Next NEWSTEAD WHT BED 862920 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittingsplease contact Customer
Services Tel: [phone]
•Made in China.
•We suggest you spend a short time reading through this leaet and then follow the simple step-by-step instructions.
•Carefully check that you have all parts before beginning assembly.
•Keep ttingsoutof children's reach and keep children well away from the construction area.
•We recommend that the packaging isused to protect the surfaces during assembly.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assemblyitems cannotbe returned once assemblyispart or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
•Made from metal with a powder coating nishing.
•
A mattress measuring 150cm x 200cmisintended for use with this bed.
CARE INSTRUCTIONS
•A minimum of 2 personsis required to assemble this product.
•WARNING: Do notuse the bed if any part isbroken, torn or missing and use only spare parts approved by the
manufacturer.
PRODUCTINFORMATION
•Avoid keeping furniture in direct sunlightor close to any heat sources as this can cause cracking, discolouration or
warping.
•Never drag pieces of furniture across the oor as this will cause damage to the joints.
•All assembly xings should always be tightened properly and periodically check all xings and tighten if necessary.
•Forgeneral cleaning, periodicallydust with a soft cloth.
•Do not rub or scrub the surface when cleaning.
•Do notuse abrasive cleaning products or those containing silicone.
•Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
862920 NEWSTEAD WHT BED - KING
Page 1 of 4

1. Attach 4 x feets (6) to headboard (1) and
footboard (2) with 4 x bolts (A) and use allen key (F)
to tighten.
2. Attach 4 x form pads (12) to the bottom of each
leg.
3. Attach 4 x finials (11) to the top of headboard (1)
and footboard (2) with 4 x bolts (C), tighten by hand
turning clockwise.
1. Attach 2 x side rails (3) to headboard (1) and
footboard (2) with 8 x bolts (A), 8 x washers (D) and
8 x rubber washers (E) and use allen key (F) to
tighten.
STEP ONE
STEP TWO
FITTINGS
PARTS
Page 2 of 4

1. Attach 2 x support rails (5) to 1 x centre rail (4)
with 4 x bolts (A) and 4 x washers (D) and use
allen key (F) to tighten.
2. Attach 2 x support legs (7) to 1 x centre rail (4)
with 2 x bolts (B) and 2 x washers (D) and use
allen key (F) to tighten.
1. Attach 2 x support rails (5) to 2 x side rails (3)
with 4 x bolts (A), 4 x washers (D) and use allen key
(F) to tighten.
1. Insert 32 x plastic caps (10) to 2 x wooden slats
(8). Ensure the curve of the slats are facing
upwards.
STEP THREE
STEP FOUR
STEP FIVE
Page 3 of 4

1. Insert 2 x wooden slats (8) to 16 x centre slat
caps (9). Firmly press 16 x centre slat caps (9) into
the holes on 1 x centre rail (4), then firmly press 32 x
plastic caps (10) into the holes on 2 x side rails (3).
N.B.: Ensure the curve of the slats facing upward.
2. Ensure the two ends of fabric straps are
wrapped around support rails (5) tightly.
IMPORTANT: Once the support legs (7) have been
assembled and attached they should be adjusted to
ensure they do not touch the floor (5mm above floor)
to allow for movement once the mattress is placed
on the bed frame.
It is important to note that when moving the bed
ensure that it is not dragged into its new position to
prevent the possibility of these feet being twisted or
angled to one side which could lead to the collapse
of the centre of the bed.
Remove the mattress and lift the bed into its new
position to avoid damaging the bed. Ensure the feet
are at 90۫ to the floor before replacing the mattress.
STEP EIGHT
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SIX
STEP SEVEN
Page 4 of 4