Next ASHTON 863677 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Do not rub or scrub the surface when cleaning.
CARE INSTRUCTIONS
• Do not put hot dishes directly on the surfaces of the item.
• For general cleaning, periodically dust with a soft cloth.
• Made from MDF with a painted finish.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Carefully check that you have all parts before beginning assembly.
• Made in China.
• Not suitable for use in bathrooms.
PRODUCT INFORMATION
863677 ASHTON HALL SEAT
Page1of4

1. Insert 2 x cambolts (A) and 2 x wooden dowels
(C) to top side panels 6 (both L&R).
2. Attach top side panel 6 (both L&R) to top back
panel 5.
3. Insert 2 x camlocks (B) to top back panel 5.
Ensure the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
1. Insert 6 x wooden dowels (C) to top panel 1.
2. Attach top panel 1 to assembled unit with 7 x
screws (D) and tighten.
STEP TWO
PARTS
FITTINGS
STEP ONE
Page2of4

1. Insert 6 x cambolts (A) and 6 x wooden dowels
(C) to top panel 1.
2. Attach the middle divider panel 4 and side panel
2 (both L&R) to assembled unit.
3. Insert 6 x camlocks (B) to the divider panel 4
and side panel 2 (both L&R). Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 6 x wooden dowels (C) to the bottom
panel 3.
2. Attach bottom 3 panel to the assembled unit
with 6 x screws (D) and tighten with a
screwdriver.
1. Attach back panel 7 to the assembled unit with
15 x screws (E) and tighten with a screwdriver.
STEP THREE
STEP FOUR
STEP FIVE
Page3of4

1. Insert 2 x PE baskets 9 into the unit.
2. Place the seat pad onto the unit.
1. Use screw (C) and washer (B) to secure the
nylon strap (A) to the top panel.
2. Secure the other end of the strap to the wall
with an appropriate screw and wall plug for your
wall type. To hide the strap behind the unit, drill
the holes lower than the top of unit.
Warning : Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB : Wall fixings are not included-please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SEVEN
STEP SIX
Page4of4