Nikon LITE TOUCH ZOOM 110S User manual

En
De
Es
Instruction Manual (Pages 2-43)
Bedienungsanleitung (Seite 44-85)
Manuel d’utilisation (Pages 86-127)
Manual de instrucciones (Páginas 128-169)
Instruction Manuals
Fr

2Getting Started
To prevent damage to your Nikon product or injury to yourself or to
others, read the following safety precautions in their entirety before
using this equipment. Keep these safety instructions where all those
who use the product will read them.
The consequences that could result from failure to observe the
precautions listed in this section are indicated by the following symbols:
WARNINGS
Do not look at the sun through the viewfinder
Viewing the sun or other strong light source through the
viewfinder could cause permanent visual impairment.
Turn off immediately in the event of malfunction
Should you notice smoke or an unusual smell coming from
the equipment, remove the battery immediately, taking care to
avoid burns. Continued operation could result in injury. After
removing the battery, take the equipment to a Nikon-
authorized service center for inspection.
Do not use in the presence of flammable gas
Do not use electronic equipment in the presence of flammable
gas, as this could result in explosion or fire.
Observe caution when using the camera strap
Caution should be exercised to prevent strangulation when
wearing the camera strap around your neck. Never place the
strap around the neck of an infant or child.
Do not disassemble
Touching the product’s internal parts could result in injury. In the
event of a malfunction, the product should be repaired only by a
qualified technician. Should the product break open as the result
of a fall or other accident, remove the battery and then take the
product to a Nikon-authorized service center for inspection.
For your safety
(Caring for the Camera and Battery)
This icon marks warnings, information that should be
read before using your Nikon product to prevent
possible injury.

En
3Getting Started
Observe proper precautions when handling batteries
Batteries may leak or explode if improperly handled. Observe
the following precautions when handling batteries for use in
this product:
•Be sure the product is off before replacing the battery.
•Use only a 3 V CR123A or DL123A lithium battery.
•When inserting the battery, do not attempt to insert it upside
down or backwards.
•Do not short or disassemble the battery.
•Do not expose the battery to flame or to excessive heat.
•Do not immerse in or expose to water.
•Do not transport or store with metal objects such as necklaces
or hairpins.
•Immediately after use, or when the product is used on battery
power for an extended period, the battery may become hot.
Before removing the battery, turn the camera off and allow
the battery to cool.
•Discontinue use immediately should you notice any changes
in the battery, such as discoloration or deformation.
Keep out of the reach of children
Particular care should be taken to prevent infants from putting
the battery or other small parts into their mouths.
Observe caution when operating the flash
Using the flash close to your subject’s eyes could cause
temporary visual impairment. Particular care should be
observed if photographing infants, when the flash should be no
less than one meter from the subject.

4Getting Started
Keep dry
This product is not waterproof, and may malfunction if immersed in
water or exposed to high levels of humidity. Rusting of the internal
mechanism can cause irreparable damage.
Keep free of salt, sand, and dust
After using your camera at the beach or seaside, wipe off any
sand or salt with a lightly dampened cloth and then dry your
camera thoroughly.
Do not touch the lens with your fingers
Use a blower brush to remove dirt and dust from the lens. To
remove fingerprints or smudges from the lens’ surface, use a
soft, clean cotton cloth or lens tissue moistened with ethanol
(alcohol) or lens cleaner.
Handle the slide cover and all moving parts with care
Do not apply force to the lens or flash unit, or to the battery
chamber cover or slide cover. These parts are especially
susceptible to damage.
Do not drop
The product may malfunction if subjected to strong shocks or
vibration.
Keep away from strong magnetic fields
Do not use or store this device in the vicinity of equipment
that generates strong electromagnetic radiation or magnetic
fields. Strong static charges or the magnetic fields produced
by equipment such as radio transmitters could affect the
product’s internal circuitry.
Avoid sudden changes in temperature
Sudden changes in temperature, such as occur when entering
or leaving a heated building on a cold day, can cause
condensation inside the device. To prevent condensation, place
the device in a carrying case or a plastic bag before exposing it
to sudden changes in temperature.
Caring for the Camera and Battery

En
5Getting Started
Batteries
•When you turn the device on, check the battery-level
displayed on the LCD panel to determine whether the battery
needs to be replaced. The battery needs to be replaced the
low battery power indicator appears on the LCD panel.
•Ready a spare battery when taking pictures on important
occasions. Depending on your location, you may find it
difficult to purchase replacement batteries on short notice.
• On cold days, the capacity of batteries tends to decrease. Use
a fresh battery at low temperatures. Keep a spare battery in a
warm place and exchange the two as necessary. Once
warmed, a cold battery may recover some of its charge.
•Should the battery terminals become dirty, wipe them off with
a clean, dry cloth before use.
Storage
•To prevent mold or mildew, store the camera in a dry, well-
ventilated area. If you will not be using the product for a long
period of time, remove the battery to prevent leakage and store
the camera in a plastic bag containing a desiccant. Do not,
however, store the camera case in a plastic bag, as this may
cause the material to deteriorate. Note that desiccant gradually
loses its capacity to absorb moisture and should be replaced at
regular intervals.
•Do not store the camera with naphtha or camphor moth balls,
close to equipment that produces strong magnetic fields, or in
areas subject to extremes of temperature, for example near a
space heater or in a closed vehicle on a hot day.
•To prevent mold or mildew, take the camera out of storage at
least once a month. Turn the camera on and release the
shutter a few times before putting the camera away again.
•Store the battery in a cool, dry place.

6Getting Started
Thank you for purchasing the Nikon Lite Touch Zoom 110s / Lite
Touch Zoom 110s QUARTZ DATE (QD) camera.
Be sure to read this manual thoroughly before use, and keep it
handy until you feel confident using the camera.
Strap
Accessory
(The following item is supplied with this camera.)
Optional accessories
•Camera case CS-L28
(Remote control unit can be stored in the pocket inside.)
• Remote control unit ML-L3 ( p. 35)
(Lite Touch Zoom 110s QD only)
Symbols used in this manual
: Indicates items to be checked, such as requirements
and restrictions.
: Indicates notes and cautions you are requested to follow.
: Indicates supplementary descriptions.
: Indicates pages for reference.

En
7Getting Started
For your safety ----------------------------------------- 2
Caring for the Camera and Battery ------------------ 4
To take a picture right away (Quick operation guide) --- 8
Camera parts ------------------------------------------ 10
Body ----------------------------------------------- 10
LCD panel ----------------------------------------- 12
Viewfinder ---------------------------------------- 13
Installing a battery ------------------------------------ 14
Turning the camera on ------------------------------- 15
Checking the battery power ------------------------- 15
Loading the film -------------------------------------- 16
Imprinting the date/time on pictures
(Lite Touch Zoom 110s QD only) ------------------- 18
Holding the camera properly ------------------------ 19
Operating the shutter release button --------------- 19
Shooting ----------------------------------------------- 20
Zooming ----------------------------------------------- 21
Close-up photography ------------------------------- 22
Rewinding the film ----------------------------------- 23
Removing the film ------------------------------------ 23
When the main subject is not in the center of
the picture --------------------------------------------- 24
Difficult-to-focus subjects --------------------------- 25
Flash photography ------------------------------------ 26
Selecting flash mode ---------------------------- 26
To use the flash automatically ------------------ 28
To cancel flash operation ------------------------ 29
To use the flash always -------------------------- 30
To photograph a person in a night view ------- 31
button ----------------------------------------- 32
To reduce the "Red-eye" effect ------------------ 33
Using the self-timer ---------------------------------- 34
Using the remote control (optional)
(Lite Touch Zoom 110s QD only) ------------------- 35
Replacing the remote control battery -------------- 36
Shooting a distant view or landscape through
a window ---------------------------------------------- 37
Correcting the date and time
(Lite Touch Zoom 110s QD only) ------------------- 38
Troubleshooting -------------------------------------- 39
Specifications ----------------------------------------- 41
Table of Contents
Preparations
Basic
Operations
Advanced
Operations
Additional
Information

8Getting Started
2Open the slide cover to
turn the camera on.
(p. 15)
Make sure that the sufficient Battery
Power indicator ( ) appears on
the LCD panel. ( p. 15)
3Load the film.
(p. 16)
Pull the film leader across to the red
index mark inside the film compartment.
1Insert a battery.
(p. 14)
4Press the Zoom lever and
compose your picture.
(p. 21)
To take a picture right away
(Quick operation guide)
For
wide-angle For telephoto
MADEINCHINA

En
9Getting Started
The film starts to rewind
automatically, when film reaches
the end of the roll. (p. 23)
Remove the film cartridge.
(p. 23)
5Press the shutter release
button halfway. (p. 20)
When you press the button halfway,
focus and exposure are automatically
achieved, and the green LED lights up.
6Check the green LED is
on, then press the shutter
release button all the way
to release the shutter.
(p. 20)
Take trial shots
Take trial shots before shooting at important occasions like weddings
or graduations.
•Nikon will not be held liable for any damages resulting from the use
of this product.

10 Getting Started
Camera parts
*Lite Touch Zoom 110s QD only
Body
Viewfinder window
Autofocus window
Slide cover (power switch)
(p. 15)
Strap eyelet
( p. 11)
Shutter release button
(p. 19)
button
Red-eye Reduction
(pp. 32, 33)
Self-timer ( p. 34)
Remote control*( p. 35)
LCD panel
(p. 12)
Lens
Zoom lever ( p. 21)
button
Flash mode ( pp. 26-31)
Infinity Focus mode ( p. 37)
Remote-control
sensor*( p. 35)
Flash
(pp. 26, 27)
Red-eye Reduction lamp
(pp. 32, 33)
Self-timer lamp ( p. 34)
Auto Exposure
metering window
Autofocus
window
Mid-roll rewind button
(p. 23)

En
11Getting Started
MADE IN CHINA
BATT.
Attaching the strap
Put your head
through this
loop.
Attach the strap as shown
in the illustration.
Adjust the length using the
lug on the strap.
Battery
chamber lid
(p.
14)
ADJUST button*
(for correcting date)
(p. 38)
Green LED
(pp. 13, 20)
Orange LED
(pp. 13, 27)
Viewfinder
eyepiece
(p. 13)
SEL button*(for selecting the
position of date to corrected)
(p. 38)
Film confirmation
window
Tripod socket
(pp. 29, 31, 34, 35)
Camera back lock
release lever
(p. 16)
MODE button*
(for selecting date to be
imprinted or corrected)
(pp. 18, 38)
Date panel*
(pp. 18, 38)

12 Getting Started
The illustrations are fully labeled for your reference.
Camera parts (continued)
LCD panel
Red-eye Reduction indicator
(pp. 32, 33)
Infinity Focus
Mode indicator
(p. 37)
Flash Mode indicator
(pp. 26-31)
Frame counter ( p. 17)
Battery power indicator
(p. 15)
Self-timer indicator
(p. 34)
Remote Control
indicator ( p. 35)
(Lite Touch Zoom 110s QD only)

En
13Getting Started
1Parallax compensation marks (p. 22)
Use for close-up shooting distance less than 1m in telephoto
setting.
2Autofocus frame marks (p. 20)
Center the main subject to be in focus with in this frame.
3Orange LED (p. 27)
Slowly blinks while the flash is being charged, and lights up
when the flash is ready to fire.
If you press down on the popped-up flash unit, the LED blinks rapidly
as a warning.
4Green LED (p. 20)
Lights when focus is achieved.
In close-up photography, if the subject is closer than approx. 0.8m,
the green LED blinks as a warning when you press the Shutter
Release button halfway, and the shutter cannot be released. Note
that you may take a picture even if the camera-to-subject distance
is extremely short (approx. 0.1m) and out of the control range of
the camera. However, the focus may not be sharp.
Viewfinder
1
3
4
2

14 Preparations
2Install a new battery.
Insert the battery with the and
ends positioned as marked inside the
battery chamber.
3Close the battery chamber
lid until it clicks.
1Open the battery chamber
lid.
While releasing the lock as indicated by
the arrow in the left illustration, open
the battery chamber lid.
Installing a battery
Battery type
Use one CR123A or DL123A type 3V lithium battery in this camera.
When the battery for the camera is replaced, the date/time may be
reset. Be sure to check the day/time after replacing the battery and
correct if necessary. ( p. 38)
MADEINCHINA
MADEINCHINA
MADEINCHINA
MADEINCHINA

En
15Preparations
Turning the camera on
Open the slide cover until it
clicks.
Once you open the slide cover in the
direction of the arrow, the camera is
turned on, the built-in flash automatically
pops up, and the lens extends out.
The camera is set in Auto flash mode.
(p. 30)
When closing the cover, first slide it slightly in to start lens retraction.
When the lens is completely retracted, slowly close the cover.
Checking the battery power
Make sure that the sufficient Battery Power
indicator ( ) is showing on the LCD panel.
Always check the battery condition before shooting.
We recommend that you take spare batteries with you, especially when
travelling.
The battery power is sufficient.
The battery is nearing exhaustion.
Have a fresh one ready.
Replace the battery with a new one.
showing
blinking
no indicators

16 Preparations
Loading the film
Recommended film
Use DX-coded 35mm film with this camera. It is recommended to use
DX-coded ISO 400 film, which provides good results when using the
flash, and helps avoid blurred images, should camera shake occur.
2Insert a film cartridge.
3Pull the film leader across
to the red index mark inside
the film compartment.
Make sure to align the film leader to the
red index mark; if the film leader is not
properly aligned to the index mark
(short of or beyond the mark), film
may not be loaded properly.
1Close the slide cover, then open
the camera back.
Slide the camera back lock release lever
(1), and open the camera back (2).
When loading/unloading film, be sure
not to open the camera back cover into
direct sunlight.
Hold the film cartridge and ensure film is properly positioned with no slack.
MADEINCHINA
BATT.

En
17Preparations
4Close the camera back, and
check that “ ” appears on
the film counter.
Once the camera back is closed, the
film automatically advances to the first
frame. Until film loading is complete,
“” blinks on the LCD panel.
When the film has been properly set,
“” appears on the LCD panel.
When close the slide cover, frame
counter not appears on the LCD panel.
If “ ” blinks on the LCD panel, film is not properly loaded. Open the
camera back again and reload film.
Tips on DX-coded 35mm film
DX code
Film cartridge
DX mark
Number of frames
ISO (film speed)
With DX-coded film, film speed is set automatically.
Film speeds valid for automatic setting are ISO 50, 100, 200, 400, 800,
1600, and 3200.
With a non-DX-coded film, the film speed is automatically set to ISO 100.

18 Preparations
Select the date/time indicator
by pressing the MODE button.
The year is indicated by the last two
digits, and the time is displayed by 24-
hour clock. The example in the
illustration shows June 1, 2002.
The month is indicated by “ ” in the
display screen. This letter is not
imprinted on any pictures you take.
Each time you press the MODE/SEL button, the indicator
changes as follows:
Day/Month/Year Month/Day/Year
Year/Month/Day Day/Hour/Minute No imprint
Select “ ” (No imprint) to cancel data imprint.
Imprint position of date/time
The imprint positions on picture are shown in the illustration.
It may be difficult to read against bright colors such as white or
reddish hues.
Imprinting the date/time on pictures
(Lite Touch Zoom 110s QD only)
Imprint position

En
19Basic Operations
Holding the camera properly
When holding the
camera horizontally
When holding the
camera vertically
Prop your elbows against your body and hold the camera with both hands.
When holding the camera vertically, make sure that the flash is on top as
shown.
Operating the shutter release button
1Press the shutter release button halfway to
focus.
Before pressing Press all the
way down
Press halfway
When you press the button halfway, focus and exposure are automatically
achieved, and the green LED lights up.
The focus is locked (Focus lock p. 24) while the shutter release
button is depressed halfway.
Do not block the lens, autofocus window, or flash with your fingers or
hair, or the strap.
Be careful not to press down on the flash unit when it is in the popped-
up position.
2Press the shutter release button all the way
down to take a picture.
The flash automatically fires when lighting is poor.
Pressing the shutter release button abruptly can result in picture blur.
Make sure to press the shutter release slowly.

20 Basic Operations
1Center the autofocus
frame marks “ ” on the
main subject.
If the main subject is outside the autofocus frame marks:
Use focus lock. ( p. 24)
2Press the shutter release
button halfway to focus.
Lighting/blinking of the green LED
When correct focus has been achieved, the green LED lights up.
aBlinking indicates the subject is too close.
For correct focus to be achieved, keep the
camera away from the subject for more than
approx. 0.8m (2.6 ft.).
Note that you may take a picture even if the
camera-to-subject distance is extremely
short (approx. 0.1m (0.3 ft.)) and out of the
control range of the camera. However, the
focus may not be sharp.
Shooting