Nobles Power Eagle 716 608543 Product manual

R
Operator and Parts Manual
Self-Contained Carpet Extractor
Power Eaglet716
Model No.:
608543
608548
Rev. 02 (08-05)

OPERATION
2Power Eaglet716 (08--05)
This manual is furnished with each new model. It
provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
Use the illustrated Parts Lists to order parts. Before
ordering parts or supplies, be sure to have your
machine model number and serial number handy.
Parts and supplies may be ordered by phone or mail
from any authorized parts and service center,
distributor or from any of the manufacturer’s
subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
maintenance instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,
old machine components such as
batteries, hazardous fluids such as
antifreeze and oil, in a safe
environmentally way according to your
local waste disposal regulations.
Always remember to recycle.
Tennant Company
PO Box 1452
Minneapolis, MN 55440
Phone: [phone] or (763) 513--2850
www.nobles.com
Nobles, the Nobles logo and Power Eagle are registered United States
trademarks of Tennant Company.
Specifications and parts are subject to change without notice.
Copyright E1999, 2000, 2005 Tennant Company. All rights reserved.
MACHINE DATA
Please fill out at time of installation for future reference.
Model No.-
Install. Date -
Serial No.-

OPERATION
Power Eaglet716 (08--05) 3
TABLE OF CONTENTS
SAFETY PRECAUTIONS 4....................
GROUNDING INSTRUCTIONS 5...........
SAFETY LABELS 6...........................
MACHINE COMPONENTS 7...................
MACHINE SETUP 8..........................
MACHINE OPERATION 8.....................
PRE--OPERATION 8.......................
CLEANING CARPETS 9...................
WHILE OPERATING 9.....................
OPERATING ACCESSORY TOOLS
(OPTIONAL) 10............................
ADJUSTING BRUSH HEIGHT 10................
DRAINING TANKS 10..........................
DRAINING RECOVERY TANK 10............
DRAINING LEFTOVER CLEANING
SOLUTION 11.............................
MACHINE MAINTENANCE 11..................
DAILY MAINTENANCE 11...................
MONTHLY MAINTENANCE 12...............
SERVICING MACHINE: 12..................
STORING MACHINE 12........................
RECOMMENDED STOCK ITEMS 12.............
TROUBLE SHOOTING 13......................
SPECIFICATIONS 14..........................
MACHINE DIMENSIONS 14....................
ELECTRICAL DIAGRAMS 15...................
PARTS LIST 16...............................
TANK GROUP 16..........................
CONTROL CONSOLE GROUP 18...........
CHASSIS GROUP 20.......................
BRUSH GROUP 22.........................
PUMP BREAKDOWN 24....................
OPTIONS 25..................................
127 mm (5 in) HAND TOOL 25...............
76 mm (3 in) CREVICE TOOL 25.............
LOW PRESSURE UPHOLSTERY TOOL 26...
SOLUTION AND VACUUM HOSES 27........
PUMP--UP CARPET SPRAYER 27...........
HARD FLOOR SQUEEGEE ASSEMBLY 27...
FLOOR TOOL, LOW PRESSURE
330 mm (13 in) 28..........................
FLOOR TOOL, LOW PRESSURE
406 mm (16 in) 30..........................

OPERATION
4Power Eaglet716 (08--05)
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is
designed exclusively to clean carpet and
upholstery in an indoor environment and is not
constructed for any other use. Use only
recommended accessory tools and commercially
available carpet cleaners intended for machine
application.
All operators must read, understand and practice
the following safety precautions.
The following warning alert symbol and the “FOR
SAFETY” heading are used throughout this manual as
indicated in their description:
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
Failure to follow these warnings may result in
personal injury, electrical shock, fire or explosion.
WARNING: Fire Or Explosion Hazard:
-- Never Use Flammable Liquids Or Operate
Machine in Or Near Flammable Liquids,
Vapors Or Combustible Dusts.
This machine is not equipped with explosion proof
motors. The electric motors will spark upon start
up and during operation which could cause a flash
fire or explosion if machine is used in an area
where flammable vapors/liquids or combustible
dusts are present.
-- Do Not Pick Up Flammable Materials Or
Reactive Metals.
WARNING: Electrical Hazard. Do Not Operate
With Damaged Power Cord. Do Not Modify Plug.
Unplug power Cord Before Servicing Machine.
If the supply cord is damaged or broken, it must
be replaced by the manufacturer or it’s service
agent or a similarly qualified person in order to
avoid a hazard.
WARNING: Spinning Brush. Keep Hands
Away. Turn Off Power Before Working On
Machine.
WARNING: Electrical Shock Hazard.
Do Not Use Outdoors. Do Not Expose To Rain.
Store Indoors.
The following information signals potentially
dangerous conditions to the operator or
equipment:
FOR SAFETY:
1. Do not operate machine:
-- With flammable liquids or near flammable
vapors as an explosion or flash fire may
occur.
-- Unless trained and authorized.
-- Unless operator manual is read and
understood.
-- Unless cord is properly grounded.
-- With damaged cord or plug.
-- If not in proper operating condition.
-- In outdoor areas.
-- In standing water.
-- With the use of additional extension cords.
Only use manufacturer’s extension cord
equipped with machine which has proper
capacity and is grounded.
2. Before operating machine:
-- Make sure all safety devices are in place
and operate properly.
-- Place wet floor signs as needed.
3. When using machine:
-- Do not run machine over cord.
-- Do not pull machine by plug or cord.
-- Do not pull cord around sharp edges or
corners.
-- Do not unplug by pulling on cord.
-- Do not stretch cord.
-- Do not handle plug with wet hands.
-- Keep cord away from heated surfaces.
-- Report machine damage or faulty
operation immediately.
-- Follow mixing and handling instructions
on chemical containers
-- Never allow children to play on or around.
4. Before leaving or servicing machine:
-- Turn off machine.
-- Unplug cord from wall outlet.

OPERATION
Power Eaglet716 (08--05) 5
5. When servicing machine:
-- Unplug cord from wall outlet.
-- Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves.
-- Use manufacturer supplied or approved
replacement parts.
-- All repairs must be performed by a
qualified service person.
-- Do not modify the machine from its
original design.
6. When transporting machine:
-- Get assistance when lifting machine.
-- Unplug cord from wall outlet.
-- Use tie--down straps to secure machine to
truck or trailer.
GROUNDING INSTRUCTIONS
Machine must be grounded. If it should
malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment--grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.
Grounded
3HoleOutlet
Ground Pin

OPERATION
6Power Eaglet716 (08--05)
SAFETY LABELS
The safety label appears on the machine in the location indicated. Replace label if it is missing or becomes damaged
or illegible.
WARNING LABEL -- Located on back of control
console.

OPERATION
Power Eaglet716 (08--05) 7
MACHINE COMPONENTS
7
3
1
2
5
4
6
9
18
12
17
16
10 11
8
14
13
19
15
1. Recovery Tank Dome
2. Pick-up Vacuum Hose
3. Solution Tank Dust Cover
4. Brush Height Ajustment Knob
5. Brush Housing
6. Vacuum Pick-up Head
7. Extension Power Cord
8. Cord Strain-Relief Clip (Belt)
9. 254 mm (10 in) Stair Climbing Wheels
10. Master Switch (Vacuum and Pump)
11. Carpet Cleaning Button (Brush)
12. Spray Bar
13. Pump Circuitbreaker
14. Brush Circuitbreaker
15. Vacuum Circuitbreaker
16. Power Cord Pigtail
17. Drain Valve T--Handle
18. Recovery Tank Drain Spout
19. Accessory Tool Solution Hose Quick Coupler

OPERATION
8Power Eaglet716 (08--05)
MACHINE SETUP
1. Carefully check carton for signs of damage.
Report damages at once to carrier. The machine
is shipped fully assembled and is ready for
operation.
2. Fill solution tank with 30.8L (7 gal) of hot water,
60°C (140°F) maximum (Figure 1).
NOTE: The water must not be hotter than 60_C
(140_F) or tank damage may occur.
NOTE: Use different buckets to fill and drain machine
to prevent solution system clogs.
FIG. 1
WARNING: Fire or Explosion Hazard. Never
Use Flammable Liquids.
3. Add a recommended cleaning solution. Follow
bottle’s mixing instructions.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
ATTENTION: If using powdered cleaning
chemicals, mix prior to adding.
NOTE: If desired, hot water alone achieves excellent
cleaning results.
4. Close lid after filling.
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
WARNING: Fire Or Explosion Hazard. Never
Use Flammable Liquids Or Operate Machine in Or
Near Flammable Liquids, Vapors Or Combustible
Dusts.
PRE--OPERATION
1. Vacuum carpet to remove particles and other
debris.
2. Inspect power cord for damage.
WARNING: Electrical Hazard. Do Not Operate
With Damaged Power Cord. Do Not Modify Plug.
Unplug power Cord Before Servicing Machine.
If the supply cord is damaged or broken, it must
be replaced by the manufacturer or it’s service
agent or a similarly qualified person in order to
avoid a hazard.
3. Plug power cord into a grounded wall outlet
(Figure 2).
Grounded
3HoleOutlet
Ground Pin
FIG. 2
FOR SAFETY: Do not operate machine with the
use of additional extension cords. Only use
manufacturer’s extension cord equipped with
machine which has proper capacity and is
grounded.

OPERATION
Power Eaglet716 (08--05) 9
CLEANING CARPETS
1. Turn on Master switch (Figure 3).
FIG. 3
2. Press and hold in Carpet Cleaning button. Pull
machine towards you, 1219 mm (4 ft) at a time.
For best cleaning results, lift machine handle
slightly while pulling backward. This transfers
weight of machine to the pickup head for best
water recovery (Figure 4).
FIG. 4
3. At end of path, release Carpet Cleaning button,
pull machine towards you another 305 mm (1 ft) to
vacuum excess spray. Push down on handle and
move to next area to be cleaned. Overlap each
pathby50mm(2in).
WARNING: Fire Or Explosion Hazard. Do Not
Pick Up Flammable Materials Or Reactive Metals.
WHILE OPERATING
1. If necessary, adjust brush height to accommodate
type of carpet (See ADJUSTING BRUSH
HEIGHT).
2. Work away from wall outlet and power cord to
prevent cord damage.
3. Check for excessive foam buildup in recovery
tank. Use a recommended foam control solution to
prevent motor damage (Figure 5).
FIG. 5
ATTENTION: Do not allow foam to enter vacuum
screen. Damage to vacuum will result. This
damage is not covered by warranty.
4. If brush or vacuum motor should stop, circuit
breaker may have tripped. Turn off machine,
unplug power cord and check for any obstructions.
Let motor cool and manually reset circuit breaker
button, located on bottom of switchbox
(Figure 6).
FIG. 6
WARNING: Electrical Hazard. Unplug power
Cord Before Servicing Machine.
WARNING: Spinning Brush. Keep Hands
Away. Turn Off Power Before Working On
Machine.

OPERATION
10 Power Eaglet716 (08--05)
5. After cleaning, perform the daily maintenance
procedures.
NOTE: Allow up to one hour for carpet to dry. Use air
movers to reduce drying time.
OPERATING ACCESSORY TOOLS (OPTIONAL)
1. Disconnect vacuum hose from recovery dome and
connect accessory vacuum hose (Figure 7).
2. Connect accessory solution hose to quick coupler,
located at rear of machine (Figure 7).
FIG. 7
3. Attach desired accessory tool to hoses.
4. Turn on Master switch.
5. Begin operating accessory tool (Figure 8).
FIG. 8
WARNING: Fire Or Explosion Hazard. Do Not
Pick Up Flammable Materials Or Reactive Metals.
NOTE: When cleaning upholstery, always check
cleaning instructions sewn in furniture by
manufacturer.
6. After operating accessory tool, relieve water
pressure from tool before disconnecting hose.
Squeeze trigger for five seconds after turning off
switches.
ADJUSTING BRUSH HEIGHT
1. Turn off machine and unplug power cord from wall
outlet.
WARNING: Electrical Hazard. Unplug power
Cord Before Servicing Machine.
WARNING: Spinning Brush. Keep Hands
Away. Turn Off Power Before Working On
Machine.
2. Adjust brush to proper height. Turn height
adjustment knob until bristles slightly touch carpet,
then turn knob another half turn. Turn knob
clockwise to raise and counterclockwise to lower
(Figure 9).
FIG. 9
DRAINING TANKS
WARNING: Electrical Hazard. Unplug power
Cord Before Servicing Machine.
NOTE: Use different buckets to fill and drain machine
to prevent solution system clogs.
DRAINING RECOVERY TANK
1. When solution tank runs dry, recovery tank must
be emptied. To empty recovery tank, turn off
machine and position a discharge bucket under
drain valve down spout.
NOTE: Use different buckets to fill and drain machine
to prevent solution system clogs.

OPERATION
Power Eaglet716 (08--05) 11
2. Pull valve T--handle to empty dirty water
(Figure 10).
FIG. 10
3. Close valve before continuing operation.
DRAINING LEFTOVER CLEANING SOLUTION
1. When finished cleaning, use clean-out hose to
vacuum remaining water from solution tank.
Attach one end to recovery dome. Turn on Master
switch and use other end to vacuum water
(Figure 11).
FIG. 11
MACHINE MAINTENANCE
To keep machine in good working condition, simply
follow machine’s daily and monthly maintenance
procedures.
WARNING: Electrical Hazard. Unplug power
Cord Before Servicing Machine.
Contact an Authorized Service Center for machine
repairs.
FOR SAFETY: When servicing machine, all repairs
must be performed by a qualified service person.
DAILY MAINTENANCE
(After Every Use)
1. Drain and rinse out tanks thoroughly (See Draining
Tanks).
2. Rinse out recovery tank and recovery dome
thoroughly after every use.
3. Remove vacuum screen and clean (Figure 12).
FIG. 12
4. Remove and rinse off the two tank screens
located in the bottom of the solution tank.
5. Remove any entangled carpet fibers and debris in
brush.
6. Remove any clogged debris in vacuum head.
7. Check power cord for damage, replace if
necessary. Coil cord neatly after each use.
If the supply cord is damaged or broken, it must
be replaced by the manufacturer or it’s service
agent or a similarly qualified person in order to
avoid a hazard.
8. Inspect spray pattern for plugging. If plugged,
remove spray tips and soak in acetic acid solution
for up to six hours. Do not use pointed objects to
unplug tips, damage will occur.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
9. Clean machine with a nonabrasive, nonsolvent
cleaner.
ATTENTION: Do not power spray or hose off
machine. Electrical component damage may
result.

OPERATION
12 Power Eaglet716 (08--05)
MONTHLY MAINTENANCE
(Every80HoursofUse)
1. Flush pump system with an acetic acid solution to
dissolve normal alkaline chemical buildup. Follow
instructions below:
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
a. Premix .5 L (16 oz) of an acetic acid solution
with 7.5 L (2 gal) of hot water, 60_C (140_F)
maximum, and pour into solution tank.
NOTE: The water must not be hotter than 60_C
(140_F) or tank damage may occur.
NOTE: If filling with a bucket be certain that bucket is
clean. This will prevent possible solution line clogs.
b. Turn on Vacuum/Pump switch.
c. Position brush/vacuum head over floor drain
and operate machine for one minute.
d. Turn off machine and allow remaining solution
to break down alkaline buildup overnight.
e. Next day, spray out remaining solution and
flush system with 11 L (3 gal) of clean water.
2. Lubricate wheels with a water resistant oil.
3. Inspect machine for water leaks.
4. Inspect machine for loose screws.
SERVICING MACHINE:
For ease of servicing, the machine’s tanks are hinged
to pivot away from metal chassis to allow access to
inner components.
ATTENTION: Make sure tanks are empty before
opening.
1. Remove two rear hex--head screws, located under
chassis rear wheels.
2. Remove two allen head screws.
3. Remove two remaining hex--head screws located
at front of chassis.
4. Lift tanks upward, away from chassis. The
vacuum tool will pivot upward with tanks.
STORING MACHINE
1. Before storing machine, be certain to flush tanks
and drain machine of all water.
2. Store machine in a dry area in the upright position
with brush raised off floor.
3. Remove recovery dome to promote air circulation.
ATTENTION: If storing machine in freezing
temperatures, be sure that machine, pump and
spraying system are completely drained and dry.
Damage due to freezing temperatures is not
covered by warranty.
WARNING: Electrical Shock Hazard.
Do Not Use Outdoors. Do Not Expose To Rain.
Store Indoors.
RECOMMENDED STOCK ITEMS
Refer to the Parts List Manual for recommended stock
items. Stock Items are clearly identified with a bullet
preceding the parts description. See example below:

OPERATION
Power Eaglet716 (05--99) 13
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
Machine does not operate. Faulty switches or wiring. Contact Service Center.
p
Faulty power cord. Contact Service Center.
Building circuit breaker tripped. Reset breaker.
Solution pump does not operate. Overheated pump. Determine cause and wait 20 minutes
for pump to cool. Reset breaker.
Faulty solution pump. Contact Service Center.
Faulty solenoid. Contact Service Center.
Faulty switch. Contact Service Center.
Loose or broken wiring. Contact Service Center.
Vacuum motor does not operate. Vacuum motor thermal overload
tripped.
Check air flow for obstruction, wait 20
minutes for motor to cool.
Vacuum motor circuit breaker tripped. Reset breaker.
Loose or broken wiring. Contact Service Center.
Faulty Master switch. Contact Service Center.
Defective vacuum motor. Contact Service Center.
Worn carbon brushes. Replace brushes or call for service.
Brush motor does not operate. Brush motor circuit breaker tripped. Remove brush obstruction OR
readjust brush height. Reset brush
breaker button at bottom of switch
box.
Carpet Cleaning Switch not pushed. Push Carpet Cleaning Switch.
Faulty brush motor. Contact Service Center.
Loose or broken brush belt. Contact Service Center.
Faulty switch or wiring. Contact Service Center.
Poor pick up. Open drain valve. Close valve.
p
p
Clogged standpipe screen in recovery
tank.
Remove recovery dome and clean lint
off screen.
Air leakage around recovery dome. Tighten recovery dome knobs or
replace gaskets.
Loose vacuum hose connections. Secure connections.
Defective vacuum hose. Replace hose.
Loose vacuum hose cuffs. Secure cuffs to hose.
Pulling machine too fast. Slow down cleaning process.
Uneven or no spray. Dirty or plugged spray tips. Clean or replace tips.
p
y
Improper spray tip size or spray angle. Replace with proper tips.
Worn spray tips. Replace spray tips.
Solution tank low or empty. Refill solution tank.
Faulty solution pump. Contact Service Center.
Plugged solution tank filter. Clean filter.
Drain valve leaks. Drain valve gaskets worn. Replace gaskets.
Lint or dirt in drain valve. Clean valve.

OPERATION
14 Power Eaglet716 (08--05)
SPECIFICATIONS
Model Power Eaglet716
LENGTH 991 mm (39 in)
WIDTH 406 mm (16 in)
HEIGHT 864 mm (34 in)
WEIGHT 39 Kg (86lb)
SOLUTION TANK CAPACITY 31L (7 gal)
RECOVERY TANK CAPACITY 31L (7 gal)
CLEANING PATH WIDTH 406 mm (16 in)
MAXIMUM CLEANING RATE 186 m2(2,000 sq. ft) per hour
BRUSH MOTOR 120V, .1hp,1A, 120W, 1800 rpm
BRUSH SPEED 1200 rpm
SOLUTION PUMP 120V, 6.9bar (100psi), 1A
VACUUM MOTOR 120V, 1.66 hp, 10.3A, 1236W, 3 stage
SEALED WATER LIFT 2972 mm (117 in)
TOTAL POWER CONSUMPTION 120V, 12.7A, 1524W
DECIBEL RATING AT OPERATOR’S EAR,
INDOORS ON CARPET
>70dB(A)
MACHINE DIMENSIONS
864 mm
(34 in)
991 mm
(39 in)
406mm
(16 in)

ELECTRICAL DIAGRAMS
Power Eaglet716 (07--99) 15
PUSH BUTTON SWITCH
MASTER
SWITCH
POWER CORD
CONDUIT
SOLENOID
CORD 18/3
(Chassis to
Brush Housing)
SOLUTION
PUMP
AC
+
AC
PUMP
1.5 AMPS
BRUSH
1.5 AMPS
VACUUM
12 AMPS
BRUSH
MOTOR
VACUUM
MOTOR
WHT/ORG
BLK
RED
GRN
BLU
ORG WHT
WHT/ORG
WHT/RED WHT/BLK
BLU
RED
BLK
GRN
BLK
BLK
BLK
WHT
BLK
BLK
BLK
WHT
GRN
BLU
WHT
BLK
RED
GRN ORG
GRN
WHT
BLK
WHT/RED
WHT/BLK
RED BLK
WHT/GRN
GRN/YLW
GRN
GRN/YLW
GRN
WHT
BLK
WHT
BLK
120V WIRING DIAGRAM

PARTS LIST
Power Eaglet716 (08--05)
16
TANK GROUP
1
9
4
5
6
7
14
13 15
16
18
19 22
20 21
25
26
27
23
24
28
30
29
31
32
33
34
35
36
37
38
39
40
41
42
43
44
12
11
10
2
17
8
4
3

PARTS LIST
Power Eaglet716 (08--05) 17
TANK GROUP
REF PART # DESCRIPTION QTY.
1608544 TANK, SOLUTION, GREEN 1
2602505 LABEL, INSTRUCTIONS 1
∇3210231 DVALVE, WATER, GATE, 24PM W/
HANDLE
1
Y4210239 DSEAL, GATE DRAIN VALVE 2
Y5210237 DHANDLE, METAL -- DRAIN VALVE 1
6210232 DOWNSPOUT, DRAIN VALVE 1
7210234 DGASKET, DRAIN VALVE 1
8130040 TIE, CABLE, NYL 6.0L, .12W 2
9230500 COVER, DUST 1
10 120906 LABEL, IMPORTANT -- DRAIN 1
11 608185 LABEL, LOGO NOBLES 171 X 32
WHT
1
12 608471 LABEL, POWER EAGLE 716 2
13 700144 STANDPIPE ASSEMBLY 1
14 180612 DSCREEN, STANDPIPE 1
15 240217 DKNOB, RECOVERY DOME 2
16 100112 DOME, RECOVERY 1
17 120399 LABEL, DO NOT ALLOW FOAM 1
18 140037 WASHER, FLAT, 0.22B 0.44D .03 2
19 100042 GASKET, RECOVERY DOME 1
20 230159 DO--RING, STANDPIPE 1
21 608546 TANK, RECOVERY, GREEN 1
22 160421 HOSE, VACUUM, 1.5D X 19L,
2--CUFFS
1
∇23 160424 DHOSE, VACUUM 1.5D X 36L,
2--CUFFS (CLEANOUT)
1
Y24 160430 DHOSE CUFF, 1--1/2 X 1--1/2 2
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
25 101714 GASKET, WASTE CHAMBER 1
26 210240 NUT, HEX, FLNG 1--1/2 FPT METAL 1
27 140227 SCREW, STUD, 1/4--20 X 5 ZINC 4
28 210240 NUT, HEX, FLNG 1--1/2 FPT METAL 1
29 100037 GASKET, VACUUM MOTOR 1
30 230503 SHIELD, VACUUM MOTOR 1
∇31 130416 DFAN, VACUUM, 5.7D 3S 120V 1
Y190160 DCARBON BRUSH (2/PK) 2
32 230237 BRACKET, SUPPORT 1
33 41169 NUT, HEX, LOCK, .25--20, NL, SS 4
34 1022164 HOSE, EXHAUST, 2.0”ID, 26”LG 1
35 140308 CLAMP, HOSE 2
36 240194 DKNOB, HEIGHT ADJUSTMENT 1
37 230382 STUD, HEIGHT ADJUSTMENT 1
38 230638.BK BRACKET, HEIGHT ADJUSTMENT 1
39 140919 SPACER, NYLON 1
40 200450.BK TOOL, FLOOR, 16” BLACK 1
41 200956 DSHOE, 16” FLOOR TOOL 2
42 140313 CLAMP, FLOOR TOOL 2
43 140016 WASHER, LOCK 1/4” 4
44 140554 SCREW, HEX CAP 1/4--20 X 3/4 4

PARTS LIST
Power Eaglet716 (08--05)
18
CONTROL CONSOLE GROUP
19
5
6
7
8
1
14
16
11
12
13
10
21
11
4
2
3
17
18
20
9
15

PARTS LIST
Power Eaglet716 (08--05) 19
CONTROL CONSOLE GROUP
REF PART # DESCRIPTION QTY.
∇1612273 SWITCHBOX ASM, 120V BLK 1
Y611416 SWITCHBOX, SHALLOW RM--BLK
ONLY
1
Y2130304 DRECTIFIER, BRIDGE 600V 15AMP 1
Y3140336 NUT, HEX, 10--24 NY 1
Y4140335 SCREW, RND, 10--24 X 1 SLOT NY 1
Y5578337000AM DBREAKER, CIRCUIT, 1.5 AMP 2
Y6130441AM DSWITCH, PUSH MOMENTARY 1
Y7130717 DSWITCH, ROCKER ON/OFF 1
Y8613283 LABEL, WARNING AC WB SCRUB/
EXTR 6 X 2.125
1
Y9603829 LABEL, INSTR CLEAN ON/OFF
KEMA
1
10 140044 WASHER, 13/16 INT ZN 1
Y11 140504 NUT, LOCK CONDUIT 1/2 NPT 2
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
Y12 130670AM DBREAKER, CIRCUIT, 12 AMP 1
Y∇13 130977 DHARNESS, WIRING 1
Y14 130242 DFITTING, PLSTC, E90 PM08,
FLEXCON
1
Y15 130166 DGRIP, STRAIN--RELIEF W/NUT 1
Y16 130237 CORD, ASSY 14/3 X 18” YELLOW 1
Y17 140022 WASHER, INT 3/8 SS 3
Y18 612922 NUT, HEX PG--11 CORDGRIP
METAL
1
19 140889 SCREW, 1/4--20 X 3/4 4
20 130176 DCLIP, CORD STRAIN--RELIEF
YELLOW (BELT)
1
21 130250 DCORD, POWER16/3 X 50FT EXT
SJT YELLOW
1

PARTS LIST
Power Eaglet716 (08--05)
20
CHASSIS GROUP
8
52
53 54
8
9
9
10
1
23
45
6
7
11 12
11
15
14
13
17
16
14
13
18
19
20
12
21
21
2
23
22
24
24
27
28
24
29
24
30
24
27
26
25
26
25
10
33
32
31
34
35
36
37
38
39
40
38
39
40
38
39
40
41
42
43
45
44
34
35
36
47
46
38
39
40
48
50
51
49
38
39
40