Next DOLLSHOUSE 888714 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
CARE INSTRUCTIONS
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Not suitable for use in bathrooms.
PRODUCT INFORMATION
• Made from MDF with a painted finish.
• Made in China.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not rub or scrub the surface when cleaning.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Do not put hot dishes directly on the surfaces of the item.
• For general cleaning, periodically dust with a soft cloth.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
888714 DOLLSHOUSE BOOKCASE
Page1of5

1. Insert 2 x cambolts (A) into shelf panel 4.
2. Attach divider panel 6 to shelf panel 4.
3. Insert 2 x camlocks (B) into divider panel 6.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
4. Attach shelf panel 5 to divider panel 6 with 2 x
screws (E), tighten with a screwdriver.
1. Insert 2 x cambolts (A) into shelf panel 5.
2. Attach divider panel 6 to shelf panel 5.
3. Insert 2 x camlocks (B) into divider panel 6.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
4. Attach shelf panel 10 to divider panel 6 with 2
x screws (E), tighten with a screwdriver.
1. Insert 2 x cambolts (A) into shelf panel 10.
2. Attach divider panel 6 to shelf panel 10.
3. Insert 2 x camlocks (B) into divider panel 6.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
STEP ONE
FITTINGS
STEP TWO
PARTS
STEP THREE
C x 4
(9) Back Panel x 1
Page2of5

1. Insert 6 x cambolts (A) into side panel 2-R.
2. Attach side panel 2-R to the assembled unit .
3. Insert 6 x camlocks (B) into shelf panel 4,shelf
panel 5 and shelf panel 10. Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 6 x cambolts (A) into side panel 2-L .
2. Attach side panel 2-L to the assembled unit .
3. Insert 6 x camlocks (B) into shelf panel 4,shelf
panel 5 and shelf panel 10. Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 4 x wooden dowels (C) into side panels
2 (both L&R).
2. Attach bottom panel 3 to the assembled unit
with 6 x screws (E) and tighten with a
screwdriver.
1. Insert 2 x cambolts F to top panel 1-L
2. Fix 2 x cambolts F to top panel 1-L with 2 x
camlocks . Ensure the arrow indicator is
pointing towards the panel edge before
tightening with a screwdriver.
1. Insert 2 x cambolts F pre-fitted in Step Eight
to top panel 1-R.
2. Insert 2 x camlocks (B) into top panel 1-R .
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
STEP SIX
STEP FOUR
STEP FIVE
STEP SEVEN
STEP EIGHT
Page3of5

1. Insert back panel 7 into the grooves of top
panel 1 (both L&R).
1. Attach back panel 7 to the assembled unit
with 2 x screws (D) and tighten.
1. Attach top panel 1 (both L&R) to the
assembled unit with 4 x screws (E) and tighten.
1. Attach back panel 8(x2) and back panel 9 to
the assembled unit with 26 x screws (D) and
tighten.
STEP TEN
STEP ELEVEN
STEP NINE
STEP TWELVE
Page4of5

1.Use screw (J) and washer (H) to secure the
nylon strap (G) to the top panel
.
2.Secure the other end of the strap to the wall
with an appropriate screw and wall plug for your
wall type. To hide the strap behind the unit, drill
the holes lower than the top of unit.
Warning :Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB:Wall fixings are not included-please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
PACKAGING LAYOUT
STEP THIRTEEN
Page5of5