Next SALISBURY 793094 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Carefully check that you have all parts before beginning assembly.
• For general cleaning, periodically dust with a soft cloth.
CARE INSTRUCTIONS
• Keep fittings out of children's reach and keep children well away from the construction area.
• Natural features ensure that each piece is individual. Every effort is made to ensure colour continuity between
pieces, however this is a natural product, slight colour variations and natural grain markings may occur.
PRODUCT INFORMATION
• A minimum of 2 persons is required to assemble this product.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Made from Pine with NC lacquer finish.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Made in China.
• All assembly fittings should always be tightened properly. Screws should not be loose because a clild can squeeze
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Do not rub or scrub the surface when cleaning.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
793094 SALISBURY SINK CONSOLE
Page 1 of 7

FITTINGS
PARTS
A×16 B×16 C×16
J×2
Page 2 of 7

1. Attach 1 x magnet (G) to panel(4) by 2 x screws(H),
tighten with a screwdriver.
2. Insert 4 x dowel (C ) to panel (8) &(9)
3. Attach 2 x metal plate (J) to 2 x door panel(5) by 2
x screws(I),tighten with a screwdriver.
and attach 4 x hinge component (L) to 2 x panel(5) by
8 x screws(M), tighten with a screwdriver.
4. Insert 4 x dowels (C ) into panel (7)
5. Insert 4 x dowels (C ) into panel (6)
6. Insert 8 x cambolts(A) into panel (2), tighten with a
screwdriver and insert 2 x dowels(C ) into panel (2).
7. Attach 2 x hinge components (K) to panel (2) by 8
x screws(M), tighten with a screwdriver.
8. Insert 8 x cambolts(A) into panel (3), tighten with a
screwdriver and insert 2 x dowels(C ) into panel (3).
9. Attach 2 x hinge components (K) to panel (3) by 8
x screws(M), tighten with a screwdriver.
STEP ONE
A
AA
AA
A
A
AAA
A
A
A
C
C
C
C
C
C
C
C
C
C
C
C
G
H
H
I
J
M×4
M×8
K×2
M×8
K×2
4
8
9
5×2
7
6
2
Page 3 of 7

1. Attach panel (6) to panel (8) by 3 x screws(D),
tighten with a screwdriver.
1. Attach assembled panel (6), (8) & panel (9) to
panel (2).
2. Insert 5 x camlocks(B) into panel (6),(8) & (9),
tighten with a screwdriver.
Ensure the arrow indicators on the camlocks are
pointing towards the panel edges and ensure the
assembly bolts locate properly into the camlocks
before turning clockwise with a screwdriver to
tighten.
1. Attach panel (7) to panel (2).
2. Insert 2 x camlocks(B) into panel(7), tighten with a
screwdriver.
STEP TWO
STEP THREE
STEP FOUR
D
D
D
2
B
B
B
8
6
9
7
Page 4 of 7

1. Attach panel (4) to panel (2) and Insert 1 x
camlock(B) to panel 4, tighten with a screwdriver.
2. Attach panel (3) onto assembled unit and insert
8 x camlocks(B), tighten with a screwdriver.
Ensure the arrow indicators on the camlocks are
pointing towards the panel edges and ensure the
assembly bolts locate properly into the camlocks
before turning clockwise with a screwdriver to
tighten.
1. Turn assembled unit stand up.
2. Attach top panel(1) onto assembled unit with 4 x
screws (E), tighten with allen key (F).
STEP SIX
STEP FIVE
B
B
B
BB
B
3
4
1
E
E
E
E
F
F
Page 5 of 7

1. Lie down assembled unit.
2. Insert 2x screws (D) to panel (4), tighten with a
screwdriver.
1. Attach 1 x wall attachment strap (R) to the back of
the top panel with 1 x washer (Q) and 1 x screw (S).
STEP SEVEN
STEP EIGHT
D
D
Page 6 of 7

1. Attach 2 x door panel (5) hinge arm (L) to hinge
component (K) on side panels.
2. Attach 2 x handles (O) to door panels (5) by 2 x
screws (P), tighten with a screwdriver.
3. To align doors use the adjustment diagram below
3. NOTE: Wall fixings are not included, please source
suitable fixings for your wall type. If in doubt, please
consult a qualified tradesman.
STEP TEN
1. Move the item into position and attach the end of
the strap to the wall with the appropriate screw,
washer and wall plug for your wall type.
2. WARNING: Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
STEP NINE
O
O
P
P
3
4
1
2
Page 7 of 7