may cause

damage.

8. Wear anti-static wrist strap.

9. Do all preparation work on a static-free surface.

10. Make sure the voltage of the power source is correct before

connecting the equipment to the power outlet.

11. Hold the board only by its edges. Be careful not to touch any of the

components, contacts or connections.

12. All cautions and warnings on the board should be noted.

13. Use the correct mounting screws and do not over tighten the screws.

14. Keep the original packaging and the anti-static bag; in case the board

has to be returned for repair or replacement.

Preface

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s

website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or

sales representative, please have the following information ready before

calling:

– Product name and serial number

– Detailed information of the peripheral devices

– Detailed information of the installed software (operating system,

version, application software, etc.)

– A complete description of the problem

– The exact wordings of the error messages

Warning!

1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products

or clean with a dry cloth.

3. CompactFlash: Turn off the unit’s power before inserting or removing a

CompactFlash storage card.

Conventions Used in this Manual

Warning:

Information about certain situations, which if not observed,

can cause personal injury. This will prevent injury to yourself

when performing a task.

CAUTION!

CAUTION!CAUTION! Caution:

Information to avoid damaging components or losing data.

Note:

Provides additional information to complete a task easily.

Preface

Global Service Contact Information

Headquarters

NEXCOM International Co., Ltd.

9F, No. 920, Chung-Cheng Rd.,

ZhongHe District, New Taipei City, 23586,

Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7782

www.nexcom.com

Asia

Taiwan

NexAIoT Co., Ltd.

Taipei Office

13F, No.920, Chung-Cheng Rd.,

ZhongHe District,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7796

Fax: +886-2-8226-7792

Email: [email protected]

www.nexcom.com.tw

NexAIoT Co., Ltd.

Taichung Office

16F, No.250, Sec. 2, Chongde Rd.,

Beitun Dist.,

Taichung City 406, R.O.C.

Tel: +886-4-2249-1179

Fax: +886-4-2249-1172

Email: [email protected]

www.nexcom.com.tw

NexCOBOT Taiwan Co., Ltd.

13F, No.916, Chung-Cheng Rd.,

ZhongHe District,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7796

Fax: +886-2-8226-7792

Email: [email protected]

www.nexcom.com.tw

GreenBase Technology Corp.

13F, No.922,Chung-Cheng Rd.,

Zhonghe Dist.,

New Taipei City, 23586, Taiwan, R.O.C.

Tel: +886-2-8226-7786

Fax: +886-2-8226-7900

Email:[email protected]

www.nexcom.com.tw

China

NEXSEC Incorporated

Floor 5, No.4, No.7 fengxian middle Rd.,

(Beike Industrial Park), Haidian District,

Beijing, 100094, China

Tel: +86-10-5704-2680

Fax: +86-10-5704-2681

Email: [email protected]

www.nexcom.cn

Preface

NEXGOL

1st Floor, Building B4, Electronic 2nd Area,

(Phoenix Lake Industrial Park), Yongchuan Dist.,

Chongqing City, 402160, China

Tel: +86-23-4960-9080

Fax: +86-23-4966-5855

Email: [email protected]

www.nexgol.com/NexGoL

Beijing NexGemo Technology Co.,Ltd.

5th Floor, Gemotech Building, No.1, Development Rd.,

Changping International Information Industry Base,

Changping District,

Beijing,102206, China

Tel: +86-10-8190-9399

Fax:+86-10-8190-9456

Japan

NEXCOM Japan

9F, Tamachi Hara Bldg.,

4-11-5, Shiba Minato-ku,

Tokyo, 108-0014, Japan

Tel: +81-3-5419-7830

Fax: +81-3-5419-7832

Email: [email protected]

www.nexcom-jp.com

NEXCOM Shanghai

Room 603/604, Huiyinmingzun Plaza Bldg., 1,

No. 609, Yunlin East Rd.,

Shanghai, 200062, China

Tel: +86-21-5278-5868

Fax: +86-21-3251-6358

Email: [email protected]

www.nexcom.cn

NEXCOM Surveillance Technology Corp.

Floor 5, Building C, ZhenHan Industrial Zone,

GanKeng Community, Buji Street,

LongGang District,

ShenZhen, 518112, China

Tel: +86-755-8364-7768

Fax: +86-755-8364-7738

Email: [email protected]

www.nexcom.cn

NEXCOM United System Service

Room 603/604, Huiyinmingzun Plaza Bldg. 1,

No. 609, Yunlin East Rd.,

Shanghai, 200062, China

Tel: +86-21-5278-5868

Fax: +86-21-3251-6358

Email: [email protected]

www.nexcom.cn

Europe

United Kingdom

NEXCOM EUROPE

10 Vincent Avenue,

Crownhill Business Centre,

Milton Keynes, Buckinghamshire

MK8 0AB, United Kingdom

Tel: +44-1908-267121

Fax: +44-1908-262042

Email: [email protected]

www.nexcom.eu

America

USA

NEXCOM USA

2883 Bayview Drive,

Fremont CA 94538, USA

Tel: +1-510-656-2248

Fax: +1-510-656-2158

Email: [email protected]

www.nexcom.com

Preface

Package Contents

Before continuing, verify that the PEAK 779VL2 package that you received is

complete. Your package should have all the items listed in the following table.

Item Name Qty

1 PEAK 779VL2 Serial Motherboard 1

2 Print 25 to 2.0mm 26-pin PIT:1.0mm L:260mm w/Bracket 1

3COM Port. 9-pin to Housing 10-pin PIT:2.0mm x 2

L:150mm+-10mm 1

4 SATA Cable ACMELUX:19922413 Standard L:300mm 1

5 USB CON x 2 + Bracket to JST 6-pin 2.5mm L:240+-15mm 1

6PS2 Y Cable CONNTEK:A02-A052-V01 PS2 to JST 6P

PH:2.0 L=250mm 1

7 PEAK 779VL2 Quick Reference Guide VER:A SIZE:A4 1

8 PEAK 779VL2 DVD Driver VER:1.0 1

9Cable EDI:358203030501-RS JST 3-pin to 3-pin 2.5mm

Twisting Wire L:500mm 1

Preface

Ordering Information

The information below provides ordering information for PEAK 779VL2.

PEAK 779VL2 (P/N: 10P0779VL00X0)

PICMG 1.0 full-size SBC, Intel®B75 chipset, 3rd generation Intel®Core™

i7/i5/i3 processor with DDR3 DIMM 1333/1600MHz up to 16G, VGA

integrated, 2 x GbE, 4 x SATA

Chapter 1: Product Introduction

ChaPter 1: ProduCt IntroduCtIon

Key Features

▪Scalable platform 3rd generation Intel®Core™ i7/i5/i3 processors + non-

ECC

▪Intel®B75 PCH chipset support PICMG1.0 specification

▪Support dual channel DDR3 with non-ECC DIMMs 1333/1600MHz, up

to 16GB

▪Support PCI/ISA, 4 x USB 3.0/4 x USB 2.0, 1 x SATA 3.0/3 x SATA 2.0 and

2 x GbE

▪Display support for VGA, DVI, HDMI

▪Dimension 338.58mm (L) x 122mm (W) (8 layers single side)

Overview

Chapter 1: Product Introduction

Hardware Specifications

CPU Support

▪Support Intel®LGA1155, 3rd generation Intel®Core™ processor

▪Intel®Core i7-3770 (4C/8M cache/3.4GHz/Max. TDP 77W)

▪Intel®Core i5-3550S (4C/6M cache/3.0GHz/Max. TDP 65W)

▪Intel®Core i3-3220 (2C/3M cache/2.4GHz/Max. TDP 55W)

▪Intel®Pentium®G2120 (2C/3M cache/1.6GHz/Max. TDP 65W)

Main Memory

▪Dual DDR3/DIMMs, support 1333/1600MHz non-ECC system memory

up to 16GB

Platform Control Hub

▪Intel®B75 PCH chipset

BIOS

▪AMI System BIOS

▪Plug and play support

▪Advanced power management and advanced configuration & power

Display

▪Intel®HD graphics with DX11 support up to two independent displays

▪Supports VGA and DVI/HDMI interfaces

Audio

▪HDA interface with pin header

Onboard LAN

▪Intel®82579LM Gigabit Ethernet

▪Intel®82574l Gigabit Ethernet

▪Support PXE boot from LAN, wake on LAN function

I/O Interface

▪USB 3.0: 2 x ports through I/O bracket/2 x ports through JST connector

▪USB 2.0: 4 x ports through 2.5mm JST connectors

▪Four SATA ports: one SATA 3.0/three SATA 2.0

▪Four PCI interfaces/three ISA interfaces (through ITE8888)

▪Two RJ45 Gigabit Ethernet LAN ports

▪Four serial ports (COM2 supports RS232/422/485, RI pin can supply 5V/12V

voltage)

▪Parallel port through box header

▪Keyboard/mouse interface

▪HDA interface through pin header for audio function (optional)

Power Requirements

▪+12V, +5V, +3.3V, +5VSB, +3.3V RTC power

▪Power source from backplane through golden finger and AUX +12V

▪Support ATX/AT power supplies

Dimensions

▪338.58mm (L) x 122mm (W)

Environment

▪Board level operating temperatures: -15°C to 60°C

▪Storage temperatures: -20°C to 80°C

▪Relative humidity:

10% to 90% (operating, non-condensing)

5% to 95% (non-operating, non-condensing)

Certifications

▪Meet CE

▪FCC Class A

Chapter 1: Product Introduction

Knowing Your PEAK 779VL2

IrDA

LPT Audio

COM4

COM2

COM3

COM1

USB 3.0

LAN

VGA

LAN LED

DVI/HDMI/DP Standby

Power

SATA DOM

Power

CMOS

Clear

AT/ATX

Select

RI KB/MS

SATA2 x 2

SATA2

SATA3 Front Panel

USB 3.0

USB 2.0 x 2

DIMM2 DIMM1 FANFAN ATX-4P

Chapter 2: Jumpers and Connectors

ChaPter 2: JumPers and ConneCtors

This chapter describes how to set the jumpers and connectors on the

PEAK 779VL2 motherboard.

Before You Begin

▪Ensure you have a stable, clean working environment. Dust and dirt can

get into components and cause a malfunction. Use containers to keep

small components separated.

▪Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow

require only a few simple tools, including the following:

– A Philips screwdriver

– A flat-tipped screwdriver

– A set of jewelers screwdrivers

– A grounding strap

– An anti-static pad

▪Using your fingers can disconnect most of the connections. It is

recommended that you do not use needle-nosed pliers to disconnect

connections as these can damage the soft metal or plastic parts of the

connectors.

▪Before working on internal components, make sure that the power is off.

Ground yourself before touching any internal components, by touching

a metal object. Static electricity can damage many of the electronic

components. Humid environments tend to have less static electricity than

dry environments. A grounding strap is warranted whenever danger of

static electricity exists.

Precautions

Computer components and electronic circuit boards can be damaged by

discharges of static electricity. Working on computers that are still connected

to a power supply can be extremely dangerous.

Follow the guidelines below to avoid damage to your computer or yourself:

▪Always disconnect the unit from the power outlet whenever you are

working inside the case.

▪If possible, wear a grounded wrist strap when you are working inside the

computer case. Alternatively, discharge any static electricity by touching

the bare metal chassis of the unit case, or the bare metal body of any

other grounded appliance.

▪Hold electronic circuit boards by the edges only. Do not touch the

components on the board unless it is necessary to do so. Don’t flex or

stress the circuit board.

▪Leave all components inside the static-proof packaging that they shipped

with until they are ready for installation.

▪Use correct screws and do not over tighten screws.

Chapter 2: Jumpers and Connectors

Jumper Settings

A jumper is the simplest kind of electric switch. It consists of two metal

pins and a cap. When setting the jumpers, ensure that the jumper caps are

placed on the correct pins. When the jumper cap is placed on both pins, the

jumper is short. If you remove the jumper cap, or place the jumper cap on

just one pin, the jumper is open.

Refer to the illustrations below for examples of what the 2-pin and 3-pin

jumpers look like when they are short (on) and open (off).

Two-Pin Jumpers: Open (Left) and Short (Right)

Three-Pin Jumpers: Pins 1 and 2 are Short

Chapter 2: Jumpers and Connectors

Locations of the Jumpers and Connectors

The figure below shows the location of the jumpers and connectors for PEAK 779VL2.

291

302

A62 J9

240

120

121

240

120

121

36 3334 32

35 31 26

2930 21

25 2324

20 18

17 15

14 10

11 9

85674321

AFAG

BAT1

128

BZ1

C313

C280

R360

R353

R2R1 C24C6 C7 C8 C10C9

JP6

DIMM2

DIMM1

CON1

FAN1

FAN2

J1 CN13

CN4

CN1 CN3 CN2 JP1

CN6

CN9

CN10

LAN1

LAN2

JP8

JP7

CN12 J11

JP9

VGA1

CN11

JP2

JP3

JP4

JP5

CN5

CN8

CN7

Table of contents

Other Nexcom Motherboard manuals

Popular Motherboard manuals by other brands

Gigabyte

Gigabyte B660 AORUS MASTER user manual

Texas Instruments

Texas Instruments TPS54202HEVM-716 user guide

VIA Technologies

VIA Technologies EPIA-M10000G - VIA Motherboard - Mini ITX user manual

Supermicro

Supermicro H12SSW-AN6 user manual

Aaeon

Aaeon Gene-4310 user manual

ON Semiconductor

ON Semiconductor FUSB251 user manual

Analog Devices

Analog Devices AD8450-EVALZ user guide

MSI

MSI B450M MORTAR TITANIUM quick start

VIA Technologies

VIA Technologies EPIA-M900 user manual

SOYO

SOYO 82430 HX User's guide & technical reference

DFI

DFI K6BV3+/66 user manual

TYAN

TYAN Thunder n4250QE-S4985G3NR-E manual 

Gigabyte

Gigabyte GA-K8NMF-9 user manual

Commell

Commell AS-C7A user manual

ASROCK

ASROCK A780GXH-128M installation guide

Texas Instruments

Texas Instruments TPS65994 EVM user guide

Biostar

Biostar Racing X470GTN manual

ECS

ECS H61H-G11 manual

Nexcom PEAK 779VL2 User manual

Popular Motherboard manuals by other brands