Nilfisk-Advance SC500 User manual

Nilfisk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
[e-mail]
www.nilfisk.com
ATTENTION! Do not use the machine before you have read and understood the Instructions for use manual
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
Make sure the solution valve under
the machine is open.
3. Fill the EcoFlex™ tank with a deter-
gent suitable for cleaning machines
(highly concentrated and low
foaming detergent).
4. Install the squeegee and fasten it
with the knob.
1a. Unplug the Battery charger cable.
Reconnect it to the machine.
1b. Disconnect the battery charger
cable from the electrical socket.
18. Clean the machine using a damp
cloth and where needed use a neu-
tral cleaning product.
16. Press the click-off button and wait
for the brush/pad holder to fall
on the floor. Remove to clean or
change brush.
17. Take the squeegee off and remove
debris. Check and clean the squeegee
blades.
19. Charge the batteries: Connect the
battery charger cable to the electri-
cal socket.
20. Park the machine with the recovery
tank cover open.
13. Empty the recovery tank with the
hose. Then empty the solution tank
with the transparent hose.
12. Machine with Ecoflex, always end the daily
work with turning off the detergent 2 minutes
before finishing by pressing the detergent but-
ton. To rinse out detergent from the system and
brush before handling and cleaning.
10. If necessary press the extra pressure
function (hold for one second).
If necessary press the silent mode
button for extra low sound level.
11. Press the EcoFlex™ button when-
ever you temporarily need a greater
cleaning power.
14. Empty the debris tray and clean/
wash the recovery tank inside.
15. Clean the filter:
A) Close the solution valve under the machine.
B) Remove the transparent cover and the gasket,
then remove and clean the filter inside.
C) Reassemble the filter.
7. Lower the squeegee with the pedal.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
6. Insert the operator key, then start
the machine by pressing the One-
Touch button. To engage the brush,
slightly press the drive paddle and
then release it.
8. Push forward the drive paddle to start
cleaning. Adjust maximum speed by
the speed regulation buttons.
9. To change the solution flow level
push the solution button and
change flow level according to the
cleaning performance and applica-
tion.
If the machine has been used until the Red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
PLEASE ENSURE THE CHARGER IS ALWAYS CONNECTED TO THE BATTERIES EVEN IF NOT USED FOR LONGER PERIOD OF TIME TO PREVENT DAMAGE TO THE BATTERY DUE TO LOW VOLTAGE
At the end of the work
OPERATING GUIDELINES
SC500

Nilfisk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
[e-mail]
www.nilfisk.com
ATTENTION! Do not use the machine before you have read and understood the Instructions for use manual
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brushes
don’t work as they
should?
TROUBLESHOOTING
SC500
1Check if the power cable is correctly
connected.
1Check if the suction hose is
correctly installed and cleaned.
1Check if you have the right
detergent and water settings.
3Check if the brush are correctly in-
stalled and not worn out or if there
are external materials avoiding brush
rotating.
2Check if the battery is charged.
2Open the recovery tank and check
the debris tray and float are clean
and working.
2Check if the solution valve is open.
2Check if there isn’t any brush motor
overload “WARNING ALARM F2”
on the display.
3Restart the machine without press-
ing the paddle.
3Check if squeegee blades are dam-
aged or dirty.
3Check if the solution filter is
cleaned.
1To adjust machine direction turn
front knob until machine is working
straight.
4Check floor inclination is not exeed-
ing specifications.
4Check the lid gasket is in good
and working condition and sealing
when lid is closed.
4Check the EcoFlex™ system is
cleaned, eventually purge the sys-
tem.