mm
FUNCTION SETUP
mm
1
mm
mm
TOL
1
mm
1
mm
TOLINPUT
1
mm
TOLINPUT
1
TOL
mm
1
PRESET INPUT
mm
1
mm
1
mm
※This option
not used
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
【Measurement Display】
Press the [MODE]Button, or Press-and-hold, to access and cycle through the functions
as show in the chart below. When the function is displayed, press Center Button to access.
※If no operation is performed after 5 seconds, display will return to measurement screen.
[MODE]Button
[MODE]Button
[MODE]Button
[MODE]Button
Long Press
[MODE]Button
Return to
Measurement Display
【REF1 / REF2 Mode】
Two different Zero points, REF1 and REF2 can
be used (also Tolerance settings.)This feature is
helpful when there are multiple measurement
criteria in use at the same time.
【Preset Value】
Any number can be preset for use in setting display
during measurement by using this function.
●Press [SET]in measurement screen to set display
the preset value.
Press Center Button for numeric display. Press
Center Button to move the cursor, and [SET]to
change the value of that character. Press [Mode]to
enter.
To Set
Press Center Button to display REF1 / REF2, then
press [SET]to select.
To Set
●Center Button can be programmed to call up a frequently used
function with a single press while taking measurements.
※Programmed setting is reset when power is turned off.
Programmable “Favorite”Button
Press and hold the Center “Favorite”Button to enter the button
programming selection mode.Press Center Button to cycle through the
options and then press [MODE]or [SET]to select.
To Set
Long Press
Center Button
※This option
not used
※This option
not used
Hold function
Reset MIN,
MAX, DELTA
display
Zero setting
Switch
REF1 / REF2
Center Button Center Button
Center Button
Center Button
Center Button
Center Button
Center Button
Center Button
Center Button
Center Button
Center Button
Center Button
Preset
NOR, MIN,
MAX, DELTA
mode
Tolerance
Setting function
ON / OFF
Resolution setting
0.001 / 0.0001
Measurement
Direction ＋/ −
Calculation
function
※Set to 1.000
to disable
●
●
●
●
●
●
●
●
●
This is a precision instrument, handle with care. Do not drop or subject
to excessive forces.
Keep away form high voltage and strong magnetic fields; instrument
damage may result.
Do not use or store in direct sunlight or locations with high
temperatures such as in a car, or near a stove or heat source.
When taking measurements, hold gauge securely, such as in
magnetic base. (sold separately)
Please do not disassemble or modify.
Remove dust and cutting chips after use and apply rust preventative
oil to metallic surfaces. Please keep out of reach of children.
Do not use organic solvents to clean the body of the instrument.
When not being used for a long period of time, please remove battery.
Only use as directed. Improper use may cause accident or injury.
CAUTION
I303-K
1606
Niigata seiki Co., Ltd.
6-15-22, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-31-5670 Fax. : +81-256-39-7730
URL http://www.niigataseiki.co.jp
【Display Mode】
Press Center Button
to move the cursor,
and [SET]to change
the value of that
character. Press
[Mode]to enter.
【Tolerance Function】
With tolerance values set, gauge will show if
measurement is within range.
Colored lights will show tolerance determination
for
easy
judgment.
To reverse the display indication, reverse the entry of the Lower and
Upper limits.
【Measurement Direction】
mm
mm
【Calculation Function】
You can enter a number to multiply by the
amount of Spindle movement.
mm
【Auto Off】
mm
【Button Lock】
For locking buttons while taking measurements.
mm
●When lock is ON,『 』icon will display on LCD.
●To release the lock mode, press and hold [SET]
until “”is displayed.
Ex: If computation factor is set to “2.00", and measured value is “4.25”
(actual amount of Spindle motion,)the displayed reading will be “8.50”
Set Lower
Limit
Set Upper
Limit
For measurement Lower limit set to “+3”, Upper limit set to “+6”
Measurement: 2.25mm
Red Light
Measurement: 4.00mm Measurement: 7.25mm
Measurement: 7.25mm
Orange Light
Ex:
Green Light
OK
For measurement Lower limit set to “+6”, Upper limit set to “+3”
Red Light
Measurement: 4.00mmMeasurement: 2.25mm
Orange Light
Ex:
Green Light
OK
Set measurement mode: (MIN),(MAX),
(MINMAX),or
(NORMAL)
※“deltA”(MINMAX)
→Display maximum displacement without regard to direction (TIR).
[MODE]Button
[MODE]Button
[MODE]Button
[MODE]Button
[MODE]Button
[MODE]Button
[MODE]Button
[MODE]Button
[MODE]Button
Center Button Center Button
Press Center Button to display options, then press
[SET]to select.
To Set
【Resolution】
Press Center Button to display 0.001 / 0.0001,
then press [SET]to select.
To Set
Press Center Button to display ON / OFF, then
press [SET]to select.
To Set
Press Center Button to move the cursor, and [SET]
to change the value of that character. Press [Mode]
to enter.
To Set
Press Center Button to display “ ” / “”,
and press [SET]to select.
『』…disabled『』… Auto off if idle for 20 min.
To Set
Press Center Button to display (＋)/ (−), then
press [SET]to select.
To Set
※Tolerance values can be set for MIN,
MAX, and DELTA modes.
