NEXTIVITY CEL-FI LTEM-EU User manual

The Modem & Mag-Mount Antenna must be installed where a strong
LTE signal is available or adjacent to the CEL-FI GO/QUATRA device by
coupling the CEL-FI donor antenna signal for the Modem.
Install the modem on a wall at a suitable location using included
Mounting Hardware
Note: Separate coupler and SMA(m-m) coaxial cable needed for
installation configuration option 2.
The Modem & Mag-Mount Antenna must be installed where a strong
LTE signal is available or adjacent to the CEL-FI GO/QUATRA device by
coupling the CEL-FI donor antenna signal for the Modem.
Install the modem on a wall at a suitable location using included
Mounting Hardware
Note: Separate coupler and SMA(m-m) coaxial cable needed for
installation configuration option 2.
11
11
LED Label Status Indication
PWR ON Powered ON
OFF Powered OFF
Signal Strength Single/Dual/All Weak/Normal/Strong
SYS Blink Normal Operation
OFF The modem is not working
Online ON The modem can access the internet
OFF The modem cannot access the internet
Alarm
ON SIM Card is not inserted properly LTE
Signal is too weak
Blink The modem could not register on the
network.
OFF Normal Operation
WAN ON WAN is connected
OFF WAN is not connected
LAN Blink Normal LAN operation
OFF LAN is not connected
LED Label Status Indication
PWR ON Powered ON
OFF Powered OFF
Signal Strength Single/Dual/All Weak/Normal/Strong
SYS Blink Normal Operation
OFF The modem is not working
Online ON The modem can access the internet
OFF The modem cannot access the internet
Alarm
ON SIM Card is not inserted properly LTE
Signal is too weak
Blink The modem could not register on the
network.
OFF Normal Operation
WAN ON WAN is connected
OFF WAN is not connected
LAN Blink Normal LAN operation
OFF LAN is not connected
Copyright © 2022 by Nextivity, Inc, U.S. Patents pending. All rights reserved. The Nextivity
and CEL-FI logos are registered trademarks of Nextivity Inc. All other trademarks or registered
trademarks listed belong to their respective owners.
Copyright © 2022 by Nextivity, Inc, U.S. Patents pending. All rights reserved. The Nextivity
and CEL-FI logos are registered trademarks of Nextivity Inc. All other trademarks or registered
trademarks listed belong to their respective owners.
qsg-connect-c41_eng_22-1116
qsg-connect-c41_eng_22-1116
Kit#
LTEM-EU
Kit#
LTEM-EU
Included In the Box
Included In the Box
Select Modem Installation Location
Select Modem Installation Location
Modem
Modem
Category Cable
Category Cable
Mag-mount Antenna
Mag-mount Antenna
Mounting Hardware
Mounting Hardware
AC Adapter
AC Adapter
SIM Card Adapter
SIM Card Adapter
CEL-FI®
LTE Modem
Quick Start Guide
CEL-FI®
LTE Modem
Quick Start Guide

Quick Installation
Quick Installation
22
22
33
33
44
44
55
55
66
66
IMPORTANT: Your External Modem is an electronic device. It
must be kept indoors and in a dry, cool, well-ventilated area.
IMPORTANT: Your External Modem is an electronic device. It
must be kept indoors and in a dry, cool, well-ventilated area.
When the Modem is powered off, use sim card ejector to push the but-
ton adjacent to the SIM card tray to eject it. Place the SIM card in the
tray with the chip facing up. Insert the SIM card tray with the SIM into
the Modem. Make sure the SIM card tray is all the way in.
Note: The Modem can only be used with a standard SIM; hence, if you
have a micro/nano SIM, please use the included SIM Card Adapter.
Warning: Do not install or swap the SIM card when the Modem is
powered on.
When the Modem is powered off, use sim card ejector to push the but-
ton adjacent to the SIM card tray to eject it. Place the SIM card in the
tray with the chip facing up. Insert the SIM card tray with the SIM into
the Modem. Make sure the SIM card tray is all the way in.
Note: The Modem can only be used with a standard SIM; hence, if you
have a micro/nano SIM, please use the included SIM Card Adapter.
Warning: Do not install or swap the SIM card when the Modem is
powered on.
Connect the included Mag-mount Antenna with the ANT SMA(f) port on
the Modem.
Alternate: A coupler can be used unequally to split the donor antenna
signal between the Modem and CEL-FI donor input.
Connect the included Mag-mount Antenna with the ANT SMA(f) port on
the Modem.
Alternate: A coupler can be used unequally to split the donor antenna
signal between the Modem and CEL-FI donor input.
Power on the Modem by plugging in the included AC adapter.
Power on the Modem by plugging in the included AC adapter.
Connect the LAN port on the modem with the LAN port on the Nextivity Solution
using Category Cable.
If the Modem Online LED is solid ON, your CEL-FI GO/QUATRA device is now online.
If not, the SIM may require custom APN and PIN settings. Continue to Step 5 to
configure them in Modem settings in Setup -> WAN.
Connect the LAN port on the modem with the LAN port on the Nextivity Solution
using Category Cable.
If the Modem Online LED is solid ON, your CEL-FI GO/QUATRA device is now online.
If not, the SIM may require custom APN and PIN settings. Continue to Step 5 to
configure them in Modem settings in Setup -> WAN.
Using a Category Cable, connect the Modem to your
PC. Open the browser on your PC and input the IP
address below with login credentials to access the
Modem settings.
IP Address: 192.168.1.1
Default Password: admin
Using a Category Cable, connect the Modem to your
PC. Open the browser on your PC and input the IP
address below with login credentials to access the
Modem settings.
IP Address: 192.168.1.1
Default Password: admin
Note: To prevent
unauthorized access to the
modem or disruption, ensure
to change the password
from default.
Note: To prevent
unauthorized access to the
modem or disruption, ensure
to change the password
from default.
Insert your SIM card
Insert your SIM card
IInstall the Cellular Antenna
IInstall the Cellular Antenna
Power Supply
Power Supply
Connect the Nextivity Solution
Connect the Nextivity Solution
Change Modem login Password
Change Modem login Password