Next 877740 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
•Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
•Never drag pieces of furniture across the floor as this will cause damage to the joints.
ASSEMBLY INSTRUCTIONS.
IMPORTANT
•We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
•Carefully check that you have all parts before beginning assembly.
•Keep fittings out of children's reach and keep children well away from the construction area.
•We recommend that the packaging is used to protect the surfaces during assembly.
•Do not put hot dished directly on the surfaces of the item.
•Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
PRODUCT INFORMATION
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Made in China.
• Do not use this item if any structual part is broken or missing.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be fault
y
. Should
y
ou need to return the unassembled
p
roduct
, p
lease re
p
ack in the ori
g
inal
p
acka
g
in
g
.
•Made fro metal base, MDF and solid wood with a painted finish.m
CARE INSTRUCTIONS
•A minimum of 2persons is required to assemble this product.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• All assembly fittings should always be tightened properly.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Do not use abrasive cleaning products or those containing silicone.
•Gloss finishes are prone to light surface scratch and it is therefore very important that you care for this item
correctly.
• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft
cloths (including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try
your cloth in an inconspicuous area of the furniture first to assess its suitability.
•Do not rub or scrub the surface when cleaning.
•Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
877740 GLOSS TURNED TABLE
Page 1 of 8
• Please remove the plastic protection film on the table top before use.
or damage.

Page 2 of 8
FITTINGS
A x 4 C x 3
D x 1
H x 3 I x 1
(M6x29mm) (M8x93mm)
(M10x90mm)
E x 3
( 12.5)
F x 1
( 16.5)
J x 1 K x 1 L x 1
( 17) ( 20) (M4) (M6) (M8)
G x 8
( 16)
B x 4
(M6x39mm)
PARTS
1 Table top support x 1
2 Base x 1
3 Base support x 1
4 Table top x 1 5 Pillar x 1
Ø1 Ø
Ø Ø (Ø
(Pre-assembled with table top 4
)(Pre-assembled with base )
2
(Pre-assembled with base )
2
(Pre-assembled
with table top
4
)

1. Remove 3 nuts and paper board from 3 x bolts (C) which attached on base (2),
However please do not pull out bolt (C) because bolt (C) also aim as position locator.
: Please do not pull out bolts (C)
STEP ONE
Page 3 of 8
2
3
2
3
CEH
H
C
E
HEC
Z
Z
Z
Z
N.B.

1. Attach base support (3) and base (2) to pillar (5) by fasten 3 x bolts (C).
2. Attach 1 x bolt (D) ,1 x spring washer (F) and 1 x washer (I) to the
assembled unit and tighten by using allen key (L).
STEP TWO
Page 4 of 8
3
5
D
F
I2
C
E
H
C
E
H
H
C
E
Z
Z
F
I
D

.1. Place the table top (4) upside down onto the foam.
2. Screw out 4 x bolts (A) from table top (4) and pull out 4 x washers (G)
from table top (4) by the use of allen key (J)
Keep all 4 x bolts (A) & 4 x washers (G) because these will be use for later step.
STEP THREE
Page 5 of 8
N.B:
G
A
G
1
4
4
1
A
AA
A
G
A
A
A
G
Foam
Foam

STEP FOUR
Page 6 of 8
1. Attach table top support (1) to the assembled unit with 4 x bolts (B) & 4 x washers (G) and tighten by using
allen key (J).
B
B
B
BG
G
G
1
5
2
G

1. Attach table top (4) to the assembled unit with 4 x bolts (A) & 4 x washers (G) and tighten by using allen key (J).
STEP FIVE
Page 7 of 8
G
A
G
A
A
G
A
G
4
5
1
Foam
Z
Z
B
B
1
N.B.:Please place the foam under the table top for protection purpose.

Page 8 of 8
STEP SIX
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
1. Upside down the table to correct position and remove the plastic protection film on top.