Next 427044 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
PRODUCT INFORMATION
• Do not use abrasive cleaning products or those containing silicone.
• Made in China.
•
A mattress measuring 135cm x 190cm is intended for use with this bed.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• We suggest you spend a short time reading through this leaet and then follow the simple step by step instructions.
• Carefully check that you have all parts before beginning assembly.
• Keep ttings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• A minimum of 2 adults is required to assemble this product.
• All assembly xings should always be tightened properly and periodically check all xings and tighten if necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the oor as this will cause damage to the joints.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
427044 PRIMROSE METAL BED - DOUBLE
Page 1 of 5

1. Insert 14 x slats 7 into the slat holes of the strap
assembly 10. Ensure the curve of the slats are facing
upwards.
FITTINGS
STEP ONE
PARTS
Page 2 of 5

1. Insert 28 x plastic end caps 9 onto one edge of
each wooden slat assembly. Ensure the curves of the
slats are facing upwards and the pins of the caps
facing downwards.
1. Attach 2 x side rails 3 to headboard 1 and
footboard 2 with 8 x bolts (A), 8 x washers (E) and 8 x
rubber washers (F), using allen key (I) to tighten.
1. Attach 2 x support rails 5 to centre rail 4 using 4 x
bolts (C) and 4 x washers (E), using allen key (I) to
tighten.
STEP TWO
STEP THREE
STEP FOUR
Page 3 of 5

1. Attach 2 x adjustable feet (G) into support legs 6.
2. Attach 2 x support legs 6 to centre rail 4 using 2 x
bolts (C) and 2 x washers (E), using allen key (I) to
tighten.
3. Attach support rails 5 to side rails 3 with 4 x bolts
(B), 8 x washers (E) and 4 x nuts (D), using allen key
(I) to tighten.
1. Attach 14 x slat centre caps 8 onto the ends of the
slat assembly already part assembled. Firmly press in
place the caps into the holes in the side and centre
rails. Ensure the curve of the slats face upwards.
2. Ensure the ends of the straps are wrapped around
support rails 5 tightly.
IMPORTANT: Once the feet (part H) have been
assembled and attached they should be adjusted to
ensure they do not touch the floor (5mm above floor)
to allow for movement once the mattress is placed on
the bed frame.
It is important to note that when moving the bed
ensure that it is not dragged into its new position to
prevent the possibility of these feet being twisted or
angled to one side which could lead to the collapse
of th centre of the bed.
Remove the mattress and lift the bed into its new
position to aviod damaging the bed. Ensure the feet
are at 90۫ to the floor before replacing the mattress.
STEP FIVE
STEP SEVEN
STEP SIX
Page 4 of 5

Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SEVEN
Page 5 of 5