NexxTech 2100972 User manual

Magnetic Mount Mobile CB Antenna
The Nexxtech Magnetic Mount Mobile CB Antenna mounts
securely to any flat magnetic metal surface. The magnetic base
stays in place at normal highway speeds. Your antenna can
handle a maximum power output of 25 watts.
The antenna was designed for use on all 40-channel CBs or
with a 30’ (10 m) amateur radio transceiver. You can adjust the
stainless steel whip for the lowest standing wave ratio (SWR) and
maximum RF signal radiation.
PARTS LIST
Description Quantity
(1) Whip assembly 1
(2) Spring Adapter 1
(3) Magnet/Cable Assembly 1
(4) Set Screw 1
(5) Allen Wrench 1
Page 1
2100972
INSTALLATION
Installing the bracket
1. Choose a clean, flat magnetic metal surface for your antenna
location.
Caution: Do not mount your antenna on a vinyl-covered
surface.
2. Route the coaxial cable from the magnet/cable assembly (3)
to your CB. Be sure that the cable does not get pinched in
doors or windows.
Note: In some installations, the distance from your antenna
to your CB might be greater than the length of the supplied
coaxial cable. Your local electronics store has a selection of
cable and connectors.
3. Connect the antenna cable plug to your CB/Ham Transceiver.
4. Securely screw the whip adapter (2) to the magnet/cable
assembly (3).
5. Insert the whip assembly (1) into the whip adapter (2) and
tighten the set screw (4) with the supplied Allen wrench (5).
Note: Occasionally remove the magnetic base and clean
the contact surfaces with fresh water and detergent.
Condensation trapped between the magnetic base and
mounting surface might discolor the vehicle’s finish if the base
is left in one position for too long.
TUNING THE ANTENNA FOR CB
The antenna was designed for full 40-channel operation. To
ensure that the antenna works with a minimum SWR on all
channels on all types of vehicles, we have allowed extra whip
length for proper tuning.
You need an SWR meter, available at your local electronics store,
to properly tune your CB/Ham System.
1. Connect the SWR meter between the CB and the coaxial
antenna cable, as described in the meter’s instructions.
2. Measure the SWR on your CB’s lowest and highest channels.
If the SWR reading on the lowest channel is higher than the
value in the chart, lengthen the antenna by loosening the set
screw (using the supplied Allen wrench) and pulling the whip
out of the base 1/8 inch (3 mm), then tightening the screw
again.
If the SWR reading on the highest channel is higher than the
value in the chart, shorten the antenna by loosening the set
screw (using the supplied Allen wrench), removing the whip
SWR
∞
4.0
3.5
3.0
2.5
2.0
1.6
1.5
1.3
1.1
1.0
CHAN. 1 CHAN. 19 CHAN. 40

Page 2
from the coil, and cutting 1/8 inch (3 mm) from the whip’s
lower end. Replace the whip and tighten the screw.
Note: You can use large wire cutters or a hacksaw to cut the
whip. Or, you can use a file to make a small groove around
the whip, then break off the length you need to remove.
3. Measure the SWR again. Repeat the adjustment and the
SWR measurement, as necessary, until the SWR readings
are nearly equal. Cut only 1/8 inch (3 mm) at a time and
measure the SWR after each adjustment.
TUNING FOR THE 30’ (10 m) HAM BAND
You can tune your antenna to operate on part of the 30’ (10 m)
band, using a 30’ (10 m) band Amateur Radio transceiver. Your
antenna’s bandwidth is 1000 kHz (1.0 MHz), and it can handle up
to 25 watts. Use the chart to determine the length to which you
need to cut the whip for a specific center frequency.
1. Determine the center frequency of the portion of the 30’ (10
m) band you want to operate on. For example, if you want to
operate from 28.1 MHz to 29.1 MHz, the center frequency is
28.6 MHz.
2. Cut the whip to the length indicated for that frequency. For
example, the length is about 47 7/8 inches (121.6 cm) for
28.6 MHz.
3. Connect an SWR meter between your antenna and the
transceiver.
4. Measure your system’s SWR on the center frequency.
5. Use the supplied Allen wrench to loosen the set screw and
pull the whip out about 1/8 inch (3 mm).
6. Measure your system’s SWR again.
If the SWR increased, return your antenna to its previous
position. If the whip is fully inserted, remove it from the base
and cut off 1/8 inch (3 mm).
If the SWR decreased, pull the whip out about another 1/8
inch (3 mm).
7. Measure the SWR again. Repeat the adjustment and the
SWR measurement, as necessary, until the SWR readings
are nearly equal. Cut only 1/8 inch (3 mm) at a time and
measure the SWR after each adjustment.
Who is Providing This Warranty?
• Orbyx Electronics, LLC (”Orbyx”), as the distributor of this NexxtechTM product (your
“Product”).
What Does This Warranty Cover?
• This warranty covers defects in materials or workmanship in your Product under normal
use and conditions.
What is the Period of Coverage?
• This warranty covers your Product for 90 days from the original purchase date.
Who Is Covered?
• This warranty covers the original consumer purchaser. Coverage terminates if you sell
or otherwise transfer your Product.
What Will We Do To Correct Problems?
• We will repair your Product or replace your Product with a new or reconditioned
equivalent product, at our option.
How Do You Get Service?
• Call Orbyx TOLL FREE at 1-866-363-3059 for instructions for obtaining warranty
service from Orbyx’s authorized service providers.
• Or, return your Product directly to the retail store from which you purchased the
Product.
• When you obtain service for your Product, you must provide a purchase receipt (or
other proof of the original purchase date) and a description of the defect(s).
What Does This Warranty Not Cover?
• This warranty DOES NOT COVER:
• damage due to misuse, abuse, alteration, unauthorized repair, or accident (such as
improper electrical current);
• damage due to “acts of God” (such as lightning) or other contingencies beyond our
control;
• cosmetic damage;
• externally generated static, signal reception or antenna problems not caused by your
Product; or batteries.
• This warranty also DOES NOT COVER, and in no case will we be liable for, any
incidental damages (such as transportation costs to and from an authorized service
provider, or loss of time) or consequential damages (such as costs of repairing or
replacing other property which is damaged, including tapes, discs, speakers not
included with your Product or other accessories, or external electrical systems)
resulting from the use of your Product. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
• Defacing the serial number, or using your Product for commercial or institutional
purposes, voids this warranty.
Are There Other Warranties?
• There are no express warranties other than those expressed herein. Neither the sales
personnel nor any other person is authorized to make any other warranties or to extend
the duration of any warranties.
• ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY (AN UNWRITTEN WARRANTY THAT A PRODUCT IS FIT FOR
ORDINARY USE), ARE LIMITED TO 90 DAYS. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
How Does State Law Apply?
• This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
LIMITED WARRANTY
LIMITED WARRANTY
Limited Warranty/Garantie Limitée
U.S.A & Canada
© 2005 ORBYX Electronics. All Rights Reserved.
-0.6 MHz +0.6 MHz SWR
∞
4.0
3.0
2.5
2.0
1.5
1.1
1.0
38
37
36
35
34
33
32
31
30
28.0 28.2 28.4 28.6 28.8 29.0 29.2 29.4 29.6
Length (Inches)
Frequency (MHz)
ORBYX ELECTRONICS WARRANTY
ORBYX Electronics warrants that this product will be free from defects in materials and
workmanship for a period of ninety (90) days from the date of purchase. Within this period,
simply take the product and your proof of purchase to any ORBYX Electronics store
or dealer and the product will be repaired without charge for parts and labour. ORBYX
Electronics reserves the right to charge for transportation. Any product which has been
subject to misuse or accidental damage is excluded from this warranty.
This warranty is only applicable to a product purchased through ORBYX Electronics’
company owned stores and dealers and to a product that is presented for repair in a
country where ORBYX Electronics offers the product for sale. While this warranty does not
confer any legal rights other than those set out above, you may have additional statutory
rights which will vary under the laws of the various countries, states, province and other
governmental entities in which ORBYX Electronics operates. This warranty is subject to all
statutory rights you may have in the country of purchase.
Distributed exclusively in the U.S. by Orbyx Electronics, LLC
501 South Cheryl Lane, Walnut, CA 91789
Imported in Canada for/Importé au Canada pour
Orbyx Electronics, Concord, Canada, L4K 4M3
Manufactured in China
For product support please contact www.orbyxelectronics.com or 1-866-363-3059.