nodon MSP-2-1-11 User manual

The NodOn®Micro Smart Plug + Metering allows to control (Power
ON or Power OFF) an electrical appliance plugged on it: bedside
lamp, electrical heater, coffee machine, etc. Once set up (see the
set up procedures below), the NodOn®Micro Smart Plug can be
controlled by different EnOcean®compliant emitters (wall switch,
remote controller, sensor, window handle, card switch, etc.).
Check the compliant emitters list below.
Thanks to build-in Metering features, the Micro Smart Plug can
meter Instantaneous Power (W) and Accumulated Energy (Wh),
between two buffer's reset.
INSTALLATION
1Plug the NodOn®Micro Smart Plug on your power outlet.
2Plug the electrical appliance, you want to control, on the NodOn®
Micro Smart Plug.
3The Micro Smart Plug allows to switch ON (Power ON) or switch
OFF (Power OFF) the electrical appliance you want to control.
Switching ON or OFF can be done through the Micro Smart Plug
local button, or any kind of emitter paired to the Micro Smart Plug
(check the next steps of the user guide).
If the electrical appliance (ex.: bedside lamp) has an ON/OFF button, make sure it’s positioned
on “ON”, in order that the power ON of the appliance by the Micro Smart Plug will switch ON
the lamp.
MICRO SMART PLUG MODES
LOCAL CONTROL
The Micro Smart Plug can be switched ON or OFF locally, through
a short press on the local button. By default, the Micro Smart Plug
is switched ON when the LED is green, OFF when the LED is OFF.
PAIRING MODE
Press on the Micro Smart Plug button during 2 seconds until the
LED becomes red. Release the button.
The LED will then glow in red. The Micro Smart Plug is in “Pairing
mode”
To pair an emitter, follow the “Pairing procedures”. To conrm that
the pairing is OK, the LED will blink in green.
If the LED blinks orange during “Pairing mode”, it means that the
memory of the Micro Smart Plug is full, or that no emitter has been
paired during the process.
In case of full memory, please unpair an emitter before being able
to pair a new one.
Note: The NodOn®Micro Smart Plug supports the EnOcean®Remote Commissioning features.
It can be put wirelessly into « Pairing mode » through a compatible home automation gateway.
<1s
<1s
ON
OFF
2s {Shining}
FACTORY RESET
To perform a factory reset, press on the Micro Smart Plug button
during 5 seconds until the LED becomes orange. Release the
button, the LED will blink red/green.
The factory reset will remove all the emitters from the Micro Smart
Plug memory, and set all the parameters of the Micro Smart Plug
to default value.
Factory Reset clears Energy (Wh) buffer as well.
PAIRING PROCEDURES
Wall Switch, Remote Controller, etc.
EnOcean®Type “Rocker Switch” (EEP: F6-02-01)
To pair this type of emitter to the Micro Smart Plug:
1Put the Micro Smart Plug in “Pairing mode”.
2Press any button of the emitter. The button pressed during the
pairing process is the button which will switch ON the Micro Smart
Plug. The opposite button will switch OFF the Micro Smart Plug.
The other buttons of the emitter will not be able to control the
Micro Smart Plug.
Pairing Mode Usage
Button paired during
“Pairing mode”
Button pressed on
the emitter
Micro Smart Plug
state
IION
OOFF
OO ON
IOFF
PPON
MOFF
MMON
POFF
To unpair this emitter:
1Put the Micro Smart Plug in “Pairing mode”.
2Press any button of the emitter
The emitter can’t control the Micro Smart Plug anymore.
Key Card Activated Switch
EnOcean®Type “Key Card Activated Switch” (EEP: F6-04-01)
To pair this type of emitter to the Micro Smart Plug:
1Put the Micro Smart Plug in “Pairing mode”.
2Insert or remove the card from the reader. The movement of
the card done during the pairing process is the movement which
will switch ON the Micro Smart Plug. The opposite movement will
switch OFF the Micro Smart Plug
3To initialize the Micro Smart Plug, insert and remove (or remove
and insert) the card.
Pairing Mode Usage
Movement done during
« Pairing mode » Card position Micro Smart Plug state
INSERT INSERTED ON
REMOVED OFF
REMOVE REMOVED ON
INSERTED OFF
To unpair this emitter:
1Put the Micro Smart Plug in “Pairing mode”.
2Insert or remove the card.
The emitter can’t control the Micro Smart Plug anymore.
>5s {Shining}
Window Handle
EnOcean®Type “Window Handle” (EEP: F6-10-00)
To pair this type of emitter to the Micro Smart Plug:
1Put the Micro Smart Plug in “Pairing mode”.
2Make the relevant movement with the handle according to your
need. Check below table.
Note: “Bottom hung” and “Open” position are identically considered
Pairing Mode Usage
Movement done during
« Pairing mode » Handle position Micro Smart Plug state
OPEN or BOTTOM HUNG
OPENED or
BOTTOM HUNG ON
CLOSED OFF
CLOSE
CLOSED ON
OPENED or
BOTTOM HUNG OFF
To unpair this emitter
1Put the Micro Smart Plug in “pairing mode”.
2Make any kind of movement with the handle.
The emitter can’t control the Micro Smart Plug anymore.
Opening sensor
EnOcean®Type “Magnetic Contact” (EEP: D5-00-01)
To pair this type of emitter to the Micro Smart Plug:
1Put the Micro Smart Plug in “Pairing mode”.
2Press on the “learning” button of the opening sensor. The
position (close or far) of the magnet from the sensor when the
“learning” button is pressed is the position which will switch ON
the Micro Smart Plug. The opposite position will switch OFF the
Micro Smart Plug. Check the table below.
Pairing Mode Usage
Magnet position when the
« Learning » button is
pressed
Magnet position Micro Smart Plug
state
CLOSE CLOSE ON
FAR OFF
FAR FAR ON
CLOSE OFF
To unpair this emitter:
1Put the Micro Smart Plug in “pairing mode”.
2Press on the “learning” button
The emitter can’t control the Micro Smart Plug anymore.
Motion sensor
EnOcean®Type “PIR Sensor” (EEP: A5-07-01 / A5-07-02 / A5-
07-03 / A5-08-01 / A5-08-02 / A5-08-03)
To pair this type of emitter to the Micro Smart Plug:
1The status of the Micro Smart Plug (ON or OFF) chose before
put in “pairing mode” will be associate with a presence detection
2Put the Micro Smart Plug in “pairing mode”.
3Press the “learning” button of the presence sensor.
When a presence is detected, the Micro Smart Plug will be in the
state (ON or OFF) dened at step 1.
When no presence is detected, the Micro Smart Plug will be in the
opposite state. Check the table below.
Pairing Mode Usage
Micro Smart Plug state
before “pairing mode” Sensor status Micro Smart Plug state
ON PRESENCE ON
NO PRESENCE OFF
OFF NO PRESENCE ON
PRESENCE OFF
To unpair this emitter:
1Put the Micro Smart Plug in “pairing mode”.
2Press on the “learning” button.
The emitter can’t control the Micro Smart Plug anymore.
Open
Bottom hung
Close
Open
Bottom hung
Open
Bottom hung
learning
close
far
Power supply: 230V AC ~ 50Hz
Self-consumption <1W
Max. power: 1840W continuous (Resistive load)
Metering of Instantaneous Power (W) and accumulated Energy (Wh)
Center radio frequency : 868.3 MHz
Occupied frequency band : 868.0 to 868.6 Mhz
RF power Max : +3dBm
Range up to: 60m outdoor / 30m indoor
Operational temperature: 0°C / 35°C
IP20
Memory capacity : 24 emitters
EEP (Prol EnOcean®): D2-01-0E
Dimensions: 46mm (Diameter) x 74mm (H)
Weight: 67g
Warranty: 2 years
USER GUIDE
Micro Smart Plug
METERING
Micro Smart Plug Type E
Reference: MSP-2-1-01
Micro Smart Plug Schuko
Reference: MSP-2-1-11

Dry contact sensor
EnOcean®Type “Dry Contact” (EEP: A5-10-0A / A5-10-0B / A5-
14-01 / A5-14-02 / A5-14-03 / A5-14-04)
To pair this type of emitter to the Micro Smart Plug:
1The status of the Micro Smart Plug (ON or OFF) chose before
put in “pairing mode” will be associate with a closed circuit.
2Put the Micro Smart Plug in “pairing mode”.
3Press the “learning” button of the dry contact sensor.
When the contact is closed, the Micro Smart Plug will be in the
state (ON or OFF) dened at step 1.
When the contact is open, the Micro Smart Plug will be in the
opposite state. Check the table below.
Pairing Mode Usage
Micro Smart Plug state
before « Pairing mode » Contact status Micro Smart Plug state
ON CLOSE ON
OPEN OFF
OFF OPEN ON
CLOSE OFF
To unpair this emitter:
1Put the Micro Smart Plug in “pairing mode”.
2Press on the “learning” button.
The emitter can’t control the Micro Smart Plug anymore.
HOME AUTOMATION GATEWAY
PAIR THE MICRO SMART PLUG WITH
A HOME AUTOMATION GATEWAY
The NodOn®Micro Smart Plug can be controlled by an EnOcean®
compliant Home Automation gateway.
For the pairing process of the Micro Smart Plug with the gateway,
please refer to the user guide of your Home Automation gateway.
Below, a standard learning process:
1Put your gateway in learning mode
2Put the Micro Smart Plug in “Pairing mode”.
3 The interface of your gateway will conrm the success of the pairing process.
Nota: To unpair the Micro Smart Plug, the procedure is the same
Find the list of the supported Home Automation gateway on
www.nodon.fr – “Support” section.
PARAMETERS OF THE MICRO SMART PLUG
The NodOn®Micro Smart Plug is bi-directional and follows the D2-
01-0E EnOcean® Equipment Prole (EEP):
PARAMETERS D2-01-0E
No. of output channels 1
Switching X
Local Control X
Local control enable/disable X
Taught-in devices enable/disable X
User interface day/night mode X
Default state congurable X
Energy measurement X
Power measurement X
Measurement Roll-over X
Measurement congurable X
Measurement report on query X
Measurement auto-reporting X
SUPPORTED PROFILES (EEP)
F6-02-01 F6-04-01 F6-10-00
D5-00-01 A5-07-01 A5-07-02
A5-07-03 A5-08-01 A5-08-02
A5-08-03 A5-10-19 A5-10-18
A5-10-1A A5-10-1B A5-10-1C
A5-10-1D A5-10-01 A5-10-05
A5-10-08 A5-10-0C A5-10-10
A5-10-13 A5-10-16 A5-10-17
A5-10-0A A5-10-0B A5-14-01
A5-14-02 A5-14-03 A5-14-04
WARNING!
Unplug the product only when it is powered OFF.
Do not plug the products one behind the other.
Do not use the product in a humid area.
The product must be easy to access once plugged.
PICTOGRAM
This product is compliant with all relevant European
standards.
When sorting your waste, please observe the
disposal regulations in force. Please place your
waste in the facilities provided for that purpose and
with all due respect for the environment.
This product must be used indoor only.
This product is compliant with EnOcean®radio
protocol.
CONTACT
Manufacturer & Importer:
ID-RF SAS
121 rue des Hêtres
45590 St CYR EN VAL (FRANCE)
AFTER SALES
www.nodon.fr section “support”
[email protected]
For user guides in other languages, please visit
www.nodon.fr/notices
DEFAULT PARAMETERS
PARAMETERS Default
Local Control enable/disable Enable
Taught-in Devices enable/disable Enable
User interface day/night mode Day
Default state congurable Previous State
Unit Energy Query Wh
Unit Power Query W
Report measurement Query only
Measurement delta to be reported 0
Time between two subsequent
actuator (minimum and maximum)
0
Repeater enable/disable Disable
Repeater Level OFF
PARAMETERS PRESENTATION
Switching:
This option is to switch ON or OFF the Micro Smart Plug. If :
- Output value = (0x00) the Micro Smart Plug is switched OFF
- Output value between (0x01) and (0x64), the Micro Smart Plug is
switched ON.
The Micro Smart Plug doesn’t have any dimming function.
Local control:
This option is to activate or deactivate the local control of the
Micro Smart Plug.
In both case, you can always access to the “Pairing mode” and
“Factory Reset”.
Taught-in devices:
If the parameter is activated, all the emitters paired to the Micro
Smart Plug can control it.
If the parameter is deactivated, only the Home Automation
gateway can control the Micro Smart Plug.
User interface day/night mode:
If the parameter is set to “Day”, the LED will be green when the
Micro Smart Plug is ON, and will be OFF when the Micro Smart
Plug is OFF.
If the parameter is set to “Night”, the LED will be OFF whatever the
Micro Smart Plug state.
Default State:
This parameter allows dening the state of the Micro Smart Plug
after a power failure.
Metering:
For details about all Metering parameters and commands, please
report to the latest version of the "EnOcean® Equipment Proles"
(EEP) or your home automation gateway interface.
For more information about each parameter (function, implementation, etc.) and advanced set-
up, please refer to the user guide of your Home Automation gateway.
If you are a Home Automation gateway manufacturer, please refer to the latest version of the
“EnOcean® Equipment Proles (EEP)”.