Next HIGHBURY 872404 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
872404 HIGHBURY CHEST
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Do not put hot dishes directly on the surfaces of the item.
• For general cleaning, periodically dust with a soft cloth.
PRODUCT INFORMATION
• Made from Pine with lacquer finish.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Do not rub or scrub the surface when cleaning.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
CARE INSTRUCTIONS
• Natural features ensure that each piece is individual. Every effort is made to ensure colour continuity between
pieces, however this is a natural product, slight colour variations and natural grain markings may occur.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Made in China.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten i
f
necessary.
Page 1 of 8

PARTS
FITTINGS
(75×18×0.3mm)
A×34 B×34 C×4 D×4
1×1 2×1 3×1
4×3 5×4 6×2 7×2 8×2 9×2
Page 2 of 8

1. Insert 18 x cambolts (A) to panel 2 & panel 3, and
tighten with a screwdriver.
2. Insert 4 x wood dowels(E) & 8 x wood dowels (F)
on panel 2 & panel 3.
3. Insert 6 x wood dowel (E) to 3 x rails 17.
4. Insert 6 x wood dowel (E) to 3 x rails 18.
5. Insert 2 x wood dowel (E) to rail 19.
6. Insert 8 x cambolt (A) and 2 x cambolot (C ) to 2 x
panel 6, tighten with a screwdriver.
7. Insert 8 x cambolt (A) and 2 x cambolot (C ) to 2 x
panel 10, tighten with a screwdriver.
8. Insert 4 x wood dowel (E) to 2 x panel 12.
9. Insert 4 x wood dowel (E) to 2 x panel 13.
STEP ONE
2
3
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
E
EE
E
E
E
F
F
F
19
6×2
13×2
A
A
AA
AA
AA
EE
E
EE
E
E
C
C
E
Page 3 of 8

1. Attach panel 2 to panel 20 by 3 x screws (G),
tighten with a screwdriver.
1. Attach panel 3 to panel 20 by 3 x screws (G),
tighten with a screwdriver.
STEP FOUR
STEP THREE
STEP TWO
20
20
1. Attach panel 19 to panel 21 by 4 x screws (G),
tighten with a screwdriver.
1. Attach rail 15,16, 3x17, 3x18 & rail 21 to panel 2
2. Insert 9 x camlock (B) into rail 15,16, 3x17, 3x18 &
rail 21 and tighten with a screwdriver.
Ensure the arrow indicators on the camlocks are
pointing towards the panel edges and ensure the
assembly bolts locate properly into the camlocks
before turning clockwise with a screwdriver to
STEP
FOUR
STEP FIVE
21
B
B
B
B
B
B
B
B
B
2
21
18
18
18
17
17
17
2
Page 4 of 8

1. Attach panel 3 onto assembled unit.
2. Insert 9 x camlock (B) into rail 15,16, 3x17, 3x18 &
rail 21 and tighten with a screwdriver.
Ensure the arrow indicators on the camlocks are
pointing towards the panel edges and ensure the
assembly bolts locate properly into the camlocks
before turning clockwise with a screwdriver to
1. Stand up assembled unit.
2. Attach panel 1 onto assembled unit by 10 x screws
(G), tighten with a screwdriver.
STEP SEVEN
STEP SIX
B
B
B
B
B
B
B
B
B
3
1. Attach 3 x back panels 4 on back of assembled
unit by 42 x screws (H), tighten with a screwdriver.
STEP EIGHT
H×42
4
4
4
Page 5 of 8

1. Attach 1 x wall attachment strap (O) to the back of
the top panel with 1 x washer (M) and 1 x screw (N).
1. Attach panel 8,9 & 14 to panel 6.
2 I t4 l k(B)t l8&9 ti ht ith
STEP TEN
STEP NINE
M
2
.
I
nsert
4
x cam
l
oc
k(B)
to pane
l
8&9
, t
i
g
h
ten w
i
t
h
a
screwdriver.
3. Insert 1 x camlock(D) to panel 14, tighten with a
screwdriver.
Ensure the arrow indicators on the camlocks are
pointing towards the panel edges and ensure the
assembly bolts locate properly into the camlocks
before turning clockwise with a screwdriver to
4. Slide panel 5 into groove of assembled unit.
5. Attach panel 7 to assembled unit and secured by 6
x screws (G), tighten with a screwdriver.
6. Attach 2 x handles (I) to front panel 6 and secured
by 4 x screws (J), tighten with a screwdriver.
7. Repeat above steps to assembled another drawer.
DB×2
B×2
7
8
9
14
G×2
G×2
G×2
×2
Page 6 of 8

1. Attach panel 12,13 & 14 to panel 10.
2. Insert 4 x camlock(B) to panel 12&13, tighten with
a screwdriver.
3. Insert 1 x camlock(D) to panel 14, tighten with a
screwdriver.
Ensure the arrow indicators on the camlocks are
pointing towards the panel edges and ensure the
assembly bolts locate properly into the camlocks
before turning clockwise with a screwdriver to
tighten.
4. Slide panel 5 into groove of assembled unit.
5. Attach panel 11 to assembled unit and secured by
8 x screws (G), tighten with a screwdriver.
6. Attach 2 x handles (I) to front panel 10 and
secured by 4 x screws (J), tighten with a screwdriver.
7. Repeat above steps to assembled another drawer.
STEP ELEVEN
×2
1. Put drawers into the assembled unit onto the
drawer runners.
2. Insert 2 x dowels (D) into each of drawer sides.
Insert drawers half way into the unit then push the
STEP TWELVE
×2
Page 7 of 8

1. Slid 8 x name card (K) into the space of handle
STEP THIRTEEN
K×8
2. WARNING: Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
3. NOTE: Wall fixings are not included, please source
suitable fixings for your wall type. If in doubt, please
consult a qualified tradesman.
STEP FOURTEEN
1. Move the item into position and attach the end of
the strap to the wall with the appropriate screw,
washer and wall plug for your wall type.
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Page 8 of 8