Nobles Typhoon 16B 608817 Product manual

ENGLISH - ESPAÑOL
Operator and Parts Manual
Manual del Operador y Piezas
Wet/Dry Battery Vacuum
Batería en aspiración húmeda/seca
Typhoont16B
NOBLES CUSTOMER SERVICE:
1–800–365–6625
FAX: [phone]
TECHNICAL SUPPORT:
1–800–522–7839 EXT. 5356
TENNANT COMPANY
701 NORTH LILAC DRIVE
MINNEAPOLIS, MN 55422
MAILING ADDRESS:
TENNANT COMPANY
P.O. BOX 1452
MINNEAPOLIS, MN 55440–1452
Model No.:
608817
608818 – PAC
608819
Rev. 01 (10-03)

OPERATION
2Typhoont16B (10–03)
This manual is furnished with each new machine. It
provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
Use the illustrated Parts List to order replacement
parts. Before ordering parts or supplies, be sure to
have your machine model number and serial number
available. Parts and supplies may be ordered by
phone or mail from any authorized parts and service
center, distributor or from any of the manufacturer’s
subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
machine maintenance instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
MACHINE DATA
Pleasefill out at time of installation for future reference.
Model No.-
Install. Date -
Serial No.-
E1999, 2003 Tennant Company Printed in the U.S.A.
Nobles is a registered United States trademark of Tennant Company.
Typhoon is a United States trademark of Tennant Company.
TABLE OF CONTENTS
SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . . . . .
WARNING LABELS 4. . . . . . . . . . . . . . . . . . . . . . . . .
MACHINE COMPONENTS 5. . . . . . . . . . . . . . . . . . .
MACHINE INSTALLATION 6. . . . . . . . . . . . . . . . . . .
UNCRATING MACHINE 6. . . . . . . . . . . . . . . . . .
INSTALLING BATTERIES 6. . . . . . . . . . . . . . . .
ATTACHING OPTIONAL SQUEEGEE KIT 6. .
MACHINE SETUP 8. . . . . . . . . . . . . . . . . . . . . . . . . .
WET VACUUMING 8. . . . . . . . . . . . . . . . . . . . . .
DRY VACUUMING 8. . . . . . . . . . . . . . . . . . . . . . .
MACHINE OPERATION 8. . . . . . . . . . . . . . . . . . . . .
VACUUM MOTOR THERMAL PROTECTOR 8
OPERATING ACCESSORY TOOLS 9. . . . . . .
OPERATING SQUEEGEE KIT OPTION 9. . . .
DRAINING RECOVERY TANK 9. . . . . . . . . . . . . . . .
CHARGING BATTERIES 10. . . . . . . . . . . . . . . . . . . .
MACHINE MAINTENANCE 11. . . . . . . . . . . . . . . . . .
DAILY MAINTENANCE 11. . . . . . . . . . . . . . . . . . .
WEEKLY MAINTENANCE 11. . . . . . . . . . . . . . . .
MONTHLY MAINTENANCE 11. . . . . . . . . . . . . . .
QUARTERLY MAINTENANCE 11. . . . . . . . . . . .
BATTERY MAINTENANCE 12. . . . . . . . . . . . . . .
TRANSPORTING MACHINE 12. . . . . . . . . . . . . . . . .
STORING MACHINE 13. . . . . . . . . . . . . . . . . . . . . . . .
RECOMMENDED STOCK ITEMS 13. . . . . . . . . . . . .
TROUBLE SHOOTING 13. . . . . . . . . . . . . . . . . . . . . .
MACHINE SPECIFICATIONS 14. . . . . . . . . . . . . . . .
MACHINE DIMENSIONS 14. . . . . . . . . . . . . . . . . . . .
ELECTRICAL DIAGRAM 29. . . . . . . . . . . . . . . . . . . .
PARTS LIST 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TANK GROUP 30. . . . . . . . . . . . . . . . . . . . . . . . . .
BASE GROUP 32. . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SQUEEGEE KIT ASSEMBLY 34. . . . . . . . . . . . .
WET/DRY TOOL KIT 36. . . . . . . . . . . . . . . . . . . . .
DRY TOOL KIT 37. . . . . . . . . . . . . . . . . . . . . . . . . .
FLOOR & CARPET TOOL KIT 38. . . . . . . . . . . .
WET PICK–UP TOOL KIT 39. . . . . . . . . . . . . . . .

OPERATION
Typhoont16B (10–03) 3
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is
designed for wet/dry vacuuming in an indoor
environment and is not constructed for any other
use. Use only recommended accessory tools.
All operators must read, understand and practice
the following safety precautions.
The following warning alert symbol and the “FOR
SAFETY”heading are used throughout this manual as
indicated in their description:
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
Failure to follow these warnings may result in:
personal injury, electrocution, electrical shock,
fire or explosion.
WARNING: Do Not Operate Machine In Or
Near Flammable Liquids, Vapors Or Combustible
Dusts.
This machine is not equipped with an explosion
proof motor. The electric motor will spark upon
start up and during operation which could cause a
flash fire or explosion if machine is used in an
area where flammable vapors/liquids or
combustible dusts are present.
WARNING: Do Not Pick Up Flammable Or
Toxic Materials, Burning Or Smoking Debris.
WARNING: Keep Sparks And Open Flame
Away. Keep Battery Hood Open When Charging.
WARNING: Disconnect Battery Cables Before
Servicing Machine.
The following information signals potentially
dangerous conditions to the operator or
equipment:
FOR SAFETY:
1. Do not operate machine:
–With flammable liquids or near flammable
vapors as an explosion or flash fire may
occur.
–Unless trained and authorized.
–Unless operator manual is read and
understood.
–In standing water.
–If not in proper operating condition.
–Without bag and/or filters in place.
2. Before operating machine:
–Make sure all safety devices are in place
and operate properly.
3. When using machine:
–Do not pick up burning or smoking debris,
such as cigarettes, matches or hot ashes.
–Never allow children to play on or around.
–Report machine damage or faulty
operation immediately.
4. Before leaving or servicing machine:
–Stop on level surface.
–Turn machine off.
5. When servicing machine:
–Disconnect battery connections before
working on machine.
–Wear protective gloves and safety glasses
when handling batteries or battery cables.
–Avoid contact with battery acid.
–Use manufacturer supplied or approved
replacement parts.
–All repairs must be performed by a
qualified service person.
–Do not modify the machine from its
original design.
6. When transporting machine:
–Turn machine off.
–Do not lift machine when batteries are
installed.
–Get assistance when lifting machine.
–Use a recommended ramp when
loading/unloading into/off truck or trailer.
–Use tie–down straps to secure machine to
truck or trailer.

OPERATION
4Typhoont16B (10–03)
WARNING LABELS
The warning labels appear on the machine in the
locations indicated. Replace labels if they become
damaged or illegible.
WARNING LABEL –
LOCATED ON TOP OF MACHINE.
WARNING LABEL –
LOCATED ON BACK SIDE OF MACHINE.
FOR SAFETY LABEL –
LOCATED ON BACK
SIDE OF MACHINE.
FOR SAFETY:
Read the owner’s manual
before using machine.
WARNING: FAILURE TO
FOLLOW THESE WARNINGS
MAY RESULT IN: PERSONAL
INJURY, ELECTROCUTION,
ELECTRICAL SHOCK, FIRE
OR EXPLOSION.
Do Not Operate Machine In
Or Near Flammable Liquids,
Vapors Or Combustible
Dusts.
Do Not Pick Up Flammable
Or Toxic Materials, Burning
Or Smoking Debris.

OPERATION
Typhoont16B (10–03) 5
MACHINE COMPONENTS
5
89
6
4
7
1
32
1. Bag Compartment Cover
2. Vacuum Hose Snout
3. Control Grips
4. 109 cm (43 in) Vacuum Hose
5. Vacuum Bag Compartment /
Recovery Tank
6. Battery Compartment
7. Compartment Latches
8. Swivel Casters & 300 mm (12 in) Rear Wheels
9. Squeegee Kit (Optional)
3
10
11
12
14
13
10. Machine ON/OFF Switch
11. Drain Hose
12. Squeegee Kit Lift Pedal (Optional)
13. Charger Plug
14. 3 m (10 ft) Vacuum Hose

OPERATION
6Typhoont16B (10–03)
MACHINE INSTALLATION
UNCRATING MACHINE
Carefully check carton for signs of damage. Report
damages at once to carrier.
Check Machine Contents to ensure package is
complete. Contact distributor for missing items.
Machine Contents:
1 –Battery Cable #130364
4 –Battery Post Caps #45962
2 –Red Battery Boots #611222
2 –Black Battery Boots #611221
1 –3m (10 ft) Vacuum Hose #160481
1 –109 cm (43 in) Vacuum Hose #160630
1 –Paper Bag #611785
1 –Cloth Bag #900105
2 –12VDC 105AH Batteries #578426 (included with
machine PAC #607623)
1 –Battery Charger, 24DC/12A 120V #603553
(included with machine PAC #607623)
NOTE: Squeegee and Accessory Tools Kits are
optional, they must be ordered separately (See
OPTIONS section).
INSTALLING BATTERIES
NOTE: If planning to install Optional Squeegee Kit,
wait to install the batteries until kit is installed
(See ATTACHING OPTIONAL SQUEEGEE KIT).
WARNING: Keep Sparks And Open Flame
Away. Keep Battery Hood Open When Charging.
FOR SAFETY: When servicing machine, wear
protective gloves and safety glasses when
handling batteries or battery cables. Avoid contact
with battery acid.
Recommended Battery Specifications:
Two 12 volt 105/130 amp hour deep cycle batteries.
Maximum battery dimensions are 340 mm (13.5 in) L x
180 mm (7 in) W x 250 mm (10 in) H.
1. Turn ON/OFF switch to off.
ATTENTION: Make sure tanks are empty before
opening.
2. Open battery compartment, unlatch lower latches
and carefully tilt upper housing backwards to floor.
Remove loose battery cables at bottom of
compartment (Figure 1).
FIG. 1
3. Carefully install batteries into compartment and
arrange battery posts as shown. Connect the
battery cables to the battery posts as shown, RED
TO POSITIVE & BLACK TO NEGATIVE. Use the
battery post covers and rubber boots supplied
(Figure 2).
(–)
(+)
(–)
(+)
FIG. 2
ATTENTION: Do not drop batteries into
compartment. Battery and machine housing
damage may result.
4. Apply a light coating of non–metallic grease or
protective spray on the cable connections to
prevent battery corrosion.
ATTACHING OPTIONAL SQUEEGEE KIT
NOTE: Kit installation is made easy if batteries are not
installed. However, kit can be installed with batteries in
place.
1. Remove vacuum bags and/or empty recovery
tank.
2. Tip machine on backside –only if batteries are
removed from machine.

OPERATION
Typhoont16B (10–03) 7
3. Remove two unused squeegee mounting screws
from bottom of machine.
4. Install squeegee mounting bracket as shown.
Secure with screw and washers that you removed
(Figure 3).
FIG. 3
5. Fasten squeegee bracket to mounting bracket.
Use two (2) clevis and cotter pins provided
(Figure 4).
FIG. 4
6. Stand machine upright.
7. Insert spacer through hole in pedal then position
pedal between two holes in squeegee bracket.
Secure with hardware provided (Figure 5).
FIG. 5
8. Slide pedal between the two mounting arms on
back of machine. Align and insert clevis pin
through arms and slot in pedal, secure with cotter
pin (Figure 6).
FIG. 6
9. Attach squeegee assembly to bracket as shown
and secure with two thumb screws (Figure 7).
FIG. 7
10. Connect the 1090 mm (43 in) vacuum hose to the
squeegee assembly and to cover snout (Figure 8).
FIG. 8

OPERATION
8Typhoont16B (10–03)
MACHINE SETUP
WET VACUUMING
1. Open machine cover and remove vacuum bag
from recovery tank (Figure 9).
FIG. 9
2. Make sure automatic float shut-off screen is in
place (Figure 10).
FIG. 10
ATTENTION: To prevent vacuum motor damage,
automatic float shut-off screen must be in place.
DRY VACUUMING
1. Open machine cover and install cloth filter bag,
make sure that the bag edge is properly seated on
compartment rim (Figure 11).
For easy debris disposal and to increase the life of
cloth filter bag, use a paper vacuum bag with the
cloth bag. Place the paper bag inside of cloth bag
and tuck the top of paper bag around outside rim
of cloth bag. Never use paper bag without cloth
filter bag in place. Do not reuse paper bags –
always dispose.
FIG. 11
ATTENTION: Always make sure that a bag is in
place before dry vacuuming. Operating machine
without bag in place will damage vacuum motor.
This damage is NOT covered by warranty.
2. Close cover and fasten latches.
3. Leave automatic float shut–off screen in place
when dry vacuuming. It can provide limited
vacuum motor protection for a faulty bag.
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
WARNING: Do Not Operate Machine In Or
Near Flammable Liquids, Vapors Or Combustible
Dusts.
WARNING: Do Not Pick Up Flammable Or
Toxic Materials, Burning Or Smoking Debris.
VACUUM MOTOR THERMAL PROTECTOR
The vacuum motor is thermally protected by a
temperature sensor device. It will trip if motor has an
overload. If motor should quit, wait 20 minutes for
motor to cool and remove obstruction before
continuing.

OPERATION
Typhoont16B (10–03) 9
OPERATING ACCESSORY TOOLS
1. Connect 3m (10 ft) vacuum hose to machine cover
snout.
2. Select desired accessory tool and connect to
vacuum hose (Figure 12).
FIG. 12
3. Activate ON/OFF switch and operate accessory
tool as normal.
4. During DRY vacuuming, check bag periodically for
fullness. For best suction performance, empty bag
at 3/4 full.
During WET vacuuming, the float shut-off screen
will automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If you are vacuuming up liquids that
may cause foaming inside recovery tank, use a
quality defoamer chemical to eliminate the foam.
Foam will NOT shut off automatic float and will
damage vacuum motor. Damage due to foam is
NOT covered by warranty.
OPERATING SQUEEGEE KIT OPTION
1. Lower squeegee to floor, lightly kick the pedal
forward to release from transport position
(Figure13).
FIG. 13
2. Activate the ON/OFF switch.
3. Begin operating by pushing and pulling machine in
either direction.
4. During operation, the float shut-off screen will
automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If you are vacuuming up liquids that
may cause foaming inside recovery tank, use a
quality defoamer chemical to eliminate the foam.
Foam will NOT shut off automatic float and will
damage vacuum motor. Damage due to foam is
NOT covered by warranty.
5. To raise squeegee, step downward on pedal until
pedal engages in the transport position
(Figure 14).
FIG. 14
NOTE: Squeegee Kit can be used to pick up fine
particles (dust, sand, sawdust, etc...). The squeegee
is not recommended for ordinary dry pick up.
DRAINING RECOVERY TANK
1. Push machine to nearest floor drain, if not
available use a bucket to drain machine.
2. Remove drain hose from holder and twist off drain
hose cap and drain. Raise hose to stop flow of
water (Figure15).
FIG. 15

OPERATION
10 Typhoont16B (10–03)
3. After draining recovery tank, open cover and
thoroughly rinse out tank with clean water.
4. Replace drain hose knob securely and return to
holder.
ATTENTION: Be certain drain hose knob is secure
to prevent suction loss.
CHARGING BATTERIES
To prolong battery life, ONLY recharge batteries after
a total of 30 minutes or more of use.
The following charging instructions are intended
for supplied 24V chargers only. Use a charger with
the following specifications to prevent battery
damage.
CHARGER SPECIFICATIONS:
SOUTPUT VOLTAGE - 24 VOLTS
SOUTPUT CURRENT - 15 AMPS
SAUTOMATIC SHUTOFF CIRCUIT
SFOR DEEP CYCLE BATTERY CHARGING
ATTENTION: Do not continue to run machine
when pick–up performance begins to decrease,
battery damage may result.
WARNING: Keep Sparks And Open Flame
Away. Keep Battery Hood Open When Charging.
FOR SAFETY: When servicing machine, wear
protective gloves and safety glasses when
handling batteries or battery cables. Avoid contact
with battery acid.
1. Turn On/Off switch to off.
2. Push the machine to a flat, dry surface in a well–
ventilated area for charging.
3. Open battery compartment. Unlatch lower latches
at front of machine and carefully tilt upper housing
backwards to floor (Figure 16).
NOTE: Make sure to drain the tank prior to accessing
the batteries.
FIG. 16
4. Before charging, check the fluid level (A) in each
battery cell. If the battery plates (B) are exposed,
add just enough distilled water to cover plates. DO
NOT OVERFILL. Overfilled batteries can overflow
during charging due to fluid expansion. Replace
cell caps before charging (Figure 17).
A
B
FIG. 17
5. With the charger’s power supply cord unplugged,
connect the battery charger into the machine’s
charging receptacle as shown (Figure 18).
FIG. 18
6. Plug the charger’s power supply cord into a
grounded wall outlet (Figure 19).
Grounded
3 Hole Outlet
Ground Pin
FIG. 19
FOR SAFETY: Do not operate charger unless cord
is properly grounded.
WARNING: Keep Sparks And Open Flame
Away. Keep Battery Hood Open When Charging.
NOTE: Once the charger is connected, the machine
will become inoperable.