Nilfisk-Advance SW5500 User manual

SW5500, FLOORTEC R 985
Instructions for use
Model:
9084410010 - 9084413010
03/2016
(1)
1466465000 English
Instructions for use

Производителя / Výrobce / Hersteller / Fabrikanten /
Fabricante / Tootja / Fabricant / Valmistaja / Manufacturer
/ Kατασκευαστή / Gyártó / Proizvođač / Costruttore
/ Gamintojas / Ražotājs / Produsenten / Fabrikant /
Fabricante / Producenta / Producător / Производителем /
Tillverkaren / Výrobca / Izdelovalec / Üretici :
Nilsk S.p.A.
Strada Comunale della Braglia, 18 - 26862 - GUARDAMIGLIO (LO) - ITALY
Tel: [phone], Fax: [phone]
Authorized signatory: Sergio Coccapani, R&D Director
Date: Signature:
Сертификат за съответствие
Osvědčení o shodě
Konformitätserklärung
Overensstemmelsescertikat
Declaración de conformidad
Vastavussertikaat
Déclaration de conformité
Yhdenmukaisuustodistus
Conformity certicate
Πιστοποιητικό συμμόρφωσης
Megfelelősségi nyilatkozat
Potvrda sukladnosti
Dichiarazione di conformità
Atitikties deklaracija
Atbilstības deklarācija
Konformitetssertisering
Conformiteitsverklaring
Declaração de conformidade
Deklaracja zgodności
Certicat de conformitate
Заявление о соответствии
Överensstämmelsecertikat
Certikát súladu
Certikat o ustreznosti
Uyumluluk sertikası
EC Machinery Directive 2006/42/EC EN ISO 12100, EN ISO 13857, EN 349, EN 982
EN 60335-1, EN 60335-2-72, EN 50366
Directive 2014/30/EU EN 55014-1, EN 55014-2, EN 61000-6-2
Долуподписаният потвърждава, че
гореспоменатият модел е произведен в
съответствие със следните директиви
и стандарти. Техническият файл е
съставен от производителя.
Níže podepsaný stvrzuje, že výše
uvedený model byl vyroben v souladu
s následujícími směrnicemi a normami.
Autorem technického listu je výrobce.
Der Unterzeichner bestätigt hiermit dass
die oben erwähnten Modelle gemäß
den folgenden Richtlinien und Normen
hergestellt wurden. Die technische
Dokumentation wird vom Hersteller erstellt.
Undertegnede attesterer herved, at
ovennævnte model er produceret i
overensstemmelse med følgende
direktiver og standarder. Den tekniske l er
udarbejdet af fabrikanten.
El abajo rmante certica que los modelos
arriba mencionados han sido producidos
de acuerdo con las siguientes directivas
y estandares. El fascículo técnico está
redactado por el fabricante
Allakirjutanu kinnitab, et ülalnimetatud
mudel on valmistatud kooskõlas järgmiste
direktiivide ja normidega. Tehnilise
dokumentatsiooni koostab tootja.
Je soussigné certie que les modèles ci-
dessus sont fabriqués conformément aux
directives et normes suivantes. Le dossier
technique est rédigé par le fabricant.
Allekirjoittaia vakuuttaa että yllämainittu
malli on tuotettu seuraavien direktiivien ja
standardien mukaan. Valmistaja kääntää
teknisen tiedoston.
The undersigned certify that the above
mentioned model is produced in
accordance with the following directives
and standards. The technical le is
compiled by the manufacturer.
Ο κάτωθι υπογεγραμμένος πιστοποιεί ότι η
παραγωγή του προαναφερθέντος μοντέλου
γίνεται σύμφωνα με τις ακόλουθες
οδηγίες και πρότυπα. Το τεχνικό αρχείο
συντάσσεται από τον κατασκευαστή.
Alulírottak igazoljuk, hogy a fent említett
modellt a következő irányelvek és
szabványok alapján hoztuk létre. A műszaki
fájlt a gyártó készítette.
Potpisani potvrđujem da gore spomenuti
model proizveden u skladu sa sljedećim
direktivama i standardima.Tehničku
dokumentaciju sastavlja proizvođač.
Il sottoscritto dichiara che i modelli sopra
menzionati sono prodotti in accordo con le
seguenti direttive e standard. Il fascicolo
tecnico è redatto dal costruttore.
Toliau pateiktu dokumentu patvirtinama,
kad minėtas modelis yra pagamintas
laikantis nurodytų direktyvų bei standartų.
Techninę bylą sudarė gamintojas.
Ar šo tiek apliecināts, ka augstākminētais
modelis ir izgatavots atbilstoši šādām
direktīvām un standartiem. Tehnisko
aprakstu ir sastādījis ražotājs.
Undertegnede attesterer att ovennevnte
modell är produsert i overensstemmelse
med fölgende direktiv og standarder. Den
tekniske len er opprettet av produsenten.
Ondergetekende verzekert dat de
bovengenoemde modellen geproduceerd
zijn in overeenstemming met de volgende
richtlijnen en standaards. Het technische
bestand is door de fabrikant samengesteld.
A presente assinatura serve para declarar
que os modelos supramencionados
são produtos em conformidade com as
seguintes directivas e normas. A cha
técnica é redigida pelo fabricante.
Niżej podpisany zaświadcza, że
wymieniony powyżej model produkowany
jest zgodnie z następującymi dyrektywami
i normami. Dokumenty techniczne zostały
przygotowane przez producenta.
Subsemnatul atest că modelul sus-
menţionat este produs în conformitate cu
următoarele directive şi standarde. Fişierul
tehnic este redactat de către producător.
Настоящим удостоверяется, что машина
вышеуказанной модели изготовлена
в соответствии со следующими
директивами и стандартами.
Техническая документация составлена
производителем.
Undertecknad intygar att ovannämnda
modell är producerad i överensstämmelse
med följande direktiv och standarder.
Den tekniska len är sammanställd av
tillverkaren.
Dolu podpísaný osvedčuje, že hore
uvedený model sa vyrába v súlade s
nasledujúcimi smernicami a normami.
Technický súbor vytvoril výrobca.
Spodaj podpisani potrjujem, da je zgoraj
omenjeni model izdelan v skladu z
naslednjimi smernicami in standardi.
Spis s tehnično dokumentacijo pripravi
izdelovalec.
Aşağıda İmzası olan kişi, yukarıda
bahsedilen model cihazın aşağıda verilen
direktiere ve standartlara uygunlukta imal
edildiğini onaylar. Teknik dosya üretici
tarafından derlenmiştir.
Модел / Model / Modell / Model / Modelo / Mudel / Modèle / Malli / Model
/ Μοντέλο / Modell / Model / Modello / Modelis / Modelis / Modell / Model
/ Modelo / Model / Model / Модель / Modell / Model / Model / Model : SW5500 - FLOORTEC R 985
Тип / Typ / Typ / Type / Tipo / Tüüp / Type / Tyyppi / Type / Τύπος /
Típus / Vrsta / Tipo / Tipas / Tips / Type / Type / Tipo / Typ / Tip / Тип /
Typ / Typ / Tip / Tip : SWEEPER
Сериен номер / Výrobní číslo / Seriennummer / Serienummer / Número de serie / Seerianumber / Numéro de série / Sarjanumero / Serial number /
Σειριακός αριθμός / Sorozatszám / Serijski broj / Numero di serie / Serijos numeris / Sērijas numurs / Serienummer / Serienummer / Número de série /
Numer seryjny / Număr de serie / Серийный номер / Serienummer / Výrobné číslo / Serijska številka / Seri Numarası :
Година на производство / Rok výroby / Baujahr / Fabrikationsår / Año de fabricación / Väljalaskeaasta / Année de fabrication / Valmistusvuosi / Year of
construction / Έτος κατασκευής / Gyártási év / Godina izgradnje / Anno di costruzione / Pagaminimo metai / Izgatavošanas gads / Byggeår / Bauwjaar /
Ano de fabrico / Rok produkcji / Anul fabricaţiei / Год выпуска / Tillverkningsår / Rok výroby / Leto izdelave / Leto izdelave/İmal yılı :

INSTRUCTIONS FOR USE ENGLISH
1466465000 - SW5500, FLOORTEC R 985 1
03/2016
TABLE OF CONTENTS
INTRODUCTION.............................................................................................................................................................. 2
MANUAL PURPOSE AND CONTENTS .......................................................................................................................................... 2
TARGET........................................................................................................................................................................................... 2
HOW TO KEEP THIS MANUAL....................................................................................................................................................... 2
DECLARATION OF CONFORMITY ................................................................................................................................................ 2
IDENTIFICATION DATA................................................................................................................................................................... 2
OTHER REFERENCE MANUALS................................................................................................................................................... 2
SPARE PARTS AND MAINTENANCE............................................................................................................................................. 2
CHANGES AND IMPROVEMENTS ................................................................................................................................................ 2
OPERATION CAPABILITIES ........................................................................................................................................................... 3
CONVENTIONS .............................................................................................................................................................................. 3
UNPACKING/DELIVERY ................................................................................................................................................. 3
SAFETY ........................................................................................................................................................................... 3
VISIBLE SYMBOLS ON THE MACHINE......................................................................................................................................... 3
SYMBOLS THAT APPEAR ON THIS MANUAL............................................................................................................................... 4
GENERAL INSTRUCTIONS............................................................................................................................................................ 4
MACHINE DESCRIPTION ............................................................................................................................................... 6
MACHINE STRUCTURE ................................................................................................................................................................. 6
CONTROL PANEL........................................................................................................................................................................... 9
ACCESSORIES/OPTIONS............................................................................................................................................................ 10
TECHNICAL DATA......................................................................................................................................................................... 10
WIRING DIAGRAM........................................................................................................................................................................ 12
USE ................................................................................................................................................................................ 14
BATTERY CHECK/SETTING ON A NEW MACHINE .................................................................................................................... 14
BEFORE MACHINE START-UP.................................................................................................................................................... 14
STARTING AND STOPPING THE MACHINE ............................................................................................................................... 15
PARKING BRAKE.......................................................................................................................................................................... 16
MACHINE OPERATION ................................................................................................................................................................ 16
HOPPER DUMPING...................................................................................................................................................................... 17
AFTER USING THE MACHINE..................................................................................................................................................... 18
MACHINE LONG INACTIVITY ...................................................................................................................................................... 18
MAINTENANCE............................................................................................................................................................. 18
SCHEDULED MAINTENANCE TABLE ......................................................................................................................................... 19
BATTERY INSTALLATION/REMOVAL AND BATTERY TYPE SETTING (WET OR GEL-AGM)................................................... 20
BATTERY CHARGING .................................................................................................................................................................. 21
MULTIFUNCTION DISPLAY SERVICE SCREENS....................................................................................................................... 22
MAIN BROOM HEIGHT CHECK AND ADJUSTMENT.................................................................................................................. 24
MAIN BROOM REPLACEMENT ................................................................................................................................................... 25
SIDE BROOM HEIGHT CHECK AND ADJUSTMENT .................................................................................................................. 26
SIDE BROOM REPLACEMENT.................................................................................................................................................... 27
PANEL DUST FILTER CLEANING AND INTEGRITY CHECK ...................................................................................................... 28
SKIRT HEIGHT AND OPERATION CHECK .................................................................................................................................. 29
DUSTGUARD™ SYSTEM WATER FILTER CLEANING (OPTIONAL)......................................................................................... 30
HYDRAULIC SYSTEM OIL LEVEL CHECK ................................................................................................................................. 30
FUSE CHECK/REPLACEMENT.................................................................................................................................................... 31
SAFETY FUNCTIONS ................................................................................................................................................... 31
EMERGENCY PUSH-BUTTON..................................................................................................................................................... 31
DRIVER’S SEAT MICROSWITCH................................................................................................................................................. 31
ANTI-SKID SAFETY SYSTEM ...................................................................................................................................................... 31
MACHINE ANGLE SENSOR ......................................................................................................................................................... 31
HOPPER POSITION SENSOR ..................................................................................................................................................... 31
HOPPER SAFETY VALVE............................................................................................................................................................. 31
TROUBLESHOOTING................................................................................................................................................... 32
SCRAPPING .................................................................................................................................................................. 33

ENGLISH INSTRUCTIONS FOR USE
2SW5500, FLOORTEC R 985 - 1466465000 03/2016
INTRODUCTION
NOTE
The numbers in brackets refer to the components shown in Machine Description chapter.
MANUAL PURPOSE AND CONTENTS
The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and
autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal.
Before performing any procedure on the machine, the operators and qualied technicians must read this Manual carefully. Contact
Nilsk in case of doubts concerning the interpretation of the instructions and for any further information.
TARGET
This Manual is intended for operators and technicians qualied to perform the machine maintenance.
The operators must not perform procedures reserved for qualied technicians. Nilsk will not be responsible for damages coming
from failure to follow these instructions.
HOW TO KEEP THIS MANUAL
The Instructions for Use Manual must be kept near the machine, inside an adequate case, away from liquids and other substances
that can cause damage to it.
DECLARATION OF CONFORMITY
The Declaration of Conformity, supplied with the machine, certies the machine conformity with the law in force.
NOTE
Two copies of the original declaration of conformity are provided together with the machine documentation.
IDENTIFICATION DATA
The machine serial number and model name are marked on the plate (30).
Product code and year of production are marked on the same plate.
This information is useful when requiring machine spare parts. Use the following table to write down the machine identication data.
MACHINE model ...............................................................................
PRODUCT code ................................................................................
MACHINE serial number ...................................................................
OTHER REFERENCE MANUALS
– Electronic Battery Charger Manual (to be considered as integral part of this Manual)
Moreover, the following Manuals are available:
– Spare Parts List (supplied with the machine)
– Service Manual (that can be consulted at Nilsk Service Centers)
SPARE PARTS AND MAINTENANCE
All necessary operating, maintenance and repair procedures must be performed by qualied personnel or by Nilsk Service
Centers. Only original spare parts and accessories must be used.
Contact Nilsk for service or to order spare parts and accessories, specifying the machine model, product code and serial number.
CHANGES AND IMPROVEMENTS
Nilsk constantly improves its products and reserves the right to make changes and improvements at its discretion without being
obliged to apply such benets to the machines that were previously sold.
Any change and/or addition of accessory must be approved and performed by Nilsk.

INSTRUCTIONS FOR USE ENGLISH
1466465000 - SW5500, FLOORTEC R 985 3
03/2016
OPERATION CAPABILITIES
This sweeper has been approved to clean (sweeping and vacuuming) compact and solid oors, in civil and industrial environments,
under safe operation conditions by a qualied operator.
CONVENTIONS
Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say on the driver’s seat
(3).
UNPACKING/DELIVERY
CAUTION!
To unpack the machine, carefully follow the instructions on the packing.
Upon delivery carefully check that the machine and its packing have not been damaged during transportation. In case of visible
damages, keep the packing and have it checked by the carrier that delivered it. Call the carrier immediately to ll in a damage claim.
Check that the machine is equipped with the following features:
– Technical documents:
• Sweeper Instructions for Use Manual (this document)
• Electronic Battery Charger Manual (if equipped)
• Sweeper Spare Parts List
– No. 1 10 A fuse
– No. 1 battery charger connector
SAFETY
The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary
precautions to safeguard people and property.
The operator’s cooperation is essential in order to prevent injury. No accident prevention program is effective without the total
cooperation of the person responsible for the machine operation. Most of the accidents that may occur in a factory, while working
or moving around, are caused by failure to comply with the simplest rules for exercising prudence. A careful and prudent operator is
the best guarantee against accidents and is essential for successful completion of any prevention program.
VISIBLE SYMBOLS ON THE MACHINE
WARNING!
Carefully read all the instructions before performing any operation on the machine.
WARNING!
Do not wash the machine with direct or pressurised water jets.
X
%
WARNING!
Do not use the machine on slopes with a gradient exceeding the specications.
WARNING!
Moving parts.
WARNING!
Moving parts. Danger of crushing.
WARNING!
Parts under voltage. Presence of corrosive uids.

ENGLISH INSTRUCTIONS FOR USE
4SW5500, FLOORTEC R 985 - 1466465000 03/2016
SYMBOLS THAT APPEAR ON THIS MANUAL
DANGER!
It indicates a dangerous situation with risk of death for the operator.
WARNING!
It indicates a potential risk of injury for people or damage to objects.
CAUTION!
It indicates a caution or a remark related to important or useful functions. Pay careful attention to the
paragraphs marked by this symbol.
NOTE
It indicates a remark related to important or useful functions.
CONSULTATION
It indicates the necessity to refer to the Instructions for use Manual before performing any procedure.
GENERAL INSTRUCTIONS
Specic warnings and cautions to inform about potential damages to people and machine are shown below.
DANGER!
–Before performing any maintenance, repair, cleaning or replacement procedure disconnect the battery
connector, remove the ignition key and engage the parking brake.
–This machine must be used by properly trained operators only.
–Sharp turns must be made in safe conditions. Avoid abrupt turns, particularly on slopes, and turns with the
hopper lifted.
–Do not lift the hopper when the machine is on a slope.
–Keep the batteries away from sparks, ames and incandescent material. Explosive gases are released when
charging the batteries.
–Do not wear jewels when working near electrical components.
–Do not work under the lifted machine without supporting it with safety stands.
–When working under the open hood, ensure that it cannot be closed by accident.
–Do not operate the machine near toxic, dangerous, ammable and/or explosive powders, liquids or
vapours: This machine is not suitable for collecting dangerous powders.
–If the machine is equipped with lead (WET) batteries, battery charging produces highly explosive hydrogen
gas. Keep the hood open when charging the batteries and perform this procedure in well-ventilated areas
and away from naked ames.
–When lead batteries (WET) are installed, do not tilt the machine for more than 30° from the horizontal plane
to prevent the highly corrosive acid from leaking out of the batteries. When the machine is to be tilted to
perform maintenance procedures, remove the batteries.
WARNING!
–Carefully read all the instructions before performing any maintenance/repair procedure.
–When working near the hydraulic system, always wear protective clothes and safety glasses.
–Do not close a door on the battery charger cable, or pull the battery charger cable around sharp edges or
corners. Do not run the machine on the battery charger cable.
–Before using the on board battery charger (optional), ensure that frequency and voltage values, indicated
on the battery charger plate, match the electrical mains voltage.
–Keep the battery charger cable away from heated surfaces.
–Do not use the machine if the battery charger cable or plug is damaged.
–Before performing any maintenance procedure, disconnect the battery charger cable from the electrical
mains to avoid any risk of re, electric shock or injuries.
–Do not smoke while charging the batteries.

INSTRUCTIONS FOR USE ENGLISH
1466465000 - SW5500, FLOORTEC R 985 5
03/2016
WARNING!
–This machine is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the machine by a person responsible for they safety.
Children should be supervised to ensure that they do not play with the machine.
–Close attention is necessary when used near children.
–Use only as shown in this Manual. Use only Nilsk’s recommended accessories.
–Check the machine carefully before each use, always check that all the components have been assembled
before use. If the machine is not perfectly assembled it can cause damages to people and properties.
–Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine
moving parts.
–To avoid any unauthorised use of the machine, remove the ignition key.
–Do not leave the machine unattended without being sure that it cannot move independently.
–Do not use the machine on slopes with a gradient exceeding the specications.
–Do not tilt the machine more than the angle indicated on the machine itself, in order to prevent instability.
–Use only brooms supplied with the machine or those specied in the Instructions for Use Manual. Using
other brooms could reduce safety.
–This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
–Before using the machine, close all doors and/or covers as shown in the Instructions for Use Manual.
–Do not wash the machine with direct or pressurised water jets, or with corrosive substances.
–Use the machine only where a proper lighting is provided.
–Working light (optional) has to be used only to enhance visibility on the oor to be cleaned, but it does not
authorize anyone to use the sweeper in dark environments.
–While using this machine, take care not to cause damage to people or objects.
–Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.
–Do not lean liquid containers on the machine, use the relevant can holder.
–The storage temperature must be between 0 °C and +40 °C.
–The machine working temperature must be between 0 °C and +40 °C.
–The humidity must be between 30 % and 95 %.
–Always protect the machine against the sun, rain and bad weather, both under operation and inactivity
condition. Store the machine indoors, in a dry place. (if applicable) This machine must be used in dry
conditions, it must not be used or kept outdoors in wet conditions.
–Do not use the machine as a means of transport, or for pushing/towing.
–The machine maximum capacity, operator’s weight not included, is 240 kg (the weight of waste).
–In case of re, use a powder re extinguisher, not a water one.
–Adjust the operation speed to suit the oor conditions.
–Avoid sudden stops when the machine is going downhill. Avoid sharp turns. Drive at slow speed when
going downhill.
–This machine cannot be used on roads or public streets.
–Do not tamper with the machine safety guards.
–Follow the routine maintenance procedures scrupulously.
–Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged.
Always keep the openings free from dust, hairs and any other foreign material which could reduce the air
ow.
–(Only for versions equipped with DustGuard™ system). Pay attention during machine transportation
when temperature is below freezing point. The water in the tank or in the hoses could freeze and seriously
damage the machine.
–Do not remove or modify the plates afxed to the machine.
–When the machine is to be pushed for service reasons (missing or discharged batteries, etc.), the speed
must not exceed 4 km/h.
–In case of machine malfunctions, ensure that these are not due to lack of maintenance. If necessary,
request assistance from the authorised personnel or from an authorised Service Center.
–If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer.
–To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of
this Manual, must be performed by the authorised personnel or by an authorised Service Center.
–The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries,
oils, etc.), which are subject to standards that require disposal in special centres (see the Scrapping
chapter).

ENGLISH INSTRUCTIONS FOR USE
6SW5500, FLOORTEC R 985 - 1466465000 03/2016
Guide lines to bacteria control and other dangers coming from the presence of microbes in the DustGuard™
system (optional).
WARNING!
To prevent the operators and other people from developing infections caused by microbes and Legionella that
may ourish in the dust guard system, take the following precautions:
–If possible, ll the tank with cold water (< 20 °C).
–DO NOT use stagnant water to ll the tank.
–DO NOT use recycled water, undrinkable water or water that has been in contact with the soil.
–Adjust and turn the nozzles towards the oor only, from preventing possible inhaling.
–Do not store the machine outdoors or near sources of heat.
–Do not over-ll the tank. Fill the tank sufciently so that it can be emptied by using the system.
–Empty the tank every 10 hours or once a week, according to the use.
–If the machine is not used for more than one week, empty the tank completely, and let it dry before storing
it.
–If the tank cannot be cleaned regularly, consider using a biocide that can kill or exert a controlling effect on
Legionella bacteria. Biocide must be chosen according to the local regulations and must be used according
to the relevant instructions and cautions, to avoid that the personnel gets affected by dangerous chemical
substances.
–If chemical products have to be used in the water tank, it is mandatory to apply the relevant information and
caution labels of the product.
MACHINE DESCRIPTION
MACHINE STRUCTURE
1. Steering wheel
2. Control panel (see the following paragraph)
3. Driver’s seat with safety microswitch
4. Seat position adjusting lever
5. Accelerator pedal
6. Service brake pedal
7. Parking brake lever: press both the service brake (6) and
the lever (7) to switch from the service brake to the parking
brake
8. Front skirt lifting pedal
9. Main broom height adjusting knob:
• Turn it counter-clockwise to increase the broom
pressure on the oor
• Turn it clockwise to decrease the broom pressure on
the oor
10. Vacuum system rear hood
11. Vacuum system hood release lever
12. Hopper (empty it when it is full)
13. Right door (to be opened for performing maintenance
procedures only)
14. Left door (for main broom removal)
15. Right side broom
16. Left side broom (optional)
17. Side broom guards (optional)
18. Main broom
19. Battery compartment hood
20. Can holder
21. Rear wheels
22. Front driving and steering wheel
23. Dust lter container / Dust guard system water tank
(optional)
24. Panel lter
25. Dust guard system water ller neck plug (optional)
26. Dust guard system nozzles (optional)
27. Front column
28. Working light (optional)
29. Flashing light (always on when the ignition key is turned to
“I”)
30. Serial number/technical data/conformity certication plate
31. Removable right side panel
32. Removable left side panel
33. Anchoring slots for transport (not for lifting)

INSTRUCTIONS FOR USE ENGLISH
1466465000 - SW5500, FLOORTEC R 985 7
03/2016
MACHINE STRUCTURE (Continues)
17
5
27
1
20
3
30
19
21
6
7
8
14
10
24
25
12
18
13
9
4
29
32
2
5
31
15
28
22
26
16
11
23
33
P100891

ENGLISH INSTRUCTIONS FOR USE
8SW5500, FLOORTEC R 985 - 1466465000 03/2016
MACHINE STRUCTURE (Continues)
41. Battery compartment hood (open)
42. Lead batteries (WET) or gel batteries (GEL-AGM)
43. Battery caps (for WET batteries only)
44. Battery connection diagrams
45. Battery connector
46. Hydraulic unit with tank for hopper lifting
47. Open hood safety rod
48. Electronic battery charger (optional)
BATTERY
PLUG
44
6V
6V
6V
6V
BATTERY
PLUG
24V
41
47
48
46 45
43
42
P100892